2014 SKODA YETI transmission

Diesel fuel additives
The diesel fuel in accordance with the prescribed standards meets all the con-
ditions for a smooth running engine. We therefore recommend that no fuel ad-
ditives are used. This can result in considerable damage to parts of the engine
or the exhaust system.
CAUTION
■ Just filling the tank once with diesel fuel that does not comply with the
standard, can cause severe damage to parts of the engine, the fuel and ex-
haust system!■
If a different fuel other than diesel fuel, which complies to the above men-
tioned standards (e.g. petrol) is put into the tank, do not start the engine or
switch on the ignition! Extensive damage to engine parts can occur!
■
Water which has collected in the fuel filter can cause engine faults.
CAUTION
■ The vehicle cannot be operated with biofuel RME, therefore this fuel must
not be refuelled and driven. The use of biofuel RME can cause considerable
damage to parts of the engine or fuel system.■
Do not mix any fuel additives, so-called “flow improvers” (petrol and similar
agents) into the diesel. This can result in considerable damage to parts of the
engine or the exhaust system!
Engine compartment
 Introduction
This chapter contains information on the following subjects:
Opening and closing the bonnet
181
Engine compartment overview
182
Radiator fan
182
Windscreen washer system
182WARNINGInjuries or scolding or risks of accident or fire may occur when working in
the engine compartment. For this reason, it is essential to comply with the
warning instructions outlined below and with the general applicable safety
rules. The engine compartment of your car is a hazardous area!WARNINGInstructions before beginning work in the engine compartment■Turn off the engine and withdraw the ignition key.■
Firmly apply the handbrake.
■
For vehicles with manual transmission the lever into the neutral position.
■
On vehicles with automatic transmission, shift the selector lever into the
P position.
■
Allow the engine to cool.
■
Never open the bonnet if you can see steam or coolant escaping from the
engine compartment – risk of scalding! Wait until no more steam or coolant
is escaping.
WARNINGInformation for working in the engine room■Keep all people, especially children, away from the engine compartment.■
Never touch the radiator fan while the engine is still warm. The fan might
suddenly start running!
■
Do not touch any hot engine parts – risk of burns!
WARNINGInformation for working in the engine compartment with the engine run-
ning■
Pay particular attention to moving engine parts, e.g. V-ribbed belt, gener-
ator, radiator fan - danger to life!
■
Never touch the electric wiring on the ignition system.
■
Avoid short circuits in the electrical system - particularly on the vehicle's
battery.
■
Always make sure that no jewellery, loose clothing or long hair can get
caught in rotating engine parts – risk to life! Always remove any jewellery,
tie back long hair and wear tight fitting clothing before completing any
work.
WARNINGInformation for working on the fuel system or the electrical system■Always disconnect the vehicle battery from the electrical system.■
Do not smoke.
■
Never work near open flames.
■
Always have a functioning fire extinguisher nearby. 
180General Maintenance

›The temporary spare wheel is inflated to the maximum inflation pressure for
the vehicle » page 191.
› Only use this temporary spare wheel to reach the nearest specialist garage,
since it is not intended for permanent use.WARNING■ Never drive with more than one spare wheel mounted!■Only use the spare wheel while absolutely necessary.■
Avoid accelerating at full throttle, sharp braking and fast cornering.
■
The snow chains cannot be used on the spare wheel.
■
Observe instructions on the warning sign of the emergency wheel.
Changing a wheel
 Introduction
This chapter contains information on the following subjects:
Preparation
200
Full wheel trim
200
Wheel bolts
201
Changing a wheel
201
Follow-up tasks
201
Loosening/tightening wheel bolts
202
Raising the vehicle
202
Anti-theft wheel bolts
203
For your own safety and the safety of the passengers, the following instruc-
tions must be observed before changing a wheel on the road.
Switch on the hazard warning lights system.
The warning triangle must be set up at the prescribed distance - observe
the national legal provisions when doing so.
