2014 Peugeot RCZ ignition

2/
ACCESS
ALARM *
System which protects and provides a deterrent against theft and
break-ins. It provides the following types of monitoring.
- exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a door, the boot, the
bonnet...
- interior volumetric
The system checks for any variation in the volume in the passenger compa\
rtment.
The alarm is triggered if anyone breaks a window, enters the passenger
compartment or moves inside the vehicle.
- tilt
The system checks for any change in the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted, moved or knocked. For all work on the alarm system, contact a PEUGEOT dealer or a
qualifi ed workshop.
LOCKING THE VEHICLE WITH FULL ALARM
SYSTEM
Activation
 Switch off the ignition and get out of the vehicle.
 Press the locking button on the remote control.
The monitoring system is active: the indicator lamp in the button fl ashes
once per second.
After the locking button on the remote control is pressed, the exterior \
perimeter monitoring is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after a delay of 45 seconds\
.
Deactivation
 Press the unlocking button on the remote control.
The alarm system is deactivated: the indicator lamp in the button goes o\
ff.
Self-protection function
The system checks for the putting out of service of its
components.
The alarm is triggered if the battery, the central control or the siren
wiring are put out of service or damaged.
* According to country. If an opening (door, boot...) is not closed fully, the vehicle is not
locked but the exterior perimeter monitoring will be activated after
a delay of 45 seconds at the same time as the interior volumetric
and anti-tilt monitoring.

56
LOCKING THE VEHICLE WITH EXTERIOR
PERIMETER MONITORING ONLY Deactivation of the interior volumetric and anti-tilt monitoring
 Switch off the ignition.
 Within ten seconds, press the button until the indicator lamp is on continuously.
 Get out of the vehicle.
 Press the locking button on the remote control immediately.
The exterior perimeter monitoring alone is activated: the indicator lamp\

in the button fl ashes once per second.
Reactivation of the interior volumetric and anti-tilt monitoring
 Press the unlocking button on the remote control to deactivate the exterior perimeter monitoring.
 Press the locking button on the remote control to activate all the monitoring functions.
The indicator lamp in the button again fl ashes once per second.
Deactivate the interior volumetric and anti-tilt monitoring to avoid
unwanted triggering of the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea. To be effective, this deactivation must be carried out each time the
ignition is switched off.

2/
ACCESS
OPERATING FAULT LOCKING THE VEHICLE WITHOUT ACTIVATING
THE ALARM
 Lock or deadlock the vehicle using the key in the driver's door lock.
When the ignition is switched on, fi xed illumination of the indicator lamp
in the button indicates a fault with the system.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
FAILURE OF THE REMOTE CONTROL
To deactivate the monitoring functions:
 unlock the vehicle using the key in the driver's door lock,
 open the door; the alarm is triggered,
 switch on the ignition; the alarm stops; the indicator lamp in the button goes off.
TRIGGERING OF THE ALARM
The monitoring functions remain active until the alarm has been
triggered eleven times in succession.
When the vehicle is unlocked using the remote control, rapid
fl ashing of the indicator lamp in the button informs you that the
alarm was triggered during your absence. When the ignition is
switched on, this fl ashing stops immediately.
This is indicated by sounding of the siren and fl ashing of the direction
indicators for thirty seconds.
2 minutes after closing the last door or the boot, the system is activat\
ed
automatically.
 To avoid triggering the alarm when entering the vehicle, fi rst press the remote control unlocking button.
AUTOMATIC ACTIVATION *
* Depending on country of sale.

58
ELECTRIC WINDOWS
Fitted with a safety anti-pinch system.
A. Left-hand electric window.
B. Right-hand electric window.
ONE-TOUCH ELECTRIC WINDOWS
There are two options:
- manual mode  Press or pull the switch gently. The window stops when the switch is released.
- automatic mode  Press or pull the switch fi rmly. The window opens or closes fully when the switch is released.
 Pressing the switch again stops the movement of the window. The electric window switches remain operational for approximately
45 seconds after the ignition is switched off or until the vehicle is
locked after a door is opened.
If the passenger's window cannot be operated from the driver's
door control panel, carry out the operation from the control panel
of the passenger door.
After approximately ten consecutive complete opening/closing
movements of the window, a protection function is activated which
only authorises closing of the windows, so as to prevent damage
to the electric window motor.
Once the window is closed, the switches will become operational
again after approximately 40 minutes.
Safety anti-pinch
When the window rises and meets an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for example, in the presence of
ice), immediately after the movement is reversed:
 press and hold the switch until the window opens fully,
 then pull the switch immediately and hold it until the window closes,
 continue to hold the switch for approximately one second after the window has closed.
The safety anti-pinch function is not operational during these
operations.

