2015.5 Peugeot Boxer wheel bolts

11 2
Good practice
If your vehicle is fitted with airbags, observe the safety guidelines below for these to be fully effective.
Wear a correctly adjusted seat belt.
Sit in a normal upright position.
Do not leave anything between the
occupants and the airbags (child, animal,
object...), do not fix or attach anything near
to or in the trajectory of the airbags as this
could cause injuries during deployment.
Never modify the original definition of your
vehicle, particularly in the area directly
around the airbags.
All work on the airbag systems must be
carried out by a P
eugeOt dealer or a
qualified workshop.
After an accident or if the vehicle has been


stolen or broken into, have the airbag
systems checked. Front airbags
Do not drive holding the steering wheel
by its spokes or resting your hands on the
centre part of the wheel.
Passengers must not place their feet on the
dashboard.
Smoke as little as possible; deployment of
the airbags can cause burns or the risk of
injury from a cigarette or pipe.
Never remove or pierce the steering wheel
or hit it violently.
Lateral airbags
Fit only approved covers on the front seats,
compatible with the deployment of lateral
airbags. For information on the range of
covers suitable for your vehicle, contact a
P
eugeOt dealer.
Do not fix or attach anything to the front seat


backs.
this could cause injury to the chest


or arms when the lateral airbag is deployed.
Do not sit with the upper part of the body
any nearer to the door than necessary.
curtain airbags
Do not fix or attach anything to the pillars or


the roof.
this could cause injury to the head


when the curtain airbag is deployed.
Do not remove the bolts from the grab
handles installed on the roof, they play a
part in securing the curtain airbags.
Airbags

158
- extend the jack using the wheelbrace d
and trhe bar B until the wheel is a few

centimetres off the ground.
-


u
nscrew the bolts fully and remove the

wheel to be repaired.
- Position the jack c at one of the four
locations provided on the underbody

near the wheels.
If your vehicle has a folding foot board, the
jack must be positioned at 45°.
removing the wheel to be repaired
- Remove the trim (depending on version)
using the screwdriver E as a lever.
-
Release the bolts using the
wheelbrace
d and the bar B .
Puncture

159
Fitting the spare wheelStowing the wheel
- Put the spare wheel in place on the hub
and fit the bolts by hand.
-
Pre-tighen the bolts using the
wheelbrace
d and the bar B .
-
Lower the vehicle completely by folding
the jack
c, then remove the jack.
-


t
ighten the bolts again using the
wheelbrace
d and the bar B (tighten


them fully without forcing them). You must place the wheel to be repaired or
the spare wheel under the vehicle to secure
the carrier system.
-
Place the wheel at the rear of the vehicle.
●
For eversions with steel wheels

, hook
the carrier H on the outside.
●
Screw in the grip G to secure the carrier


and wheel. ● For versions with alloy wheels
, position
the strap
j on the outside.
●
Fit the three strap fixing screws I to the


alloy wheel.
QuICK HeLP
8
Puncture

160
Refer to the "technical data -
Identification markings" section for the
location of the tyre pressure label.
- Fit the long socket A
, the wheelbrace d
and bar
B to the securing screw.
-


t
urn the assembly clockwise to fully
draw in the cable and raise the wheel


under the vehicle.
-
Check that the wheel is positioned
horizontally flat against the floor of the


vehicle and that the the cut-out for the
carrier system is visible.
-
Stow the tools and the trim (depending
on version).
refitting the repaired wheel
Refitting the repaired wheel is the same as
fitting the spare wheel; don't forget to refit
the wheel trim.
the spare wheel is not designed to be used


over long distances. Have the tightening
of the bolts and pressure of the spare
wheel checked by a P
eugeOt dealer or a
qualified workshop without delay

.
Also, have the original wheel repaired and
refitted by a P
eugeOt dealer or a qualified
workshop as soon as possible.
Puncture