2014 Peugeot RCZ spare wheel

LIMIT THE CAUSES OF EXCESS
CONSUMPTION
Spread loads throughout the vehicle; place the heaviest items in the
bottom of the boot, as close as possible to the rear seats.
Limit the loads carried in the vehicle and reduce wind resistance (roof\

bars, roof rack, bicycle carrier, trailer...). Use a roof box in preference.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres and refi t your summer tyres.
OBSERVE THE RECOMMENDATIONS ON
MAINTENANCE
Check the tyre pressures regularly, when cold, referring to the label in
the door aperture, driver's side.
Carry out this check in particular:
- before a long journey,
- at each change of season,
- after a long period out of use.
Don't forget the spare wheel and the tyres on any trailer or caravan.
Have your vehicle serviced regularly (engine oil, oil fi lter, air fi lter,
passenger compartment fi lter...) and observe the schedule of
operations recommended in the warranty and maintenance record.
When refuelling, do not continue after the third cut-off of the nozzle to
avoid any overfl ow.
At the wheel of your new vehicle, it is only after the fi rst 1 800 miles
(3 000 kilometres) that you will see the fuel consumption settle down \
to a consistent average.

138
TYRE UNDER-INFLATION DETECTION
The system triggers an alert if a drop in pressure is detected in
one or more tyres.
A pressure sensor is located in the valve of a each tyres (except the
spare wheel). This system does not avoid the need to check the tyre pressures
regularly (including the spare wheel) and before a long journey.
Driving with under-infl ated tyres adversely affects road holding,
extends braking distances and causes premature tyre wear,
particularly under arduous conditions (vehicle loaded, high speed,
long journey).
System which automatically checks the pressures of the tyres while
driving.
The system continuously monitors the pressures of the four tyres, as
soon as the vehicle is moving.
Driving with under-infl ated tyres increases fuel consumption.
The tyre pressures for your vehicle can be found on the tyre
pressure label (see the "Identifi cation markings" section).
The tyre pressures must be checked when the tyres cold (vehicle
stopped for 1 hour or after driving for less then 6 miles (10 km) at
moderate speed). Otherwise, add 0.3 bar to the values indicated
on the label.
The tyre under-infl ation detection system is an aid to driving which
does not replace the need for the driver to be vigilant or to drive
responsibly.

6/
DRIVING
In the event of a problem on one of the tyres, the symbol or the
message appears, according to equipment, to identify it.
 Reduce speed, avoid sudden steering movements or harsh brake applications.
 Stop as soon as it is safe to do so.
 In the event of a puncture, use the temporary puncture repair kit or the spare wheel (according to equipment),
or
 if you have a compressor, the one in the temporary puncture repair kit for example, check the four tyre pressures when cold,
or
 if it is not possible to check the tyre pressures at the time, drive carefully at reduced speed.
UNDER-INFLATION ALERT
The alert is given by the fi xed illumination of this warning
lamp, accompanied by an audible signal, and depending on
equipment, the display of a message.
The loss of pressure detected does not always lead to visible
deformation of the tyre. Do not rely on just a visual check.
The alert is maintained until the tyre or tyres concerned is reinfl ated,
repaired or replaced.
The spare wheel (space-saver type or a steel rim) does not have a
sensor. The fl ashing and then fi xed illumination of the
under-infl ation warning lamp accompanied by the
illumination of the "service" warning lamp indicates a
fault with the system.
In this case, monitoring of the tyre pressures is not assured.
This alert is also displayed when one or more wheels is not fi tted
with a sensor (for example, a space-saver or steel spare wheel).
Go to a PEUGEOT dealer or a qualifi ed workshop to have the system
checked or, following the repair of a puncture, to have the original
wheel, equipped with a sensor, refi tted.
OPERATING FAULT

168
CHANGING A WHEEL
Parking the vehicle
Immobilise the vehicle where it does not block traffi c: the ground
must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage fi rst
gear (position P for the automatic gearbox) to lock the wheels.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specifi c to your vehicle, it is stored in the
glove box.
Wheelbrace: for removal of the wheel fi xing
bolts.
Jack with integrated handle: for lifting the
vehicle.
TOOLS REQUIRED *
Bolt cover removal tool: for removal of the
bolt fi nishers (covers) on alloy wheels.
* Depending on the country of sale, the vehicle may be equipped with the tools needed to change a wheel and a spare wheel (see following
pages).

