2015.5 Citroen BERLINGO MULTISPACE RHD fuel

18
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
This locks and unlocks the vehicle's doors,  opens   and   closes   the   fuel   filler  
cap, as well as starting and stopping
the

  engine.
KEYR EMOTE CONTROL
Unlocking
Locking
Press this button to lock all of your
  vehicle's   doors.
The
 
direction   indicators   flash   once.
If one of the doors is open or is not
closed
 
correctly,   the   central   locking   will  
not

 
work.
Deadlocking
A second press on the closed
padlock   on   the   remote   control   within  
five seconds

  after   locking   changes   the  
locking

  to   deadlocking.
This
  is   confirmed   by   fixed   lighting  
of the direction indicators for
approximately

  two   seconds.
Deadlocking
  renders   the   exterior  
and interior door opening handles
inoperative:

  do   not   leave   anyone   inside  
the

  vehicle   when   it   is   deadlocked.
If
  deadlocking   is   activated   from   inside  
the

  vehicle   using   the   remote   control,   it  
will

  change   to   normal   locking   when   the  
vehicle

  is   started.
Press
 
this
 
button
 
to
 
unlock
 
all
 of
 
your
 
vehicle's
 
doors.
The
 
direction
 
indicators
 
flash
 
twice.
access

22
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
SLIDING SIDE DOORS
From the outside
Pull the handle towards you then
towards the rear and open the side
door guiding the rearward sliding to
beyond the point of resistance to hold
it  open.
A
 

mechanical   system   prevents   opening  
of the left-hand side door when the fuel
filler

  flap   is   open.
From the inside
Unlock the side door using this handle and open it, guiding the rearward
sliding  to   the   point   of   resistance.   Pass  
this

  point   to   hold   the   door   open.
Close the side door using the handle
to start the sliding and pass the point
of
  resistance.  
Then,
  use   the   shaped  
recess at the top of the door pilla

r to
guide
  the   door   until   it   locks.
d

o not use the grab handle to slide the
door.
Good practice
Take care not to block the guide space on   the   floor   to   allow   the   door   to   slide  
correctly

.
If
  your   vehicle   is   parked   on   a   slope,  
guide

  the   sliding   of   the   side   door.   In  
fact,

  the   door   could   open   or   close   more  
rapidly due to the slope of the ground
and

  could   cause   injury.
For safety and operation reasons, do
not drive with the sliding side doors
open.
access

28
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Dials
1. Distance  recorder   in   kilometres   /  miles.
2.
 
Display
  screen.
3.
 
Fuel
  gauge,   coolant   temperature.
4.
 
Rev
  counter.
5.
 
T
rip   distance   recorder   /   service  
indicator

  reset.
6.
 
Instrument
  panel   lighting   dimmer.Level 1
INSTRUMENT PANELDisplay screens
Screens
The format of the information presented in the screen depends on
the
  vehicle's   equipment   level.
Level 2
with the touch screen tablet

34
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Warning lamp isindicatesSolution - action
Front /
lateral
airbag flashing
  or  
remaining

  on.a
  failure   of   an   airbag.Have
  the   system   checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop   without   delay.
Chapter
  5,   "Airbags"   section.
Front
passenger's
airbag
deactivated on. the intentional deactivation
of this airbag in the
presence of a rearward
facing
  child   seat.Chapter
  5,   "Airbags"   or   "child   safety"   section.
Low fuel
level on with gauge
needle in the
red
  zone.When
  it   first   comes   on,  
there

  remains   around  
8 litres

  of   fuel   in   the   tank.  
The distance you can drive
on this fuel depends on
your style of driving and the
engine

  type.You
  must   fill   up   with   fuel   to   avoid   running   out.
This
  warning   lamp   comes   on   each   time   you  
switch

  on   the   ignition   until   you   have   filled   up.
Capacity
  of   the   tank:   approximately   60   litres.
Never
  risk   driving   until   the   tank   is   empty,   this  
could

  damage   the   emissions   and   injection  
systems.
flashing. cutting of

f of the fuel supply
following
  a   serious   impact.Restore
  the   supply.
Chapter
  7,   "Fuel"   section.
EOBD
emission
control
system flashing
  or  
remaining

  on.a
  failure   of   the   system.There
  is   a   risk   of   damage   to   the   catalytic  
converter

.   Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Battery
charge on.
a fault in the charging
circuit. Check
  the   battery   terminals,   …
Chapter
  8,   "Battery"   section.
flashing. placing of the active
functions on standby
(economy
  mode).Chapter
  8,   "Battery"   section.
remaining
  on,  
in spite of the
checks.an

  ignition   or   injection  
malfunction.Have

  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.

