2015.5 Citroen BERLINGO MULTISPACE RHD change time

72
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Good practice
For maximum cooling or heating of the passenger  compartment,   it   is   possible  
to exceed the value 15 by turning until
LO

  is   displayed   or   the   value   27   by  
turning

  until   HI   is   displayed.
o

n entering the vehicle, the inside
temperature
  may   be   much   colder  
(or
  warmer)   than   is   comfortable.  
There
 
is no advantage in changing the value
displayed

  in   order   to   quickly   reach   the  
level

  of   comfort   required.  
The
  system  
will

  use   its   maximum   performance   to  
reach

  the   comfort   value   set.
DIGITAL AIR CONDITIONING
Automatic operation
AUTO comfort programme
This
  is   the   normal   air   conditioning  
system

  operating   mode. Driver or passenger side comfort
value
The value indicated in the screen
corresponds
  to   a   level   of   comfort   and  
not

  a   temperature   in   degrees   Celsius  
or

  Fahrenheit.
Turn this control to the left
or to the right to decrease or
increase   the   value.  
A 
setting  
around the value 21 provides
optimum

  comfort.   However,  
depending

  on   your   requirements,   a  
setting

  between   18   and   24   is   usual.
d

o not cover the sunshine sensor
located
  on   the   dashboard.
Press this button, the AUTO
symbol
  is   displayed.
The
  system   controls   the  
distribution,

  the   flow   and   the  
intake

  of   air   to   guarantee  
comfort

  and   a   sufficient   circulation  
of

  air   in   the   passenger   compartment  
according

  to   the   comfort   value   set.   No  
further

  action   on   your   part   is   required.Air
  flow   will   increase   gradually   when  
the

engine is cold, to prevent excessive
distribution   of   cold   air.
For   your   comfort,   the   settings   are  
stored when the ignition is switched of

f
and   are   reinstated   the   next   time   the  
vehicle

  is   started.
The   automatic   function   will   no   longer  
be

  maintained   if   you   change   a   setting  
manually

  (AUTO   is   cleared).
SEPARATE SETTINGS FOR DRIVER AND
PASSENGER
Ventilation

101
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Replacing a cartridge
The scented air freshener refill consists of a cartridge B and its sealing case C.
-
 
Remove
  the   protective   film   D.
-

Place the head of the cartridge
B
on the button A of the scented air
freshener.
-
 
T
urn   it   a   quarter   of   a   turn   to   lock   it  
on

  the   button   and   remove   the   case.
-

Insert the scented air freshener in
its

  location.
You can change the cartridges at any
time
  and   store   cartridges   which   have  
already been started in their original
case.
The scented air freshener button

A is
independent
  of   the   cartridge.
The cartridges are supplied without the
button A.
Inserting the scented air
freshener
After fitting or changing the cartridge:
-  
Put
  the   scented   air   freshener   back  
in

  place   in   its   location.
-

T
urn it a quarter of a turn to the
right.
Good practice
as a safety precaution, only use the
cartridges   provided   for   this   purpose.  
Do

  not   dismantle   the   cartridges.
k

eep the cartridge sealing cases
which
  are   used   as   packaging   when   the  
cartridges

  are   not   in   use.
Never
  try   to   refill   the   cartridges   with  
fragrances other than those available
from

  CITROËN   dealers.
k

eep out of reach of children and
animals.
 
A
void   contact   with   the   skin  
and

  eyes.   If   swallowed,   consult   a  
doctor

  and   show   him   the   packaging   or  
product

  label.
The scented air freshener button A can
only
 
be
 
fixed
 
on
 
the
 
multifunction
 
roof
 
console

 
with
 
a
 
cartridge.
Therefore, always retain button A and
a
 
cartridge.
The
 
cartridges
 
are
 
available
 
from
 
CITROËN

 
dealers.
EaSE oF USE and CoMFoRT
4
Practical information

160
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Checks
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Good practice
Only use products recommended by CITRo Ë n or products of equivalent
quality
  and   specification.
In
  order   to   optimise   the   operation  
of

  units   as   important   as   the   braking  
system,

  CITROËN   selects   and   offers  
specific

  products.
Bleeding water from the Diesel
filter Manual gearbox
Have the level checked in accordance with the
  manufacturer's   servicing   schedule.
In order to avoid damaging the electrical units, high pressure
washing to clean the engine
compartment
  is   strictly   prohibited.
After
  washing   the   vehicle   dampness,  
or

 
in
  winter,   ice   may   form   on   the   brake  
discs

  and   pads:   braking   efficiency   may  
be

 
reduced.   Make   some   light   brake  
applications to dry and de-ice the
brakes.
If

 
this
 
warning
 
lamp
 
comes
 
on,

 
bleed
 
the
 
filter.
 
Otherwise
 
bleed

 
regularly
 
each
 
time
 
the
 
engine

 
oil
 
is
 
changed.
H

d
i engines use advanced
technology.
 
All

 
work
 
requires
 
special training, so should be
entrusted

 
to
 
a
 
CITROËN
 
dealer.
Depending
 
on
 
country
 
of
 
sale.
To drain the water, unscrew the bleed
screw
 
located
 
on
 
the
 
filter.
o

perate until all of the water no longer
flows
 
in
 
the
 
transparent
 
pipe,
 
then
 
tighten

 
the
 
bleed
 
screw.

