2014 SKODA CITIGO warning

CAUTIONIf in addition to the symbol  the symbol  » page 35 illuminates while driv-
ing,  stop driving - risk of engine damage! Switch off the engine and seek as-
sistance from a specialist garage.
 Engine oil
Read and observe
on page 34 first.
When the warning light  is
illuminated or is flashing , the engine oil pressure
is too low.
An audible signal sounds as a warning.
›
Stop the vehicle and switch the engine off if the warning light does not ex-
tinguish or if it begins to flash while you are driving.
›
Check the oil level and top up with engine oil if necessary
» page 110, Check-
ing the oil level .
If the oil level is within the specified range and the warning light illuminates
or blinks again after the engine is started,  do not continue driving! Switch
off the engine and seek assistance from a specialist garage.
CAUTION
■ The red oil pressure light  is not an oil level indicator! One should there-
fore check the oil level at regular intervals, preferably after every refuelling
stop.■
 Stop driving if for some reason it is not possible to top up the engine oil
under the current conditions. Switch off the engine and seek assistance from a
specialist garage.
 Coolant
Read and observe
on page 34 first.
If the warning light 
illuminates or flashes , either the coolant temperature is
too high or the coolant level is too low.
An audible signal sounds as a warning tone.
›
Stop the vehicle, switch off the engine, and check the coolant lev-
el » page 112 , Checking the coolant level .
›
If the coolant level is too low, add coolant to the reservoir » page 112.
Do not continue if for some reason it is not possible to fill with coolant under
the current circumstances! This can cause serious engine damage. Therefore,
switch the engine off and seek help from a specialist garage.
If the coolant is within the specified range, the increased temperature may be
caused by an operating problem at the radiator fan.›
Switch off the ignition.
›
Check the fuse for the radiator fan, replace if necessary » page 137, Fuses in
the engine compartment .
If the coolant level and fan fuse are OK and the warning light 
illuminates
again after switching on the ignition, 
stop driving!
Seek help from a specialist garage.
WARNING■ Carefully open the coolant expansion bottle. If the engine is hot, the cool-
ing system is pressurized – risk of scalding! It is therefore best to allow the
engine to cool down before removing the cap.■
Do not touch the radiator fan. The radiator fan may switch itself on auto-
matically even if the ignition is off - a danger of injury is present!
CAUTION
■ Additional headlights and other attached components in front of the air inlet
impair the cooling efficiency of the coolant.■
Never cover the radiator - there is a risk of the engine overheating.
  Automated transmission
Read and observe
on page 34 first.
Warning light 
If the warning light 
illuminates and a beep sounds, then there is a fault to
the automated transmission. 
Do not drive the vehicle! Switch off the engine
and seek assistance from a specialist garage.
Warning light 
If the warning light 
illuminates and no gear change is possible, there may
be technical reasons for why the functionality of the automatic transmission is
limited.
›
Stop the car, turn the ignition off and on again. 
35Instruments and control lights

If the warning light  illuminates after you switch on the ignition, seek assis-
tance from a specialist garage.
If the warning light 
or also the warning light 
illuminates and an acoustic
signal sounds, this means that the automatic gearbox has overheated.›
Stop and allow the transmission to cool down or drive more quickly than
20 km/h (12 mph).
If the warning light 
illuminates repeatedly , park the vehicle, shut off the en-
gine and allow the gearbox to cool down.
Further information » page 80, Automated transmission .

  Power steering
Read and observe
on page 34 first.
If the warning light 
or


illuminates while driving or after switching on the
ignition does not extinguish, there is an error in the electromechanical power
steering.
If the indicator light 
illuminates, this indicates a
complete failure of the
power steering and the steering assist has failed (significantly higher steering
forces).
If the indicator light 
illuminates, this indicates a
partial failure of the power
steering and the steering forces can be greater.
›
Stop the car, turn the ignition off and on again.
If the indicator light does not illuminate after the engine has been turned on
again, the power steering is fully operational again.
If the warning light illuminates again, then immediately obtain assistance from
an authorised dealer.
Note
If the vehicle's battery has been disconnected and reconnected, the warning
light  illuminates after switching on the ignition. If the warning light  does
not extinguish after moving a short distance, this means there is an error in
the system. Seek assistance from a specialist garage immediately. Electronic Stability Control (ESC)
Read and observe
on page 34 first.
The warning light 
flashes to show that the ESC is currently operating.
If the warning light 
illuminates , there is a fault in the ESC. Seek assistance
from a specialist garage immediately.
As the ESC operates in conjunction with the ABS, the ESC warning light will al-
so come on if the ABS system fails.
If the warning light 
illuminates immediately after you start the engine, the
ESC might be switched off due to technical reasons.
›
Switch the ignition off and on again.
If the indicator light 
does not illuminate after you switch the engine back
on, the ESC is fully functional again.
Further information » page 84, Electronic Stability Control (ESC) .
Note
If the vehicle's battery has been disconnected and reconnected, the warning
light  illuminates after switching on the ignition. If the warning light  does
not extinguish after moving a short distance, this means there is an error in
the system. Seek assistance from a specialist garage immediately.
 Traction Control System (TCS)
Read and observe
on page 34 first.
The warning light 
flashes it shows that the TCS currently operating.
If the warning light 
illuminates permanently, there is a fault in the TCS.
Seek assistance from a specialist garage immediately.
The fact that the TCS operates together with the ABS means that the TCS
warning light will also come on if the ABS system is not operating properly.
If the warning light 
illuminates immediately after you start the engine, the
TCS might be switched off due to technical reasons.
›
Switch the ignition off and on again.
If the warning light 
does not illuminate after you switch the engine back
on, the TCS is fully functional again.
Further information » page 85, Traction Control System (TC) .
36Using the system

