47
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
SERVICE INDICATOR
This programmes service intervals according to the use of the vehicle.More than 1 000 miles/km before the
next service is due
Example:
4 800 miles/km remain
before
the next service is due. When
the ignition is switched on and for a
few
seconds, the screen shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
recorder resumes normal
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few seconds, the spanner flashes and the number of miles/kilometres
remaining is displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
recorder resumes normal
operation
and the spanner remains on.
This indicates that a service should be
carried
out shortly.
Service overdue
Operation
A
few
moments
after
the
ignition
has been switched on, the spanner
indicating
a
service
operation
comes
on; the display for the total distance
recorder
gives
(in
round
figures)
the
distance
remaining
before
the
next
service.
The points at which a service is due
are
calculated
from
the
last
indicator
zero
reset.
The point at which a service is due is
determined
by
two
parameters:
-
the distance travelled,
-
the
time
which
has
elapsed
since
the
last
service.
The
distance
remaining
before
the
next
service
may
be
weighted
by
the
time
factor,
depending
on
the
type
of
driving. With the engine running the spanner
remains
on until the service has been
carried
out.
For BlueH
d i d iesel versions, this
alert
is also accompanied by the fixed
illu
mination of the Service warning
lamp,
on switching on the ignition.
Each
time the ignition is
switched on and for a few
seconds, the spanner
flashes
and the excess
distance
is displayed.
For BlueH
d i d iesel versions, the
spanner
can also come on early,
according the level of deterioration
of
the engine oil. Deterioration of the
engine oil depends on the conditions of
use
of the vehicle.
REadY To Go
3
48
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Trip recorder zero
reset button
after this operation, if you wish to
disconnect the battery, lock the
vehicle
and wait for at least five
minutes,
otherwise the zero re-set will
not
be registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few
seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
with the
service
warning lamp,
accompanied
by an
audible
signal and a message in the
screen, indicates a low oil level which
could
damage the engine.
If the low oil level is confirmed by a
check
using the dipstick, it is essential
that
the level is topped up.
Oil level gauge fault
Flashing of "OIL--"
indicates a
malfunction of the
engine oil level
indicator
. Contact a CITROËN dealer
or
a qualified workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 30 minutes.Dipstick
A
= maximum, never exceed
this level as a surplus of oil
may
damage the engine.
Contact a CITR o Ë n dealer
or a qualified workshop
without
delay.
B
=
minimum,
top
up
the
level
via
the oil filler cap, using the
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
and controls.
When the lighting
reaches
the minimum (or
maximum)
setting, release the button
then press it again to increase (or
reduce)
the
brightness.
a
s soon as the lighting is of the
required
brightness, release the button.
Zero reset
Your CITROËN dealer or a qualified workshop carries out this operation
after
each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-
switch of
f the ignition,
-
press and hold the trip recorder
reset button,
-
switch
on the ignition.
The
display begins a countdown.
When the display shows "=0", release
the
button; the spanner disappears.
