2014 Peugeot RCZ gearbox

6/
3
3
DRIVING
AUTOMATIC OPERATION
 Select position D for automatic changing of the six gears.
Never select position N while the vehicle is moving.
Never select positions P or R unless the vehicle is completely
stationary.
The gearbox then operates in auto-adaptive mode, without any
intervention on the part of the driver. It continuously selects the most
suitable gear according to the style of driving, the profi le of the road and
the load in the vehicle.
D and the gears selected automatically appear in succession in the
instrument panel.
For maximum acceleration without touching the lever, press the
accelerator pedal down fully (kick down). The gearbox changes down
automatically or maintains the gear selected until the maximum engine
speed is reached.
On braking, the gearbox changes down automatically to provide
effi cient engine braking.
If you release the accelerator sharply, the gearbox will not change to a
higher gear for safety reasons.
SPORT AND SNOW PROGRAMMES
These two special programmes supplement the automatic operation in
very specifi c conditions of use.
Sport programme "S"
 Press button
"S" , after starting the engine.
The gearbox automatically favours a dynamic style of driving.
S appears in the instrument panel.
Snow programme "  "
 Press button "  ", after starting the engine.
The gearbox adapts to driving on slippery roads.
This programme improves starting and drive when traction is poor.
 appears in the instrument panel.
RETURN TO AUTOMATIC OPERATION
 At any time, press the button selected again to quit the programme engaged and return to auto-adaptive mode.
MANUAL OPERATION
 Select position M for sequential changing of the six gears.
 Push the lever towards the + sign to change up a gear.
 Pull the lever towards the - sign to change down a gear.

136
It is only possible to change from one gear to another if the vehicle
speed and engine speed permit; otherwise, the gearbox will operate
temporarily in automatic mode. M and the gears engaged manually appear in succession in
the instrument panel.
If the engine speed is too low or too high, the gear selected
fl ashes for a few seconds, then the actual gear engaged is
displayed.
It is possible to change from position D (automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving very slowly, the gearbox
selects gear M1 automatically.
The sport and snow programmes do not operate in manual mode.
Invalid value during manual operation
This symbol is displayed if a gear is not engaged correctly
(selector between two positions).
STOPPING THE VEHICLE
Before switching off the engine, you can engage position P or N to
place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle. If the lever is not in position
P , when the driver's door is opened or
approximately 45 seconds after the ignition is switched off, there is
an audible signal is heard accompanied by a message.
 Return the lever to position P ; the audible signal stops and the
message disappears.
OPERATING FAULT
When the ignition is on, the illumination of this warning lamp,
accompanied by an audible signal and a message in the
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to emergency mode and is locked in
3rd gear. You may feel a substantial knock when changing from P to R
and from N to R . This will not cause any damage to the gearbox.
Do not exceed a speed of 60 mph (100 km/h), local speed restrictions
permitting.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
This warning lamp may also come on if a door is opened.
There is a risk of damage to the gearbox:
- if you press the accelerator and brake pedals at the same time,
- if you force the lever from position P to another position when
the battery is fl at.
To reduce fuel consumption during a long period stationary with
the engine running (traffi c jam, etc.), place the gear lever in
position N and apply the parking brake.

6/
DRIVING
GEAR EFFICIENCY INDICATOR
System which reduces fuel consumption by recommending the most
appropriate gear.
OPERATION
Depending on the driving situation and your vehicle's equipment, the
system may advise you to skip one (or more) gear(s). You can follow
this instruction without engaging the intermediate gears.
The gear engagement recommendations must not be considered
compulsory. In fact, the confi guration of the road, the amount of traffi c
and safety remain determining factors when choosing the best gear.
Therefore, the driver remains responsible for deciding whether or not
to follow the advice given by the system.
This function cannot be deactivated. The system adapts its gear change recommendation according
to the driving conditions (slope, load, ...) and the demands of the
driver (power, acceleration, braking, ...).
The system never suggests:
- engaging fi rst gear,
- engaging reverse gear,
The information appears in the instrument panel in the form of an arrow. Example:
- You are in third gear.
- You press the accelerator pedal.
- The system may suggest that you engage a higher gear.
With an automatic gearbox, the system is only active in manual mode.
On vehicle fi tted with a manual gearbox, the arrow may be
accompanied by the gear recommended.