NoteIf the vehicle's battery has been disconnected and reconnected, the warning
light  illuminates after switching on the ignition. If the warning light  does
not extinguish after moving a short distance, this means there is an error in
the system. Seek assistance from a specialist garage immediately.
Antilock brake system (ABS)
Read and observe
on page 34 first.
If the warning light 
is illuminated , there is a fault in the ABS.
The vehicle will only be braked by the normal brake system without the ABS.
Seek assistance from a specialist garage immediately.
In the event of an ABS fault, the other braking and stabilization systems are
turned off » page 84, Braking and stabilisation systems .
WARNING■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!■
If the ABS warning light 
together with the indicator light 
» page 34
lights, 
do not continue to drive! Seek help from a specialist garage.
 Tyre pressure
Read and observe
on page 34 first.
The warning light 
is illuminated
If the warning light 
illuminates while driving, it means one of the tyres has
undergone a pressure change.
An audible signal sounds as a warning.
›
Immediately reduce speed and avoid sudden steering and braking manoeu-
vres.
›
Stop the vehicle, turn the ignition off and check the tyres and their inflation
pressures » page 118 .
›
Correct the tyre pressure if necessary or replace the affected
wheel » page 124 or use the repair kit » page 127.
›
Save the tyre pressure values in the system » page 92.
The indicator light  flashes for about 1 min. and remains illuminated
If the warning light  flashes for approximately 1 minute and stays illumina-
ted, there may be a fault in the tyre pressure monitoring system.›
Stop the vehicle, turn the ignition off and start the engine again.
If the warning light 
flashes again after the engine has started, there is a
system error.
Seek help from a specialist garage.
The following reasons can explain the warning light 
being illuminated.
› The vehicle is loaded on one side. Distribute loads as evenly as possible.
› The wheels of one axle are loaded more heavily (e.g. when towing a trailer or
when driving uphill or downhill).
› Snow chains are mounted.
› A wheel has been changed.
Save the tyre pressure values in the system » page 92.
CAUTION
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light  in the instrument cluster can be delayed or does
not light up at all.
Note
If the vehicle's battery has been disconnected and reconnected, the warning
light  illuminates after switching on the ignition. If the indicator light does
not extinguish after moving a short distance, this means that there is an error
in the system. Seek help from a specialist garage.
 Rear fog light
Read and observe
on page 34 first.
The warning light 
illuminates when the rear fog light is switched on.
 Exhaust inspection system
Read and observe
on page 34 first.
If the warning light 
illuminates , there is a fault in the exhaust inspection
system. The system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
37Instruments and control lights

 Engine performance checkRead and observe
on page 34 first.
If the indicator light 
illuminates , there is a fault in the engine control. The
system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Airbag system
Read and observe
on page 34 first.
Monitoring the airbag system
If the warning light does not go out for some seconds after the ignition has
been switched on or illuminates while you are driving, there is a fault in the
system »
. This also applies if the warning light does not come on when the
ignition is switched on.
The operational capability of the airbag system is monitored electronically, in-
cluding when one of the airbags is switched off.
One of the airbags or a belt tensioner has been disabled by the diagnostic
tool
› The warning light

illuminates for approx. 4 seconds after switching on the
ignition and then flashes again for approx. 12 seconds afterwards.
The front passenger airbag has been disabled with the key switch
› The warning light

illuminates for a few seconds when the ignition is
switched on;
› The deactivated airbag is indicated by the illumination of the warning light