Park the vehicle as far away as possible from the flow of traffic.
Choose a location with a flat, solid surface.
Have all the occupants get out. The passengers should not stand on the
road (instead they should remain behind a crash barrier, for instance) while
the wheel is being changed.
If the vehicle is subsequently fitted with tyres which are different from those it
was fitted with at the works, follow these guidelines » page 193, Explanation
of the tyre labelling .
The national legal requirements must be observed when changing a wheel.
Preparation
Before changing the wheel, the following work must be carried out.
›
Switch off the engine.
›
Engage 1st gear or place the selector lever of the automatic transmission in
the P-position .
›
Firmly apply the handbrake.
›
Uncouple any trailers.
›
Remove the vehicle tool kit » page 198 and the spare wheel » page 199 from
the boot.
Full wheel trim
Before removing the wheel bolts, remove the wheel cover.
Extracting
›
Hook the clamp found in the vehicle tool kit » page 198 into the reinforced
edge of the wheel trim.
›
Push the wheel wrench through the clamp, support on the tyre and pull off
the wheel trim.
Fitting
›
Press the wheel trim onto the wheel rim at the designated valve open-
ing » .
›
Then press the trim into the wheel rim until its entire circumference locks
correctly in place.
CAUTION
■ Use the pressure of your hand only, do not strike the full wheel trim. The
cover could be damaged.■
When using the anti-theft wheel bolt, ensure that it is in the hole in the
valve area.
■
If wheel trims are fitted, an adequate flow of air must be assured in order to
cool the brake system.
Note
We recommend that you use child seats from ŠKODA Original Accessories.200Do-it-yourself

Preparations for using the breakdown kitRead and observe
on page 204 first.
The following preparatory work must be carried out before using the puncture
repair kit.
›
Switch off the engine.
›
Engage 1st gear or place the selector lever of the automatic transmission in
the P-position .
›
Firmly apply the handbrake.
›
Check that you can carry out the repairs with the breakdown kit » page 203.
›
Uncouple any trailers.
›
Remove the breakdown kit from the boot.
›
Stick the sticker
1
» Fig. 178 on page 204 on the dashboard in the driver's
field of view.
›
Unscrew the valve cap.
›
Use the valve remover
2
to unscrew the valve core and place it on a clean
surface (rag, paper, etc.).
Sealing and inflating the tyre
Read and observe
on page 204 first.
Sealing
›
Forcefully shake the tyre inflater bottle
10
» Fig. 178 on page 204 back and
forth several times.
›
Firmly screw the inflation hose
3
onto the tyre inflator bottle
10
in a clock-
wise direction. The film on the cap is pierced automatically.
›
Remove the plug from the inflation hose
3
and plug the open end fully onto
the tyre valve.
›
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
›
Remove the empty tyre inflator bottle from the valve.
›
Screw the valve core back into the tyre valve using the valve remover
2
.
Inflating
›
Screw the air compressor tyre inflation hose
8
» Fig. 178 on page 204 firmly
onto the tyre valve.
›
Check that the air release valve
6
is closed.
›
Start the engine and run it in idle.
›
Plug the connector
4
into 12 Volt socket » page 90.
›
Switch on the air compressor with the ON and OFF switch
9
.
›Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved.
Maximum run time of 8 minutes » .›
Switch off the air compressor.
›
If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation
hose
8
from the tyre valve.
›
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent
to “distribute” in the tyre.
›
Firmly screw the tyre inflation hose
8
back onto the tyre valve and repeat
the inflation process.
›
If you cannot reach the required tyre inflation pressure here either, this
means the tyre has sustained too much damage. You cannot seal with tyre with the breakdown kit »
.
›
Switch off the air compressor.
›
Remove the tyre inflation hose
8
from the tyre valve.
Once a tyre inflation pressure of 2.0 – 2.5 bar is achieved, continue the journey
at a maximum speed of 80 km/h (50 mph).
