2015.5 Citroen BERLINGO MULTISPACE RHD oil type

47
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
SERVICE INDICATOR
This programmes service intervals according  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few seconds,  the   spanner   flashes   and   the   number   of miles/kilometres

  remaining   is   displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
  recorder   resumes   normal  
operation

  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A
 

few
 
moments
 
after
 
the
 
ignition
 
has been switched on, the spanner
indicating

 
a
 
service
 
operation
 
comes
 
on; the display for the total distance
recorder

 
gives
 
(in
 
round
 
figures)
 
the
 
distance

 
remaining
 
before
 
the
 
next
 
service.
The points at which a service is due
are

 
calculated
 
from
 
the
 
last
 
indicator
 
zero

 
reset.
The point at which a service is due is
determined
 
by
 
two
 
parameters:
-

the distance travelled,
-

 
the

 
time
 
which
 
has
 
elapsed
 
since
 
the

 
last
 
service.
The
 
distance
 
remaining
 
before
 
the
 
next

 
service
 
may
 
be
 
weighted
 
by
 
the

 
time
 
factor,
 
depending
 
on
 
the
 
type

 
of
 
driving. With the engine running the spanner
remains
  on   until   the   service   has   been  
carried

  out.
For BlueH
d i d iesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination   of   the   Service   warning  
lamp,

  on   switching   on   the   ignition.
Each
  time   the   ignition   is  
switched on and for a few
seconds, the spanner
flashes

  and   the   excess  
distance

  is   displayed.
For BlueH
d i d iesel versions, the
spanner
  can   also   come   on   early,  
according the level of deterioration
of

  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
REadY To Go
3

158
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Levels
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

DIESEL
162
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Fuel
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
FUEL CUT- OFF
In a serious collision, a mechanism automatically
  prevents   fuel   from  
reaching

  the   engine.
The
  flashing   of   this   warning  
lamp

  is   accompanied   by   a  
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-

switch of
f the ignition
(ST
o

P

position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
DIESEL PRIMING PUMPFuel used for Diesel engines
The Diesel engines  are  compatible  with  biofuels
  which   conform   to   current   and  
future European standards (

d iesel fuel
which
  complies   with   standard   EN   590  
mixed

  with   a   biofuel   which   complies  
with standard E

n 14214) available at
the
  pumps   (containing   up   to   7   %   Fatty  
Acid

  Methyl   Ester).
B30 biofuel can be used in certain
Diesel
  engines.   However,   this   use,  
even occasional, requires strict
application of the special servicing
conditions.

  Contact   a   CITROËN   dealer  
or

  a   qualified   workshop.
The use of any other type of (bio)fuel
(vegetable  or   animal   oils,   pure   or   diluted, domestic

  fuel...)   is   strictly   prohibited
 (risk

  of   damage   to   the   engine   and   fuel
 system).
If you run out of fuel, it is necessary to
prime  the   fuel   circuit.
Other HDi engines
- Fill  the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-
 
Squeeze
  and   release   the   manual  
priming

  pump,   under   the   bonnet,  
under

  the   protective   cover.
-
o perate the starter until the engine
starts.
BlueHDi engine
- Fill   the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Switch on the ignition (without
starting

  the   engine).
-
 
W
ait   around   6   seconds   and   switch  
of

f   the   ignition.
-
 
Repeat
  the   operation   10   times.
-
o perate the starter to run the
engine.