2/
ACCESS
Reinitialisation
If a window does not rise automatically, after reconnecting the battery
for example, its operation must be reinitialised:
 pull the switch until the window stops,
 release the switch and pull it again until the window closes fully,
 continue to hold the switch for approximately one second after the window has closed,
 press the switch to lower the window automatically to the low position,
 when the window has reached the low position, press the switch again for approximately one second.
The safety anti-pinch function is not operational during these
operations. Always remove the key from the ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during operation of the electric
windows, you must reverse the movement of the window. To do
this, press the switch concerned.
When the driver operates the switch for the passenger's electric
window, they must ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the passengers use the electric
windows correctly.
Be aware of children when operating the windows.

62
Pressing the central locking control unlocks the vehicle.
Opening a door from the inside, when stationary, also unlocks the
vehicle, but the vehicle will be locked again when the speed exceeds
6 mph (10 km/h).
Activation / Deactivation
You can activate or deactivate this function.
 With the ignition on, press the button for more than two seconds.
A confi rmation message appears in the screen.
EMERGENCY LOCKING
To lock or unlock the doors mechanically in the event of a central
locking system failure or fl at battery.
Locking the driver's door
 Insert the key in the lock, then turn it to the right.
Unlocking the driver's door
 Insert the key in the lock, then turn it to the left.
Locking the passenger door
 Using the key, remove the black cap on the edge of the door.
 Insert the key in the cavity without forcing, then without turning it, move the the latch sideways towards the interior of the door.
 Remove the key and refi t the cap.
Unlocking the passenger door
 Pull the interior door opening control.
ANTI-INTRUSION SECURITY
This function permits automatic and simultaneous locking of the doors,
boot lid and fuel fi ller fl ap as soon as the vehicle speed exceeds 6 mph
(10 km/h).
Operation
If one of the doors is open, the automatic central locking does not take\

place.
If the boot lid is open, the automatic central locking of the doors is
active.

3/
EASE OF USE and COMFORT
FRONT SEATS
Seat with integral head restraint,consisting of a seat cushion and a sea\
t
back which can be adjusted to adapt your position for ease of driving
and comfort.
ELECTRIC ADJUSTMENTS
Forwards-backwards adjustment Seat cushion height adjustment
 Push the control forwards or rearwards to slide the seat.  Tilt the rear part of the control upwards or downwards to obtain the
required height.
The electrical functions of the seat are deactivated approximately
one minute after the ignition is switched off.
To reactivate them, switch on the ignition.
Carry out these adjustments with the engine running to avoid
discharging the battery.
Seat back angle adjustment
 Tilt the control forwards or rearwards to adjust the angle of the seat
back.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk \
of of jamming the seat caused by the presence of objects on the
fl oor behind the seat or rear passengers. If the seat jams, stop the
movement immediately.

3/
EASE OF USE and COMFORT
STORING DRIVING POSITIONS
System which takes into account the electrical settings of the driver's \
seat and the door mirrors. It enables you to store two positions using
the buttons on the side of the driver's seat.
STORING A POSITION
Using buttons M / 1 / 2
 Switch on the ignition.
 Adjust your seat and your door mirrors.
 Press button M , then press button 1 or 2 within four seconds.
An audible signal is heard indicating that the settings have been stored.
RECALLING A STORED POSITION
Storing a new position cancels the previous position.
Using button 1 or 2
 Press and hold button 1 or 2 until the audible signal is heard
indicating the end of the adjustment.
When the ignition is off, after a few consecutive position recalls,
the function will be deactivated until the engine is started, to
prevent discharging of the battery.