WARNING■ If you cannot inflate the tyre to at least 2.0 bar, this means the damage
sustained was too serious. The sealing agent cannot be used to seal the
tyre. 
Do not drive the vehicle. Seek help from a specialist garage.■
The tyre inflation hose and air compressor may get hot as the tyre is be-
ing inflated – risk of burning.
CAUTION
Switch off the air compressor after running 8 minutes at the latest – risk of
overheating! Allow the air compressor to cool a few minutes before switching
it on again.
Notes for driving with repaired tyres
Read and observe
on page 204 first.
The inflation pressure of the repaired tyre must be checked after driving for 10
minutes.
If the tyre inflation pressure is 1.3 bar or less
›
 Do not drive the vehicle! You cannot properly seal with tyre with the
breakdown kit.
If the tyre inflation pressure is 1.3 bar or more
›
Set the tyre pressure to the correct value. 
205Emergency equipment and self-help

›If the engine does not start, terminate the attempt to start the engine after
10 seconds and wait for 30 seconds before repeating the process.›
Remove the jump start cables in the reverse order as attachment.
Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the bat-
tery supplying the power must not be significantly less than the capacity of
the discharged battery in your vehicle.
Jump-start cables
Only use jump-start cables which have an adequately large cross-section and
insulated terminal clamps. Observe the instructions of the jumper lead manu-
facturer.
Positive cable - colour coding in the majority of cases is red.
Negative cable - colour coding in the majority of cases is black.
WARNING■
Do not clamp the jump-start cable to the negative terminal of the dis-
charged battery. There is the risk of detonating gas seeping out the battery
being ignited by the strong spark which results from the engine being star-
ted.■
The non-insulated parts of the terminal clamps must never touch each
other – risk of short circuit!
■
The jump-start cable connected to the positive terminal of the battery
must not come into contact with electrically conducting parts of the vehicle
– risk of short circuit!
■
Route the jump-start cables so that they cannot be caught by any rotat-
ing parts in the engine compartment.
■
There must not be any contact between the two vehicles otherwise cur-
rent may flow as soon as the negative terminals are connected.
Towing the vehicle
 Introduction
Fig. 181
Braided tow rope / Spiral tow rope
This chapter contains information on the following subjects:
Front towing eye
208
Rear towing eye
209
Vehicles with a tow hitch
209
For towing, a braided tow rope is to be used » Fig. 181 -
 .
When towing, the following guidelines must be observed.
Vehicles with manual transmission may be towed in with a tow bar or a tow
rope or with the front or rear wheels raised.
Vehicles with automatic transmission may be towed in with a tow bar or a tow
rope or with the front wheels raised. If the vehicle is raised at rear, the auto-
matic gearbox is damaged!
Driver of the tow vehicle
›
Engage the clutch gently when starting off or depress the accelerator partic-
ularly gently if the vehicle is fitted with an automatic gearbox.
›
Only then approach correctly when the rope is taut.
The maximum towing speed is 50 km/h.
Driver of the towed vehicle
›
Switch on the ignition so that the steering wheel is not locked and so that
the turn-signal lights, windscreen wipers and windscreen washer system can
be used. 