+
ABS
35
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Warning lamp isindicatesSolution - action
Power
steering on. a fault with the
system.The vehicle retains conventional steering without
assistance.
  Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Door open
detection on
  and   accompanied  
by

  a   message   in   the  
screen.that a door is not
closed

  correctly.Check
  that   all   of   the   doors   are   closed.
ABS remaining
  on.a fault with the anti-
lock
  braking   system.The
  vehicle   retains   conventional   braking.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
ESC flashing.
triggering of the
a

SR
or
  DSC   regulation.The
  system   optimises   traction   and   improves   the  
directional

  stability   of   the   vehicle.
Chapter
  5,   "Driving   safety"   section.
remaining
  on.a fault with the
system.
E.g.:
  under-inflation  
of

  the   tyres.E.g.:
  check   the   pressure   of   the   tyres.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.   (Wheel   speed   sensor,  
hydraulic

  valve   block,   ...).
Under-
inflation on.
The tyre pressure is
too
  low   in   or   more  
wheels.Check

  the   tyre   pressure   as   soon   as   possible.
This
  check   must   be   done   with   the   tyres   cold.
flashing
  then
 remaining

  on,
 accompanied

  by   the
 Service

warning
lamp,
  and   depending
 on

  equipment,   the
 display

  of   a   message.The tyre pressure
monitoring
  system  
has a fault or one of
the wheels does not
have

  a   sensor.Detection
  of   under-inflation   is   no   longer   assured.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Particle filter on. a
  problem   with   the  
particle

  filter   (fuel  
additive

  level,   risk   of  
blockage, ...).Have

  the   filter   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop.
Chapter
  7,   "Levels"   section.
READY TO GO
3

37
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Warning lamp in the
screenis
indicates Solution - action
Cruise
control on.
cruise
  control   selected.Manual
  selection.
Chapter
  4,   "Steering   mounted   controls"   section.
Speed limiter on.speed
  limiter   selected.Manual
  selection.
Chapter
  4,   "Steering   mounted   controls"   section.
Gear shift
indicator on.a
  recommendation  
independent of the type and
density

  of   traffic.To
  reduce   fuel   consumption,   change   to   an  
appropriate

  gear   with   a   manual   gearbox.
The driver retains responsibility to follow this
indication
  or   not.
Diesel pre-
heating on.climatic
  conditions   requiring  
pre-heating.W

ait   until   the   warning   lamp   goes   off   before  
operating

  the   starter.
Presence of
water in the
Diesel filter
on and
accompanied by
  a   message   in
 the

  screen.
water in the Diesel filter. Have   the   filter   bled   by   a   CITROËN   dealer   or   a  qualified
  workshop   without   delay.
Chapter   7,   "Checks"   section.
According
  to   country.
Service
spanner on.that a service will be due
shortly. Refer
  to   the   list   of   checks   in   the   maintenance   and  
warranty

  guide.
Have the service carried out by a CITR
o Ë n
dealer
  or   a   qualified   workshop.
Time flashing. adjustment
  of   the   time.Use
  the   left-hand   button   on   the   instrument   panel.
Chapter
  3,   "Instruments   and   controls"   section.
REadY To Go
3

40
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
FUEL GAUGEC OOLANT TEMPERATURE
The needle is positioned before the
red zone:
  normal   operation.
In arduous conditions of use or hot
climatic
  conditions,   the   needle   may  
move

  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-  
stop
  immediately,   switch   off   the  
ignition.

 
The
  fan   may   continue   to  
operate

  for   a   certain   time,   up   to  
approximately

  10   minutes,
-
wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As   the   cooling   system   is   pressurised,  
follow the procedure below to avoid the
risk

  of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   in   the   header   tank,
-  if   necessary,   remove   the   cap   to  
top up.
If

  the   needle   remains   in   the   red  
zone,

  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The
 
fuel
 
level
 
is
 
tested
 
each
 
time
 
the
 
key

 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the
 
warning
 
lamp
 
comes
 
on
 
continuously

.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.

41
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
EMISSIONS CONTROLS
EoBd (European on Board diagnosis) is a diagnostics
system
  which   complies  
with,

  among   others,   the  
standards on the authorised
emissions of:
-

 
CO

 
(carbon   monoxide),
-

HC (unburnt hydrocarbons),
-

no
x (nitrous oxides) or particles,
detected by oxygen sensors placed
upstream
  and   downstream   of   the  
catalytic

  converters.
The
 
driver
 
is
 
warned
 
of
 
any
 
malfunction
 
of

 
this
 
emission   control   system   by   the  
illu

mination   of   this   specific   warning  
lamp

 
in
 
the   instrument   panel.
There
 
is
 
a   risk   of   damage   to   the  
catalytic

 
converter.   Have   it   checked  
by

 
a
 
CITROËN   dealer   or   a   qualified  
workshop.
UNDER-INFLATION DETECTION
This system continuously  monitors  
the pressures of the four
tyres, as soon as the
vehicle

  is   moving.
a pressure sensor is located in the
valve of each tyre (except the spare
wheel).
The

 
system
 
triggers   an   alert   if   a   drop  
in

 
pressure
 
is
 
detected   in   one   or   more  
tyres.The

 
tyre
 
under-inflation   detection  
system

 
is
 
an   aid   to   driving   which  
does not replace the need for
vigilance

 
on   the   part   of   the   driver.This
  system   does   not   avoid   the  need
  to   check   the   tyre   pressures  
regularly (including the spare
wheel)

  and   before   a   long   journey.
Driving
  with   under-inflated   tyres  
adversely af

fects road holding,
extends
  braking   distances   and   causes  
premature

  tyre   wear,   particularly   under  
arduous conditions (vehicle loaded,
high

  speed,   long   journey).
Driving
  with   under-inflated   tyres  
increases

  fuel   consumption.
The tyre pressures for your vehicle
can be found on the tyre pressure
label.
Refer
  to   chapter   9,   "Identification  
markings"

  section.
The
  tyre   pressures   must   be   checked  
when the tyres cold (vehicle stopped
for 1 hour or after driving for less then
6

  miles   (10   km)   at   moderate   speed).
Otherwise,
  add   0.3   bar   to   the   values  
indicated

  on   the   label.
REadY To Go
3