2014 Peugeot RCZ service indicator

61
22 26
56 208, 209
105 147
208, 209
FAMILIARISATION
RCZ_EN_CHAP00B_PRISE EN MAIN_ED02-2013
MONITORING
The instrument panel has permanent back-
lighting for improved visibility in all situations,
both day and night.
- With the ignition on, the fuel gauge needle should indicate the level of fuel remaining.
- With the engine running, its associated low level warning lamp should go off.
- With the ignition on, the oil level indicator should display "OK" or "correct",
depending on version, for a few seconds.
If the levels are not correct, top up the levels
which are low.
INSTRUMENT PANEL
- With the ignition on, the orange and red warning lamps come on.
- With the engine running, these warning lamps should go off.
If warning lamps remain on, refer to the page
concerned.
WARNING LAMPS
Illumination of the indicator lamp indicates the
status of the corresponding function.
A. Emergency call.
SWITCH PANEL
B. Deactivation of the interior volumetric and anti-tilt sensors (alarm).
C. Central locking.
D. Deactivation of the DSC/ASR system.
E. Deactivation of the front and rear parking sensors.
F. Access to PEUGEOT services.

22
PETROL - DIESEL MANUAL
OR AUTOMATIC GEARBOX
INSTRUMENT PANELS DIALS
1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2. Coolant temperature.
Indicates the temperature of the engine coolant (°Celsius).
3. Fuel level.
Indicates the quantity of fuel remaining in the tank.
4. Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
5. Small display screen.
6. Central display screen.
7. Display management button.
Starts a manual CHECK.
Recalls the service information.
Resets the selected function to zero (trip distance recorder or service indicator).
8. Lighting dimmer button.
Adjusts the brightness of the lighting of the instruments and controls.
With large central display screen
Panel grouping together the vehicle operation indication dials and
warning lamps, with permanent back-lighting.
For more information, refer to the paragraph relating to the button
or function and its associated display.
With small central display screen

1/
MONITORING
DISPLAYS
* According to engine.
** Only on the large central display screen.
***
Only on the large central display screen with PEUGEOT Connect Media (NG4 3D).
Small display screen
A. Trip distance recorder.
(miles or km)
B. Distance recorder.
(miles or km)
C. Service spanner, if a service is due shortly or is overdue.
Central display screen
D. Speed limiter
(mph or km/h) or
Cruise control.
E. Indication of:
- a gear change * ,
or
- the programme or gear (automatic gearbox).
F. Engine oil level indicator,
service indicator.
(miles or km)
These two functions are displayed when the ignition is switched on, then disappear after a few seconds.
Warning and status indicator lamps / CHECK.

Trip computer.
Vehicle speed repeat ** .
Alert messages *** .
Vehicle parameters *** .
Navigation - Guidance *** .
These functions are displayed according to the selection.

1/
MONITORING
COOLANT TEMPERATURE INDICATOR
With the engine running, when the needle is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too high; the maximum temperature warning lamp and the central STOP warning lamp come on,
accompanied by an audible signal and an alert message in the
screen.
You MUST stop as soon as it is safe to do so.
Wait a few minutes before switching off the engine.
Contact a PEUGEOT dealer or a qualifi ed workshop.
ENGINE OIL LEVEL INDICATOR
This information is displayed for a few seconds when the ignition is
switched on, at the same time as the service information.
The check of this level is only valid if the vehicle is on a level
surface, with the engine having been off for more than 30 minutes.
After driving for a few minutes, the temperature and pressure in the
cooling system increase.
To top up the level:
 wait for the engine to cool,
 unscrew the cap by two turns to allow the pressure to drop,
 when the pressure has dropped, remove the cap,
 top up the level to the "MAX" mark.

34
Oil level correct
This is indicated by the fl ashing of "OIL" or an alert message in the
instrument panel, accompanied by illumination of the service warning
lamp and an audible signal.
If the lack of oil is confi rmed by a check using the dipstick, it is essential
that the level is topped up to prevent damage to the engine.
Refer to the "Checking levels" section. This is indicated by the fl ashing of
"OIL--" or the appearance of an alert
message in the instrument panel.
Contact a PEUGEOT dealer or a qualifi ed workshop.
In the event of a fault with the electric gauge, the oil level is no lon\
ger
monitored.
If the system is faulty, you should check the engine oil level using the
dipstick under the bonnet.
Refer to the "Checking levels" section.
Lack of oil Indicator fault

1/
MONITORING

SERVICE INDICATOR
This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indica\
tor
zero reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service.
More than 1 800 miles (3 000 km) remain before the next service is due\

When the ignition is switched on, no service information appears on the \
instrument panel central screen.
Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
For 7 seconds after the ignition is switched on, the spanner symbolising\

the service operations comes on. The instrument panel central screen
indicates the distance remaining before the next service is due.
Example: 1 700 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:
Less than 600 miles (1 000 km) remain before the next service is due
Example: 500 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates: The spanner remains on in the small screen
to indicate that a service must be carried out
soon.

36
Service overdue
For 7 seconds after the ignition is switched on, the spanner fl ashes to
indicate that the service must be carried out as soon as possible.
Example: the service is overdue by 300 miles.
For 7 seconds after the ignition is switched on, the central screen
indicates:
The spanner remains on in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the type of motoring the vehicle is used for.
Therefore, the spanner may also come on if you have exceeded
the period since the last service specifi ed in the warranty and
maintenance record.
Service indicator zero reset
Retrieving the service information
You can access the service information at any time.
This information appears when running through the manual check
procedure.
 Briefl y press the "CHECK/000" button.
The service information is displayed for a few seconds on the instrument panel central screen, then disappears.
Following this operation, if you wish to disconnect the battery, lock
the vehicle and wait at least fi ve minutes for the zero reset to be
registered.
After each service, the service indicator must be reset to zero.
The procedure for resetting to zero is as follows:
 switch off the ignition,
 press and hold the
"CHECK/000" button,
 switch on the ignition; the distance recorder display begins a countdown,
 when the instrument panel central screen indicates "=0" , release
the button; the spanner disappears from the small screen.

2/
ACCESS
ALARM *
System which protects and provides a deterrent against theft and
break-ins. It provides the following types of monitoring.
- exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a door, the boot, the
bonnet...
- interior volumetric
The system checks for any variation in the volume in the passenger compa\
rtment.
The alarm is triggered if anyone breaks a window, enters the passenger
compartment or moves inside the vehicle.
- tilt
The system checks for any change in the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted, moved or knocked. For all work on the alarm system, contact a PEUGEOT dealer or a
qualifi ed workshop.
LOCKING THE VEHICLE WITH FULL ALARM
SYSTEM
Activation
 Switch off the ignition and get out of the vehicle.
 Press the locking button on the remote control.
The monitoring system is active: the indicator lamp in the button fl ashes
once per second.
After the locking button on the remote control is pressed, the exterior \
perimeter monitoring is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after a delay of 45 seconds\
.
Deactivation
 Press the unlocking button on the remote control.
The alarm system is deactivated: the indicator lamp in the button goes o\
ff.
Self-protection function
The system checks for the putting out of service of its
components.
The alarm is triggered if the battery, the central control or the siren
wiring are put out of service or damaged.
* According to country. If an opening (door, boot...) is not closed fully, the vehicle is not
locked but the exterior perimeter monitoring will be activated after
a delay of 45 seconds at the same time as the interior volumetric
and anti-tilt monitoring.