207Emergency equipment and self-help

Index
A
abroad lead-free petrol
178
Abroad Headlights
69
ABS Function
143
Warning light38
Acceptance and recycling of used vehicles169
Accessories166
Adaptive headlights (AFS)66
adjusting auxiliary heating and ventilation
111
Adjusting Belt height
15
Exterior mirrors76
Head restraints82
Interior mirror75
seats78
Steering wheel10
the seats electronically78
Adjusting the seats9
Adjusting the seats electronically78
adjustment Front seat
77
Adjustment Headlight beam
64
AFS66
Display messages39
Warning light39
Air-conditioning system Air outlet vents
105
Airbag16
Deactivating21
Deactivating the front passenger airbag22
Deployment17
Front airbag18
Head airbag20
Knee airbag19
Modifications and damage to the airbag system 168
Side airbag
19
Warning light40
Airbag system16
Air conditioning104
Air distribution control106
Climatronic108
manual air conditioning107
Air distribution control106
Air outlet vents105
Alarm Switching off
56
Triggering56
Alcantara cleaning
175
Alternator Warning light
36
Anti-theft alarm system Activating/deactivating
56
Trailer165
Anti-theft wheel bolts203
Antilock Braking System143
Armrest Front
81
artificial leather175
Ashtray89
ASR warning light
37
Assistance systems TSA
144
Assistence systems OFF ROAD-mode
144
Assist system ABS
143
Assist systems142
ABS38
ASR37
Cruise Control System154
DSR144
EDL143
ESC38, 143
HBA144
HHC144
Park assist150
Parking aid146
START-STOP155
TCS143
Audio See Infotainment / radio
4
Auto Check Control33
Automatic driving lamp control66
Automatic gearbox Manual shifting of gears
139
Selector lever-emergency unlocking212
Selector lever lock139
Starting-off and driving140
Tiptronic139
Using the selector lever138
Automatic gearbox modes138
Automatic load deactivation190
automatic transmission selector lever lock defect
139
Automatic transmission138
Kickdown140
Selector lever lock139
Auxiliary heating and ventilation Switching on and off directly
111
System settings111
Auxiliary heating (auxiliary heating and ventila- tion)
110
Radio remote control111
B
Ball head Check fitting
161
Ready position160
231Index

Trailer operation159
Trailer stabilisation (TSA)144
Transmission Warning messages
33
Transport Luggage compartment
96
Roof rack103
Transporting86
Transporting children safely23
Triangle197
TSA144
Turn-signal system Warning light
41
Turn signal65
Two-way radio systems113
Tyre Damage
193
Explanation of the labelling193
see wheels193
Tyre load-bearing capacity see Wheels
194
Tyre pressure191
Warning light40
Tyre pressure monitoring158
Display40
Save tyre pressure values158
Tyre repair General notes
204
Preparations205
Pressure test205
Sealing and inflating the tyre205
Tyres191
new140
Tyre pressure191
Wear and tear192
Wear indicator192
tyre size193
see wheels193
U
Under-body Vehicle care
174
Under-body protection174
Unlock Key
52
Unlocking Individual settings
54
KESSY53
Remote control52
Unlocking and locking51
Used vehicles Acceptance and recycling
169
Useful equipment Ashtray
89
Car park ticket holder86
Cigarette lighter89
Clothes hook94
Cup holders88
Glasses compartment92
Removable through-loading bag95
Storage compartment86
Using the information system42
Using the selector lever138
Using the variable loading floor with a spare wheel
103
V
Variable loading floor
102
Removing and fitting carrier rails103
Variable loading floor with spare wheel Removable storage box
101
Vehicle battery Automatic load deactivation
190
charging189
Checking the battery electrolyte level188
Cover188
Operation in winter188
Replacing190
Safety instructions187
vehicle care chrome parts
172
Vehicle care Alcantara
175
Artificial leather175
Cavity protection173
Cleaning vehicle exterior170
Cleaning wheels173
Decorative films172
Door locking cylinder173
Headlight glasses172
Interior care174
Maintenance171
Materials175
Natural leather175
Plastic parts171
Polishing vehicle paint work171
Rubber seals171
Safety belt176
Seat covers176
Under-body protections174
washing169
Vehicle data sticker222
Vehicle data sticker and nameplate Vehicle data sticker and nameplate
222
Vehicle dimensions224
Vehicle height224
Vehicle Identification Number (VIN)222
Vehicle length224
Vehicle state see Auto Check Control
33
Vehicle tool kit198
Vehicle width224
Vest Placement of the reflective vest
197
VIN Vehicle Identification Number
222
Visibility71
240Index