2014 YAMAHA SR400 warning

PERIODIC MAINTENANCE AND ADJUSTMENT
6-38
1
2
3
4
567
8
9
10
11
12
9. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
TIPThe drive chain does not need to be
disassembled in order to remove andinstall the wheel.
To install the rear wheel1. Install the spacer into left side of the wheel hub.
2. Install the chain pullers and the wheel by inserting the wheel axle
from the left-hand side.
3. Install the drive chain onto the rear sprocket. 4. Install the washer and axle nut.
5. Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting nut
onto the brake rod.
6. Connect the brake torque rod to the brake shoe plate by installing
the bolt, washer and nut.
7. Adjust the drive chain slack. (See page 6-22.)
8. Take the motorcycle off the center- stand so that the rear wheel is on
the ground, and then put the side-
stand down.
9. Tighten the brake torque rod nut and axle nut to the specified
torques.
10. Adjust the brake pedal free play. (See page 6-18.)
WARNING
EWA10661
After adjusting the brake pedal free
play, check the operation of the
brake light.
1. Drive chain
1
Tightening torques:Brake torque rod nut:19 Nm (1.9 m·kgf, 14 ft·lbf)
Axle nut: 129 Nm (12.9 m·kgf, 92 ft·lbf)
2RD-9-E0.book 38 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-39
1
2
3
4
56
7
8
9
10
11
12
EAU25852
TroubleshootingAlthough Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
WARNING
EWA15142
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or
property damage.
2RD-9-E0.book 39 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

MOTORCYCLE CARE AND STORAGE
7-3
1
2
3
4
5
67
8
9
10
11
12 including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11132
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.

If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10801

Apply spray oil and wax spar-
ingly and make sure to wipe off any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from thelens.
EAU43203
StorageShort-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the motor-
cycle.NOTICE
ECA10811

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter.
2RD-9-E0.book 3 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

MOTORCYCLE CARE AND STORAGE
7-4
1
2
3
4
5
678
9
10
11
12
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10952]
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 C (30 F) or more than 30
 C (90 F)]. For more information
on storing the battery, see page
6-28.TIPMake any necessary repairs beforestoring the motorcycle.
2RD-9-E0.book 4 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

SPECIFICATIONS
8-3
1
2
3
4
5
6
78
9
10
11
12
Rear turn signal light: 12 V, 21.0 W  2
Auxiliary light:
12 V, 4.0 W  1
Meter lighting: 12 V, 1.7 W  4
Neutral indicator light: 12 V, 1.7 W  1
High beam indicator light:
12 V, 1.7 W  1
Turn signal indicator light: 12 V, 1.7 W  1
Fuel level warning light: 12 V, 3.0 W  1
Engine trouble warning light:
12 V, 1.7 W  1Fuses:Main fuse:
30.0 A
Headlight fuse:
15.0 A
Signaling system fuse: 15.0 A
Ignition fuse: 10.0 A
Parking lighting fuse:
7.5 A
Fuel injection system fuse: 7.5 A
Backup fuse: 7.5 A
2RD-9-E0.book 3 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

10-1
1
2
3
4
5
6
7
8
91011
12
INDEX
AAir filter element, replacing ...................... 6-12
Auxiliary light bulb, replacing ................... 6-34BBattery ..................................................... 6-28
Brake and clutch levers, checking and lubricating .............................................. 6-25
Brake fluid, changing ............................... 6-21
Brake fluid level, checking ....................... 6-20
Brake lever ................................................ 3-6
Brake lever free play, adjusting ............... 6-17
Brake light switches ................................. 6-19
Brake pads and shoes, checking............. 6-20
Brake pedal ............................................... 3-6
Brake pedal, checking and lubricating ..... 6-25
Brake pedal height and free play, adjusting ................................................ 6-18CCables, checking and lubricating ............. 6-24
Care ........................................................... 7-1
Catalytic converter ..................................... 3-9
Centerstand and sidestand, checking and lubricating ....................................... 6-26
Clutch lever................................................ 3-5
Clutch lever free play, adjusting .............. 6-16DDecompression lever ............................... 3-11
Dimmer switch ........................................... 3-4
Drive chain, cleaning and lubricating ....... 6-23
Drive chain slack ..................................... 6-22EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-13
Engine oil and oil filter element.................. 6-9 Engine serial number ................................ 9-1
Engine stop switch .................................... 3-5
Engine trouble warning light ...................... 3-3
FFront fork, checking................................. 6-27
Fuel ........................................................... 3-7
Fuel cock ................................................. 3-10
Fuel consumption, tips for reducing .......... 5-3
Fuel level warning light .............................. 3-3
Fuel tank breather/overflow hose .............. 3-9
Fuel tank cap............................................. 3-7
Fuses, replacing ...................................... 6-29HHandlebar switches ................................... 3-4
Hazard switch............................................ 3-5
Headlight bulb, replacing......................... 6-31
High beam indicator light ........................... 3-3
Horn switch ............................................... 3-5IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-13
Indicator lights and warning lights ............. 3-2KKickstarter ............................................... 3-10MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-4
Maintenance, emission control system ..... 6-3
Matte color, caution ................................... 7-1
Model label ................................................ 9-2NNeutral indicator light ................................ 3-2PPanel, removing and installing .................. 6-7 Parking.......................................................5-4
Part locations .............................................2-1
Pass switch ................................................3-4
SSafety information ......................................1-1
Seat ......................................................... 3-11
Shifting .......................................................5-2
Shift pedal ..................................................3-6
Shift pedal, checking................................ 6-19
Shock absorber assemblies, adjusting ....3-12
Sidestand .................................................3-12
Spark plug, checking .................................6-8
Specifications.............................................8-1
Speedometer unit ......................................3-3
Starting the engine.....................................5-1
Starting the engine, trouble........................5-2
Steering, checking ................................... 6-27
Storage ......................................................7-3
Swingarm pivots, lubricating .................... 6-26TTachometer................................................3-4
Tail/brake light bulb, replacing ................. 6-32
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking............... 6-13
Tires ......................................................... 6-14
Tool kit .......................................................6-2
Troubleshooting ....................................... 6-39
Troubleshooting chart ..............................6-40
Turn signal indicator light ...........................3-2
Turn signal light bul b, replacing ............... 6-33
Turn signal switch ......................................3-4VValve clearance ....................................... 6-13
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分