 in the middle of the dash panel
» page 18, Deactivating
the front passenger airbag .
WARNINGWhen a fault in the airbag system occurs, there is a risk of the system not
being triggered in the event of an accident. Therefore, this must be
checked immediately by a specialized garage.
 Handbrake - automatic transmission
Read and observe
on page 34 first.
If the warning light 
illuminates or blinks, engage the handbrake.
Further information » page 80, Automated transmission .
 Brake pedal (automatic transmission)
Read and observe
on page 34 first.
If the warning light 
illuminates , operate the brake pedal.
Further information » page 80, Automated transmission .
  Turn signal system
Read and observe
on page 34 first.
Either the left  or right
 indicator light
flashes depending on the position of
the control lever.
If there is a fault in the turn signal system, the warning light flashes at twice
its normal rate.
Switching off the hazard warning light system is switched on will cause all of
the turn signal lights as well as both warning lights to flash.
 Cruise control system
Read and observe
on page 34 first.
The warning light 
illuminates when the cruise control is active.
 Main beam
Read and observe
on page 34 first.
The warning light 
illuminates when the main beam or the headlight flasher
is operated.
/ Safety belt (belt status display) - rear seat
Read and observe
on page 34 first.
After switching on the ignition, illumination takes place in the display of the
instrument cluster for 30 s of the symbols  or
 . 
38Using the system

The control symbols  or  indicate whether any passengers have put on their
seat belts in the rear seats.
The passenger on the associated rear seat is belted.
The passenger on the associated back seat is not wearing a seat belt.
If a seat belt is unfastened on the rear seat during the journey at a speed of
more than 25 km/h, an acoustic signal will sound, and the belt status indicator
 for the rear seats
flashes for around 30 seconds.
Further information » page 11, Seat belts .
 City Safe Drive
Read and observe
on page 34 first.
If the indicator symbol 
flashes rapidly, the City Safe Drive system brakes the
car brakes automatically straight away.
If the indicator symbol 
flashes slowly , the system is not available or there is
a system malfunction.
If the system is turned off and the vehicle is moving at a speed of about 5-30
km/h, illumination occurs on the display of the instrument cluster of he warn-
ing symbol  .
If the system is activated again, the warning light

 
in the instrument clus-
ter display illuminates for about 5 s .
Further information » page 90, City Safe Drive .
 /  START-STOP
Read and observe
on page 34 first.
A glowing indicator symbol
 shows the START-STOP system is active.
A glowing indicator symbol
 shows the START-STOP system is active, but no
automatic engine cut-off is possible.
A flashing indicator symbol
 shows the START-STOP system is not available.
Further information » page 88, START-STOP .
Unlocking and opening
Unlocking and locking
Introduction
This chapter contains information on the following subjects:
Unlock / lock using key and lock
40
Unlocking / locking with the remote control key
41
Opening/closing a door
41
Door opening lever
42
Safe securing system
42
Locking / unlocking the vehicle with the central locking button
43
Child safety lock
43
The central locking system allows you to lock and unlock all doors and the lug-
gage compartment lid at the same time » page 44.
The safe securing system » page 42 is integrated in the central locking sys-
tem. Once the car is locked from the outside, the door locks 1)
are automatically
blocked by the safe securing system »
.
The following is true after unlocking
› All the doors and the boot lid are unlocked.
› The interior light operated via the door contact illuminates.
› The safe securing system is switched off 1)
.
› The indicator light in the driver door stops flashing.
The following is true after locking
› All the doors and the luggage compartment lid are locked.
› The interior light operated via the door contact goes out.
› The safe securing system is switched on 1)
.
› The warning light in the driver door begins flashing.
Fault display
If the warning light in the driver's door initially flashes quickly for around 2 sec-
onds, and then illuminates for 30 seconds without interruption before flashing
again slowly, you will need to seek the assistance of a specialist garage. 
1)
This function only applies to certain countries.
39Unlocking and opening

Automatic locking and unlocking
All the doors and the luggage compartment lid are locked automatically once
the car reaches a speed of about 15 km/h.
If the ignition key is withdrawn, the car is then automatically unlocked again. It
is also possible for the driver to unlock the car by pressing the central locking
button.
The vehicle doors can be unlocked and opened at any time by pulling once on
the door opening lever.
Failure of the central locking
If the central locking system fails only the driver's door can be unlocked or
locked with the key. The other doors and the boot lid can be emergency locked
or unlocked.
› Emergency locking of the door
» page 133.
› Emergency unlocking of the luggage compartment lid
» page 134.WARNING■
Never leave the key in the vehicle when you exit the vehicle. Unauthor-
ized persons, such as children, for example, could lock the car, turn on the
ignition or start the engine - there is a danger of injury and accidents!■
When leaving the vehicle, never leave persons who are not completely in-
dependent, such as children, unattended in the vehicle. The children might,
for example, release the handbrake or take the vehicle out of gear. The ve-
hicle could then start to move – risk of injury and accidents! These individu-
als might also not be able to leave the vehicle on their own or to help
themselves. Can be fatal at very high or very low temperatures!
■
If the car is locked from the outside and the safelock system is switched
on, there must not be any person in the car as it is then not possible to
open either a door or a window from the inside. The locked doors make it
more difficult for rescuers to get into the vehicle in an emergency – risk to
life.
CAUTION
■ Each key contains electronic components; therefore it must be protected
against moisture and severe shocks.■
Keep the groove of the keys absolutely clean. Impurities (textile fibres, dust,
etc.) have a negative effect on the functionality of the locking cylinder and ig-
nition lock.
■
The battery must be replaced if the central locking does react to the remote
control at less than around 3 metres away » page 133.
■
When leaving the vehicle, always check if it is locked.■If the driver's door has been opened, the vehicle cannot be locked.
Note
In the event of an accident in which the airbags are deployed, the locked doors
are automatically unlocked in order to enable rescuers to gain access to the
vehicle.
Unlock / lock using key and lock
Fig. 24
Left side of the vehicle: Turning
the key for unlocking and locking
the vehicle
Read and observe and on page 40 first.
The key allows you to unlock and lock the vehicle via the lock cylinder in the driver's door.
Unlocking / locking the vehicle with the key » Fig. 24
Unlocking the vehicle
Locking the vehicle
40Using the system

