2014 SMART FORTWO COUPE warning

Identification labels
Signs and labels
0043
Air bag information signs
(sun visor)
0044 VIN (engine compartment)
0087 Emission control information label,
includes both federal and California
certification exhaust emission stand-
ards (engine compartment)
0085 Heat warning label (engine compart-
ment)
0083 Certification label (driver’s door
B‑pillar)
0084 Tire and loading information placard
(driver’s door B‑pillar)
006B VIN (lower edge of windshield) Certification label
X Open the driver’s door. 0043
Certification label (on driver’s door
B‑pillar)
i Data shown on the example certifica-
tion label are for illustration purpose
only. These data are specific to each
vehicle and may vary from data shown in
the illustration. Refer to certification
label on vehicle for actual data specific
to your vehicle. Example certification label (U.S. vehicles)
0044 Vehicle Identification Number (VIN)
0087 Paintwork code 214
Identification labels>> Technical data.

Example certification label (Canada vehicles)
0044 Vehicle Identification Number (VIN)
0087 Paintwork code Vehicle Identification Number (VIN)
The Vehicle Identification Number (VIN)
can be found in the following locations:
R on the certification label on the driver’s
door B‑pillar (Y page 214)
R on the rear right on the cargo compart-
ment floor (Y page 215)
R in the lower edge of the windshield
(Y page 214)
X Open the cargo compartment.
X Fold back the carpet. 0043
VIN (on the cargo compartment floor) Vehicle specification
The quoted data apply only to the standard
vehicle. Contact an authorized electric
drive smart center for the corresponding
data of all special bodies and special
equipment. Main dimensions
Overall vehicle
length
107.4 in (2 727 mm)
Overall vehicle
width
11 69.0 in (1 752 mm)
Overall vehicle
height
62.1 in (1 555 mm)
Wheelbase
73.5 in (1 867 mm)
Turning circle
28.7 ft (8.75 m)
Weights
Cargo compart-
ment load
max. 110 lb (50 kg)
Roof load
None
This vehicle is not intended to carry items
on its roof. Thus roof rails and any roof-
mounted devices must not be used.
G
WARNING
No racks or loads may be secured to the roof
of the vehicle, as
R the panorama roof* may be damaged, thus
injuring persons
R this can have a substantial adverse
effect on the driving dynamics of the
vehicle, thus causing accidents
R the rack and/or the load could detach and
through this cause an accident or other
people could be injured by the load and/
or rack that has fallen off
11 Exterior rear view mirrors folded out. Vehicle specification
215>> Technical data.
* optional Z

Mixed size tires
i Abbreviations used in the following tables:
R FA: Front Axle
R RA: Rear Axle All-season tires Light alloy rims
FA
RA 155/60 R 15 74T M+S
175/55 R 15 77T M+S 4.5 J x 15 H2
Wheel offset: 0.93 in (23.5 mm)
5.5 J x 15 H2
Wheel offset: 0.87 in (22 mm)
Winter tires
12 Light alloy rims
FA
RA 155/60 R 15 74T M+S004D
175/55 R 15 77T M+S004D 4.5 J x 15 H2
Wheel offset: 0.93 in (23.5 mm)
5.5 J x 15 H2
Wheel offset: 0.87 in (22 mm)
Service fluids and capacities
Notes
Vehicle components and their respective
lubricants must match. Therefore only use
products tested and approved by smart.
Please contact an authorized electric
drive smart center for products tested and
approved by smart. G
WARNING
Comply with all valid regulations with
respect to handling, storing and disposing
of service fluids. Otherwise you could
endanger persons or the environment.
Keep service fluids out of the reach of chil-
dren.
For health reasons, you should prevent
service fluids from coming into direct
contact with your skin or clothing.
If a service fluid is swallowed, contact a
physician immediately.
12 Not available as factory equipment. Service fluids and capacities
217>> Technical data. Z