6/
DRIVING
CRUISE CONTROL
System which automatically maintains the speed of the vehicle at the
value programmed by the driver, without any action on the accelerator
pedal.
The cruise control is switched off manually or by pressing the brake or
clutch pedal or on triggering of the trajectory control system for safet\
y
reasons.
Switching off the ignition cancels any programmed speed value.
STEERING MOUNTED CONTROL
The functions of this system are grouped together on the steering
mounted control.
1. Cruise control mode selection dial.
2. Speed programming / value decrease button.
3. Speed programming / value increase button.
4. Cruise control off / resume button.
The cruise control cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
You are advised to keep your feet near the pedals at all times.
The cruise control is
switched on manually: it requires a minimum
vehicle speed of 25 mph (40 km/h) and the engaging:
- of fourth gear on the manual gearbox,
- of second gear on the automatic gearbox, in sequential driving mode,
- of position D on the automatic gearbox.
It is possible to exceed the programmed speed temporarily by pressing
the accelerator pedal.
To return to the programmed speed, simply release the accelerator
pedal.

160

MANUAL GEARBOX
AUTOMATIC GEARBOX
BRAKE PADS BRAKE DISC WEAR
The gearbox does not require any maintenance (no oil
change).
Refer to the warranty and maintenance record for the details
of the level checking interval for this component.
The gearbox does not require any maintenance (no oil
change).
Refer to the warranty and maintenance record for details of
the level checking interval for this component.
Brake wear depends on the style of driving, particularly in
the case of vehicles used in town, over short distances.
It may be necessary to have the condition of the brakes
checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the brake fl uid level
indicates that the brake pads are worn. For information on checking brake disc wear, contact a
PEUGEOT dealer or a qualifi ed workshop.
Only use products recommended by PEUGEOT or products of
equivalent quality and specifi cation.
In order to optimise the operation of units as important as those
in the braking system, PEUGEOT selects and offers very specifi c
products.
After washing the vehicle, dampness, or in wintry conditions, ice
can form on the brake discs and pads: braking effi ciency may
be reduced. Make light brake applications to dry and defrost the
brakes.
PARKING BRAKE
If excessive travel or a loss of effectiveness of this system
is noticed, the parking brake must be checked, even
between two services.
Checking this system must be done by a PEUGEOT dealer
or a qualifi ed workshop.

168
CHANGING A WHEEL
Parking the vehicle
Immobilise the vehicle where it does not block traffi c: the ground
must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage fi rst
gear (position P for the automatic gearbox) to lock the wheels.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specifi c to your vehicle, it is stored in the
glove box.
Wheelbrace: for removal of the wheel fi xing
bolts.
Jack with integrated handle: for lifting the
vehicle.
TOOLS REQUIRED *
Bolt cover removal tool: for removal of the
bolt fi nishers (covers) on alloy wheels.
* Depending on the country of sale, the vehicle may be equipped with the tools needed to change a wheel and a spare wheel (see following
pages).

188
DASHBOARD FUSES
The fusebox is placed in the lower part of the dashboard (left hand sid\
e,
inside the glove box). It consists of two boxes.
Access to the fuses
 refer to the paragraph "Access to tools".
Fuse tables
Fuse N° Rating Functions
F2 30 A Locking and deadlocking earth.
F3 5 A Airbags, active bonnet and pretensioners
control unit.
F4 10 A Clutch pedal switch, electrochrome
rear view mirror, automatic gearbox,
switching and protection unit.
F5 30 A One-touch electric windows, folding
mirrors supply.
F7 5 A Front and rear courtesy lamps, map
reading lamps, sun visor lighting, glove
box lighting.
F8 20 A Audio equipment, audio/telephone,
multifunction screen, tyre under-infl ation
detection, clock,
F9 30 A 12 V socket.
F10 15 A Steering mounted controls.
F 11 15 A Low current ignition switch.
F12 15 A Instrument panel, air conditioning,
driver's seat memory unit, rain /
sunshine sensor, airbags.
Box 1

190
ENGINE COMPARTMENT FUSES
The fusebox is placed in the engine compartment near the battery (left-\
hand side).
Access to the fuses
 Unclip the cover.
 Change the fuse (see corresponding paragraph).
 When you have fi nished, close the cover carefully to assure the sealing of the fusebox.
Fuse table
Fuse N° Rating Functions
F2 15 A Horn.
F3 10 A Front wash-wipe.
F4 20 A Daytime running lamps.
F5 15 A Air fl ow sensor, coolant pump, oil pump,
thermostat, blow-by heater (petrol),
by-pass and EGR electrovalves (Diesel),
diesel heater (Diesel).
F6 10 A Steering wheel angle sensor, ABS/ESC
control unit, ESC sensor.
F7 10 A Power steering control unit, automatic
gearbox, dual function brake switch.
F8 25 A Starter motor control.
F9 10 A Diagnostic socket, directional
headlamps, particle emission fi lter pump
(Diesel).
F 11 40 A Air conditioning blower.