8/
PRACTICAL INFORMATION
REMOVING A WHEEL
 Place the jack in contact with one of the two front A or rear B
locations provided on the underbody, whichever is closest to the
wheel to be changed.  Raise the vehicle until there is suffi cient space between the wheel
and the ground to admit the spare (not punctured) wheel easily.
 Remove the bolts and store them in a clean place.
 Remove the wheel.
 Remove the cover on each of the bolts using the bolt cover removal
tool.
 Fit the security socket on the wheelbrace to slacken the security bolt.
 Slacken the other bolts using the wheelbrace only.  Extend the jack until its base plate is in contact with the ground.
Ensure that the centreline of the jack base plate is directly below
the location A or B used.

8/
PRACTICAL INFORMATION
TOOLS AND SPARE WHEEL *
Depending on the country of sale, the vehicle is equipped with the tools\

needed to change a wheel and may also be equipped with a spare
wheel.
The spare wheel is stowed in a protective cover, secured to the boot
fl oor with Velcro
®.
The tools are held in a storage box under the boot fl oor.
Never drive with the rear seat folded when the
spare wheel - or a punctured wheel - is present
in the boot.
Warning marking
"Do not release the backrest of the rear seats!"
* According to country.
Access to the spare wheel *
 Open the boot lid.
 Remove the spare wheel by grasping the grip of its protective cover.
 Position the wheel vertically so as to read the warning markings.
 Remove the Velcro
® located on the tyre tread.
 Detach the straps, located on each sidewall, then slacken them.
 Remove the wheel from its protective cover.
When refi tting the wheel into its cover, place it so that the valve is
opposite the strap fi xings.

8/
PRACTICAL INFORMATION
SNOW CHAINS
Original tyre size Maximum link size.
235/45 R18 cannot be fi tted with chains
235/40 R19
225/45 R18 9 mm
For more information on snow chains, contact a PEUGEOT dealer or a
qualifi ed workshop. Use only the chains designed to be fi tted to the type of wheel fi tted to
your vehicle: The snow chains must be fi tted only to the front wheels. They
must never be fi tted to "space-saver" type spare wheels.
Take account of the legislation in force in your country on the use
of snow chains and the maximum running speed authorised.
Avoid driving on roads that have been cleared of snow, to
avoid damaging your vehicle's tyres and the road surface. It is
recommended that before you leave, you practise fi tting the snow
chains on a level and dry surface. If your vehicle is fi tted with alloy
wheels, check that no part of the chain or its fi xings is in contact
with the wheel rim.
In wintry conditions, snow chains improve traction as well as the
behaviour of the vehicle when braking.
Advice on installation
 If you have to fi t the chains during a journey, stop the vehicle on a
fl at surface on the side of the road.
 Apply the parking brake and position any wheel chocks to prevent movement of your vehicle.
 Fit the chains following the instructions provided by the manufacturer.
 Move off gently and drive for a few moments, without exceeding 30 mph (50 km/h).
 Stop your vehicle and check that the snow chains are correctly tightened.

206
IDENTIFICATION MARKINGS
Various visible markings for the identifi cation of your vehicle.
A. Vehicle identifi cation number (VIN) under the bonnet.
This number is engraved on the bodywork near the damper support.
For access to it, raise the plastic cover. C. Manufacturer's label.
The number is indicated on a self-destroying label affi xed to the
door aperture, below the door striker, on the right-hand side.
This label also indicates the unladen weight, the gross vehicle weight (GVW) and the gross train weight (GVW).
The tyre pressures must be checked when the tyres are cold, at
least once a month.
If the tyre pressures are too low, this increases fuel consumption.
B. VIN on the windscreen lower cross member.
This number is indicated on a self-adhesive label which is visible
through the windscreen. D. Tyre/paint label.

This label is affi xed to the door aperture, on the driver's side.
It bears the following information:
- the tyre infl ation pressures, laden and unladen,
- the tyre sizes,
- the infl ation pressure of the spare wheel,
- the paint colour code.