 165
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
AdBlue® additive
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Range indicators
Rules on the display of alertsFor   more   information   on   the  
displays

  and   warning   lamps,   refer  
to

  chapter   3,   "Instruments   and  
controls"

  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the URE

a

warning

  lamp   comes   on   temporarily  
and

  the   remaining   range   message   is  
displayed.
The

  alert   is   repeated   every   150   miles  
(300

  km)   until   the   next   threshold   is  
reached.
Every

  time   the   ignition   is   switched  
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1 500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If
  the   range   is   greater   than   3   000   miles  
(5

  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "
d riving
assistance"
  menu,
-

select "
d iagnostic",
-
 
select
  CHECK.
d
ifferent levels of alert are triggered
according
  to   the   remaining   driving  
range

  threshold.
You
  will   be   informed   as   each   mileage  
threshold is reached and the alerts will
change

  from   temporary   to   permanent.
-

The 1st is triggered at a remaining driving
  range   of   1   500   miles  
(2
 
400
  km).
-
The 2nd is triggered at a remaining driving
  range   of   350   miles   (600 km).
-
 
Up

 
to
 
0   miles,   at   which   point   it   will  
be

 
impossible   to   restart   the   engine  
after

 
a
 
stop.
CHECKS
7

172
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. T

ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel

184
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb

Audio and Telematics
 229
Berlingo-2-VP_en_Chap10a_SMEGplus_ed02-2015
Select change of source.
P ress on Radio Media
to display the
primary
 pag
e.
Select " DAB Radio ".
Select " List"
  in   the   primary   page.
Select
 
the   radio   station   from   the   list   offered.Press on Radio Media
to display the
primary
 pag
e.
Press   on   the   secondary   page.
Select " Settings ".
Select " RADIO".
Select " Digital/FM auto
tracking " then "Confirm ".
DAB / FM auto tracking
D
igital radio
"daB" does not cover 100% of the
te r r i to r y.
When the digital radio signal is poor,
"DAB / FM
  auto   tracking"   allows   you   to  
c

ontinue   listening   to   the   same   station,  
b

y   automatically   switching   to   the  
c

orresponding "FM" analogue station
(if
  there   is   one). If
  "DAB / FM   auto   tracking"   is   activated,  t
here is a difference of a few seconds
when
  the   system   switches   to   "FM"  
a

nalogue   radio   with   sometimes   a  
v

ariation   in   volume.
When the digital signal is restored, the
system
  automatically   changes   back  
t

o "DAB".di
gital radio provides higher quality
reception and also the graphical display
of
 
current
 
information
 
on
 
the
 
radio
 
s

tation
 
being
 
listened
 
to.
 
Select
 
"List"
 
in
 
t

he
 
primary
 
page.
The
 
range
 
of
 
multiplexes
 
available
 
is
 
d

isplayed
 
in
 
alphabetical
 
order. If the "
d

a
B
" station being listened to
is not available on "FM" (" DAB/FM"
option
  greyed   out),   or   "DAB   /   FM   auto  
t

racking"   is   not   activated,   the   sound  
w

ill cut out while the digital signal is too
weak.
or
Select " Radio list " in the secondary
page.
TECHNOLOGY on BOARD
10

Audio and Telematics
230
Berlingo-2-VP_en_Chap10a_SMEGplus_ed02-2015
Media
USB playerSelection of source
The steering mounted SRC ( s o u r c e)
button can be used to go to the next
media
  source,   available   if   the   source  
i

s   active.
Select
  change   of   source.
Press on Radio Media
to display the
primary
 pag
e.
The
 
system
 
builds
 
playlists
 
(in
 
temporary
 
m

emory),
 
an
 
operation
 
which
 
can
 
take
 
from
 
a

 
few
 
seconds
 
to
 
several
 
minutes
 
at
 
the
 
first
 
c

onnection.
Reduce
 
the
 
number
 
of
 
non-music
 
files
 
and
 
the
 n
umber
 
of
 
folders
 
to
 
reduce
 
the
 
waiting
 
time.
The
 
playlists
 
are
 
updated
 
every
 
time
 
the
 
i

gnition is switched off or connection of a USB
memory
 
stick.
 
The
 
lists
 
are
 
memorised:
 
if
 
they
 
a

re
 
not
 
modified,
 
the
 
subsequent
 
loading
 
time
 
w

ill
 
be
 
shorter.
Insert
 
the
 
USB
 
memory
 
stick
 
into
 
the
 
USB
 
port
 
o

r connect the USB device to the USB port
using
 
a
 
suitable
 
cable
 
(not
 
supplied).
Auxiliary socket (AUx)
Connect the portable device (MP3 player…) to t
he   auxiliary   Jack   socket   using   an   audio   cable  
(

not
 sup
plied).
First
  adjust   the   volume   of   your   portable   device  
(

to   a   high   level).   Then   adjust   the   volume   of   your  
a

udio   system.
Display
  and   management   of   the   controls   are  
v

ia   the   portable   device. Choose
  the   source.