2014 TOYOTA VERSO S light

205
2-1. Driving procedures
2
When driving
VERSO-S_EE
Parking brake
Usage in winter time
See “Winter driving tips” for parking brake usage in winter time. (P. 259)
NOTICE
Before driving
Fully release the parking brake.
Driving the vehicle with the parking brake set will lead to brake components
overheating, which may affect braking performance and increase brake
wear.
To set the parking brake, fully pull the parking brake lever while
depressing the brake pedal.
To release the parking brake, slightly raise the lever and lower it
completely while pressing the button.

207
2
When driving
VERSO-S_EE
2-2. Instrument cluster
Gauges and meters
Tachometer
Displays the engine speed in revolutions per minute.
Speedometer
Displays the vehicle speed.
Outside temperature display
P. 342
Fuel gauge
Displays the quantity of fuel remaining in the tank.
Display change button
P. 208
Odometer, trip meter, Stop & Start system operation time, Stop &
Start system total operation time, meter light control and multi-
information display
P. 208, 219
Clock
P. 341
Clock adjusting buttons
P. 341

209 2-2. Instrument cluster
2
When driving
VERSO-S_EEStop & Start system total operation time (if equipped)
Instantaneous fuel consumption
P. 220
Average fuel consumption
P. 221
Driving range
P. 221
Meter light controlDisplays the total amount of time that the engine
has been stopped due to operation of the Stop &
Start system since the system was last reset.
Press and hold the button to reset.
Displays the brightness of the meter light when
the headlight switch is on.
Pressing and holding the button will adjust bright-
ness of the meter light.

210 2-2. Instrument cluster
VERSO-S_EE
Customization display
Changing the Eco Driving Indicator Light status (vehicles with
a Multidrive)
Eco Driving Indicator Light can
be activated or deactivated by
pressing the button when the
Eco Driving Indicator Light cus-
tomization display is displayed.
To display the Eco Driving Indica-
tor Light customization display,
display the odometer and press
and hold the display change but-
ton for 5 seconds or more.
When customization is complete,
press and hold the button for 2
seconds or more to return to the
odometer display.

212 2-2. Instrument cluster
VERSO-S_EE
NOTICE
To prevent damage to the engine and its components
Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
The engine may be overheating if the high engine coolant temperature
warning light flashes or turns on. In this case, immediately stop the vehicle
in a safe place, and check the engine after it has cooled completely.
(
P. 505)

213
2-2. Instrument cluster
2
When driving
VERSO-S_EE
Indicators and warning lights
The indicators and warning lights on the instrument cluster, center
panel and dashboard inform the driver of the status of the vehicle’s
various systems.
Instrument cluster
Center panel

215 2-2. Instrument cluster
2
When driving
VERSO-S_EE
Indicators
The indicators inform the driver of the operating state of the
vehicle’s various systems.
Turn signal indicator
(P. 204)
(Vehicles with
a manual
transmission)
Gear Shift Indicator
(P. 202)
Headlight high beam
indicator (P. 223)
(Diesel engine)
Engine preheating
indicator (P. 176, 186)
(If equipped)
Tail light indicator
(P. 222)
(If equipped)
Cruise control indicator
(P. 245)
(If equipped)
Front fog light indicator
(P. 228)
(If equipped)
Cruise control set indi-
cator (P. 245)
Rear fog light indicator
(P. 228)VSC OFF indicator
(P. 250)
(If equipped)
Smart entry & start sys-
tem indicator (P. 176)“TRC OFF” indicator
(P. 250)
(If equipped)
Stop & Start indicator
(P. 238)
(Vehicles with
a Multidrive)
“SPORT” indicator
(P. 191)
Engine immobilizer/
alarm system indicator
(P. 107)Slip indicator
(P. 250)
Low engine coolant
temperature indicator
*1
*1
*1
*1
*1, 2
*3

216 2-2. Instrument cluster
VERSO-S_EE
*1: These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode (vehicles with a smart entry & start
system) or the engine switch is turned to the “ON” position (vehicles
without a smart entry & start system) to indicate that a system check
is being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the vehi-
cle inspected by any authorized Toyota dealer or repairer, or
another duly qualified and equipped professional.
*2: The light flashes to indicate that the system is operating.
*3: This indicator turns on when the engine coolant temperature is low.
(Vehicles with
a Multidrive)
Eco Driving Indicator
Light (P. 166)
(If equipped)
Stop & Start cancel indi-
cator (P. 238)
(Vehicles with a multi-mode manual transmis-
sion)
Shift position and gear position indi-
cators (P. 196)
(Vehicles with a Multidrive)Shift position and gear step position
indicators (P. 190)
Airbag manual on-off indicator
(P. 135)
*1*1