2014 TOYOTA PRIUS V reset

14
PRIUS v_OM_OM47840U_(U)
Pictorial indexInstrument panel
Headlight switch
Turn signal lever Fog light switch P. 213
P. 194
P. 219
Pre-collision braking off switch P. 257
Parking brake pedal P. 195
Fuel filler door opener P. 115
Tire pressure warning reset switch P. 391
Windshield wipers and washer switch
Rear window wiper and washer switch P. 221
P. 226
Gauges and meters
Trip-information display P. 197
P. 201
Audio system*2 P. 294
Navigation system*1
SRS driver airbag
Horn P. 124
P. 196
Card holder P. 311
Tilt and telescopic steering control lever P. 107
SRS knee airbag P. 124

51
1-1. Hybrid system
1
Before driving
PRIUS v_OM_OM47840U_(U)
■
Resetting the consumption data
Display Audio system
Selecting “Clear” on the “Trip Information” screen will reset the fuel con-
sumption and the regenerated energy for the past 15 minutes.
Selecting “Clear” on the “History” screen will reset the past records and best
past fuel consumption.
Selecting “Yes” on the following screen will confirm resetting of all the data.
Navigation system
Selecting “Clear” on the “Trip Information” screen will reset the fuel con-
sumption and the regenerated energy for the past 15 minutes.
Selecting “Clear” on the “Past Record” screen will reset the past records and
best past fuel consumption.
Selecting “Yes” on the following screen will confirm resetting of all the data.
■ Cruising range
Displays the estimated maximum distance that can be driven with the quan-
tity of fuel remaining.
This distance is computed based on your average fuel consumption.
As a result, the actual distance that can be driven may differ from that dis-
played.

198 2-2. Instrument cluster
PRIUS v_OM_OM47840U_(U)
Trip information display
Displays fuel consumption, driving range, etc.
Odometer and trip meter display
Odometer: Displays the total distance that the vehicle has been
driven.
Trip meter: Displays the distan ce the vehicle has been driven
since the meter was last reset. Trip meters “A” and
“B” can be used to record and display different dis-
tances independently.
Clock
P. 314

200 2-2. Instrument cluster
PRIUS v_OM_OM47840U_(U)
Changing the displaySwitches between odometer and
trip meter displays. When the trip
meter is displayed, pressing and
holding the “TRIP” button will
reset the trip meter.
When you reset the trip meter, the
average fuel consumption will be
reset as well. (P. 201)
Switching the trip information display
Items displayed can be switched
by pressing the “DISP” button.

201
2-2. Instrument cluster
PRIUS v_OM_OM47840U_(U)
2
When driving
Trip information display
■ Current fuel consumption
■ Average fuel consumption Displays the instant fuel consumption.
The average fuel consumption is displayed on
both the odometer and the trip meter.
• While the odometer is being displayed, or
when the odometer/trip meter are not being
displayed, the average fuel consumption
from the last rese t will be displayed.
• While the trip meter is being displayed, the average fuel consumpt ion will be displayed
in accordance with the trip meter distance
from the last reset.
• The function can be reset by pressing the
“DISP” button for longer than 1 second when
the average fuel consumption is displayed
on the odometer.
• The function can be reset by pressing the “TRIP” button for longer than 1 second when
the average fuel consumption is displayed
on the trip meter.
• Use the displayed average fuel consumption as a reference.

207
2-2. Instrument cluster
PRIUS v_OM_OM47840U_(U)
2
When driving
■
Engine speed
On hybrid vehicles, engine speed is precisely controlled in order to help
improve fuel efficiency and reduce exhaust emissions etc.
There are times when the engine speed that is displayed may differ even
when vehicle operation and driving conditions are the same.
■ Brightness of the in strument panel light
If the headlight switch is turned to ON while the surrounding area is dark, the
instrument panel lights will dim.
■ When disconnecting and reconnect ing 12-volt battery terminals
The average fuel consumption and cruising range will be reset.
NOTICE
■ To prevent damage to the engine and its components
The engine may be overheating if the high coolant temperature warning light
comes on or flashes. In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. ( P. 487)
■ The trip information disp lay at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.

231
2-4. Using other
driving systems
PRIUS v_OM_OM47840U_(U)
2
When driving
■Cruise control can be set when
●The shift position is in D.
● Vehicle speed is above approximately 25 mph (40 km/h).
■ Accelerating after setting the vehicle speed
●The vehicle can be accelerated normally. After acceleration, the set
speed resumes.
● Even without canceling the cruise control, the set speed can be
increased by first accelerating the vehicle to the desired speed and then
pushing the lever down to set the new speed.
■ Automatic cruise control cancelation
Cruise control will stop maintaining the vehicle speed in any of the following
situations.
●Actual vehicle speed falls more than approximately 10 mph (16 km/h)
below the preset vehicle speed.
At this time, the memorized set speed is not retained.
● Actual vehicle speed is below approximately 25 mph (40km/h).
● Enhanced VSC is activated.
■ If the cruise control indicator light comes on in yellow
Press the “ON-OFF” button once to deactivate the system, and then press
the button again to reactivate the system.
If the cruise control speed cannot be set or if the cruise control cancels
immediately after being activated, there may be a malfunction in the cruise
control system. Have the vehicle inspected by your Toyota dealer.

356 4-2. Maintenance
PRIUS v_OM_OM47840U_(U)
■Repair and replacement
It is recommended that genuine Toyota parts be used for repairs to ensure
performance of each system. If non-Toyota parts are used in replacement or
if a repair shop other than a Toyota dealer performs repairs, confirm the war-
ranty coverage.
■ Reset the maintenance data (U.S.A. only)
After the required maintenance is performed according to the maintenance
schedule, please reset the maintenance data.
To reset the data, follow the procedures described below:
Switch the display to the trip meter “A” ( P. 198) when the hybrid
system is operating.
Turn the “POWER” switch off.
While pressing the MPH or km/h button ( P. 199), turn the
“POWER” switch to ON mode (do not start the hybrid system
because otherwise the reset mode will be canceled). Continue to
press and hold the button until the trip meter displays “000000” and
the indicator stops flashing to indicate that the reset is complete.
■ Allow inspection and repairs to be performed by a Toyota dealer
●Toyota technicians are well-trained specialists and are kept up to date
with the latest service information. They are well informed about the
operation of all systems on your vehicle.
● Keep a copy of the repair order. It proves that the maintenance that has
been performed is under warranty coverage. If any problem should arise
while your vehicle is under warranty, your Toyota dealer will promptly
take care of it.
STEP 1
STEP 2
STEP 3