Unlocking / locking with the remote control keyFig. 25
Remote control key
Read and observe and on page 40 first.
Function and description of the remote control key » Fig. 25
Unlocking the vehicle
Locking the vehicle
Unlocking the boot lid
Button for the extension / retraction of the key
Warning light
Unlocking the vehicle
The turn signal lights flash twice as confirmation that the vehicle has been un-
locked.
If you unlock the vehicle and do not open a door or the boot lid within the next
30 seconds, the vehicle will lock again automatically and the safelock system
will be switched on 1)
. This function is intended to prevent the car being un-
locked unintentionally.
Locking the vehicle
The turn signal lights flash once as confirmation that the vehicle has been
locked.
If the doors or the luggage compartment lid remain open after the vehicle has
been locked, the turn signal lights do not flash until they have been closed.
Unlocking / locking the tailgate
By pressing the symbol key  for about 1 s, only the boot lid is unlocked.
The lid is locked » page 44 by closing.
ABChecking the battery condition
If the red indicator light B » Fig. 25 does not flash when you press a button on
the remote control key, the battery is empty. Replace the battery » page 133.
CAUTION
■
The operation of the remote control may temporarily be affected by signal in-
terference from transmitters close to the car and which operate in the same
frequency range.■
Only operate the remote control when the doors and luggage compartment
lid are closed and the vehicle is in your line of sight.
■
The operating range of the remote control key is approx. 30 m. But this range
of the remote control can be reduced if the batteries are weak.
Opening/closing a door
Fig. 26
Door handle/door opening lever:
Read and observe
and on page 40 first.
Opening from the outside
›
Unlock the vehicle.
›
Pull on door handle
A
» Fig. 26 on the door you wish to open.
Opening from the inside
›
Pull on door opening lever
B
of the respective door and push the door away
from you.
Closing from the inside
›
Grasp pull handle
C
and close the door. 
1)
This function only applies to certain countries.
41Unlocking and opening

WARNING■Make sure that the door has closed correctly as it can open suddenly
while driving – risk of death!■
Only open and close the door when there is no one in the opening/closing
range – risk of injury!
■
An opened door can close automatically if there is a strong wind or the
vehicle is on an incline – risk of injury!
■
Never drive with the doors open - there is a risk of death!
Door opening lever
Fig. 27
Door opening lever
Read and observe and on page 40 first.
On vehicles without central locking, you can lock and unlock doors which do
not have a locking cylinder from the inside.
Locking
›
Push the door opening lever in the direction of the arrow so that the red
marking
A
» Fig. 27 is visible.
Unlocking
›
Open the door by pulling the door opening lever once against the direction of
the arrow » Fig. 27 .
Safe securing system
Read and observe
and on page 40 first.
The door locks are blocked automatically if the vehicle is locked from the out-side. The vehicle can not be opened from the inside any more.
You will be informed that the safelock system has been activated after the ve-
hicle has been locked by means of the message   on the instrument
cluster display.
Switching off
The safelock can be switched off by locking twice within 2 seconds.
If the vehicle is locked and the safe securing system is switched off, the door
can be opened separately from the inside by a single pull on opening lever.
Switching on
The safelock switches on automatically the next time the vehicle is locked and
unlocked.
Switch-off display
The indicator light in the driver door flashes for about 2 seconds fast, goes out
and starts to flash at longer intervals after about 30 seconds.
Switch-on display
The warning light flashes for around 2 seconds in quick succession, afterwards
it begins to flash evenly at longer intervals.WARNINGIf the car is locked and the safe securing system activated, no people must
remain in the car as it will then not be possible to either unlock a door or
open a window from the inside. The locked doors make it more difficult for
rescuers to get into the vehicle in an emergency – risk to life!
Note
This function only applies to certain countries.42Using the system