Capacities
Components Capacity Coolants, lubricants, etc.
Coolant system approx. 6.9 US qt (6.5 l) Anticorrosion/Antifreeze meet-
ing specification MB 325.0
Air conditioning system 500 g
(17.6 oz) R134a refrigerant (never R 12)
120 g
(4.2 oz) PAG lubricant oil Daphne 1234
Windshield washer sys-
tem 4.0 US qt (3.8 l)
Windshield washer concentrate
13
(Y page 218)
Washer fluid mixing ratio
(Y page 218) Brake fluid
G
WARNING
During vehicle operation, the boiling
point of the brake fluid is continuously
reduced through the absorption of moisture
from the atmosphere. Under extremely
strenuous operating conditions, this mois-
ture content can lead to the formation of
bubbles in the system, thus reducing the
system’s efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s Mainte-
nance Booklet for replacement interval.
Only brake fluid approved by smart is rec-
ommended. Any authorized electric drive
smart center will provide you with addi-
tional information. Windshield/rear window washer system
During all seasons:
X Use a windshield washer concentrate
labeled for summer and water for tem-
peratures above freezing point.
X Use a windshield washer concentrate
labeled for winter and water for temper-
atures below freezing point.
X Premix the windshield washer fluid in a
suitable container depending on the out-
side temperature and in accordance with
the manufacturer’s instructions 14
.
Washer fluid mixing ratio R
Temperature above 32¦ (0¥):
1 part windshield washer concentrate
labeled for summer to 100 parts water
R Temperature of 14¦ (-10¥):
1 part windshield washer concentrate
labeled for winter to 2 parts water
R Temperature of -4¦ (-20¥):
1 part windshield washer concentrate
labeled for winter to 1 part water
13 Use a windshield washer concentrate labeled for summer and water for temperatures above freezing
point or a windshield washer concentrate labeled for winter and water for temperatures below freezing
point.
14 Refer to the notes for use on the container. 218
Service fluids and capacities>> Technical data.

G
WARNING
Windshield washer concentrate is highly
flammable. Fire, naked flames and smoking
are prohibited when windshield washer
concentrate is being handled. Coolants
The battery and drive system coolant is a
mixture of water and anticorrosion/anti-
freeze, which provides:
R Corrosion protection
R Freeze protection
R Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35¦ (-37¥) and cor-
rosion protection.
! Add premixed coolant solution only.
Adding water and MB 325.0 Anticorro-
sion/Antifreeze separately from each
other, could cause drive system damage
not covered by the smart Limited War-
ranty.
If the antifreeze mixture is effective to
-35¦ (-37¥), the boiling point of the
coolant in the pressurized cooling system
is reached at approximately 266¦
(130¥ ).
The coolant solution must be used year
round, even in countries which have high
temperatures to provide the necessary cor-
rosion protection and increase boil‑over
protection. Refer to Maintenance/ Service
Booklet for replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other smart approved products of
equal specification are used to renew the coolant concentration or bring it back up
to the proper level.
For information on other smart approved
products of equal specification, contact an
authorized electric drive smart center.
To provide important corrosion protec-
tion, the solution must be at least 50% anti-
corrosion/antifreeze (equivalent to freeze
protection to approximately -35¦
[-37¥]).
If you use a solution that is more than 55%
anticorrosion/antifreeze (freeze protec-
tion to approximately -49
¦[(-45 ¥]), the
drive system and battery temperature will
increase due to the lower heat transfer
capability of the solution. Therefore, do
not use more than this amount of anticor-
rosion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze should
be used to bring it up to the proper level
(have cooling system checked for signs of
leakage). Please make sure the mixture is
in accordance with label instructions.
Always use anticorrosion/antifreeze that
has been approved by smart. For informa-
tion contact an authorized electric drive
smart center.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water.
If you are not sure about the water quality,
consult an authorized electric drive smart
center.
Capacities Cooling-system
capacity
All models approx. 6.9 US qt
(6.5 l)Service fluids and capacities
219>> Technical data. Z