2014 Peugeot 208 light

163
7
Practical information
Changing a bulb
Front lamps
A. Model with light guide
In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of the glass of the headlamps and rear lamps is normal; it disappears after the lamps have been on for a few minutes.
The headlamps are fitted with polycarbonate glass with a protective coating:  do not clean them using a dr y or abrasive cloth, nor with a detergent or solvent product, use a sponge and soapy water or a pH neutral product,  when using a high pressure washer on persistent marks, do not keep the lance directed towards the lamps or their edges for too long, so as not to damage their protective coating and seals. Changing a bulb should only be done after the headlamp has been switched off for a few minutes (risk of serious burns).  Do not touch the bulb directly with your fingers, use a lint-free cloth. It is imperative to use only anti-ultraviolet (UV) type bulbs to avoid damaging the headlamp. Always replace a failed bulb with a new bulb with the same type and specification.
B. Model without light guide
1. Main beam headlamps (H7-55W).2. Dipped beam headlamps (H7-55W).3. Daytime running lamps / sidelamps (light emitting diodes - LEDs). 4.Direction indicators (PWY-24W). 5.Front foglamps (directional according to version) (H11-55W).
1. Main beam headlamps (H7-55W).2. Dipped beam headlamps (H7-55W).3. Daytime running lamps / sidelamps (W5-5W).4. Direction indicators (PWY-24W).5. Front foglamps (directional according to version) (H11-55W).

164
Practical information
Amber coloured bulbs, such as the direction indicators, must be replaced with bulbs of identical specifications and colour. When refitting, close the protective cover carefully to preserve the sealing of the headlamp.
Rapid flashing of the direction indicator warning lamp (right or left) indicates the failure of a bulb on that side.
Changing direction indicator bulbs
 Turn the bulb holder a quarter of a turn and extract it.  Pull out the bulb and change it. To reassemble, carry out these operations in reverse order.
C. GTi model
1. Main beam headlamps (H7-55W).2. Dipped beam headlamps (H7-55W).3. Daytime running lamps / sidelamps (light emitting diodes - LEDs).4. Direction indicators (light emitting diodes - LEDs).5. Front foglamps (directional according to version) (H11-55W).

166
Practical information
Changing front foglamp / directional lamps
 Access to the front foglamp is through the orifice below the bumper.  Disconnect the bulb holder connector by pressing on the top of the tongue.  Extract the bulb holder by pressing on the two clips clips (top and bottom).  Replace the module.
To reassemble, carry out these operations in reverse order. To obtain this module, contact a PEUGEOT dealer or a qualified workshop. You can also contact a PEUGEOT dealer or a qualified workshop for this replacement.
Changing the daytime running lamps / sidelamps (light- emitting diodes - LEDs)
For the replacement of this type of LED lamp, contact a PEUGEOT dealer or a qualified workshop.

167
7
Practical information
1. Brake lamps (P21W).2. Reversing lamps (R10W).3. Direction indicators (PY21W amber).4. Sidelamps (light emitting diodes - LEDs).
Rear lamps
5. Foglamp (P21W).
Changing integrated direction indicator side repeater bulbs
 Press the central tongue and remove the side repeater.  Pull the bulb holder out and replace the failed bulb. To reassemble, carry out these operations in reverse order. You should contact a PEUGEOT dealer or a qualified workshop for the replacement of these bulbs.
 Insert a flat screwdriver between the mirror glass and its base.  Use the screwdriver as a lever to extract the mirror glass.  Unclip the mirror shell by pressing on the two retaining clips.

168
Practical information
Changing brake lamp, reversing lamp and direction indicator bulbs
These three bulbs are changed from inside the boot:
 open the boot,  remove the access grille from the corresponding side trim panel,  slacken and remove the nut,  disconnect the lamp unit connector,  unclip the lamp unit carefully extract it pulling in line towards the outside,
 press the four tabs and remove the bulb h o l d e r,  turn the bulb a quarter of a turn and change it. To reassemble, carry out these operations in reverse order. Take care to engage the lamp unit in its guides, while keeping it in line with the vehicle. Tighten sufficiently to ensure sealing, but without damaging the lamp.
Changing the light emitting diode-LED lamps
For replacement, contact a PEUGEOT dealer or qualified workshop.

183
7
Practical information
Towing a trailer
We recommend the use of genuine PEUGEOT towbars and their harnesses that have been tested and approved from the design stage of your vehicle, and that the fitting of the towbar is entrusted to a PEUGEOT dealer or a qualified workshop. If the towbar is not fitted by a PEUGEOT dealer, it is imperative that it is fitted in accordance with the vehicle manufacturer's instructions.
Towbar suitable for the attachment of a trailer or installation of a bicycle carrier, with additional lighting and signalling.
Driving with a trailer places greater demands on the towing vehicle and the driver must take particular care.
Your vehicle is primarily designed for transporting people and luggage, but it may also be used for towing a trailer.

184
Practical information
Driving advice
Distribution of loads
 Distribute the load in the trailer so that the heaviest items are as close as possible to the axle and the nose weight approaches the maximum permitted without exceeding it.
Air density decreases with altitude, thus reducing engine performance. Above 1 000 metres, the maximum towed load must be reduced by 10 % for every 1 000 metres of altitude.
Side wind
 Take into account the increased sensitivity to side wind.
Cooling
Towing a trailer on a slope increases the temperature of the coolant. As the fan is electrically controlled, its cooling capacity is not dependent on the engine speed.
 To lower the engine speed, reduce your speed. The maximum towed load on a long incline depends on the gradient and the ambient temperature. In all cases, keep a check on the coolant temperature.
 If the warning lamp and the STOP warning lamp come on, stop the vehicle and switch off the engine as soon as possible.
Braking
Towing a trailer increases the braking distance. To avoid overheating of the brakes on a long mountain type of descent, the use of engine braking is recommended.
Ty r e s
 Check the tyre pressures of the towing vehicle and of the trailer, observing the recommended pressures.
Lighting
 Check the electrical lighting and signalling on the trailer.
The rear parking sensors will be deactivated automatically if a genuine PEUGEOT towbar is used.
Refer to the "Technical data" section for details of the weights and towed loads which apply to your vehicle.

186
Practical information
Advice on care and maintenance
Recommendations on the care and maintenance your vehicle are given in the warranty and maintenance record.
Matt paint
We recommend the use of a high pressure jet wash, or at least a water hose with a high output. We recommend that the vehicle be rinsed using de-ionised water. Use only a microfibre cloth to dry the vehicle. It must be clean and used without heavy pressure. Lightly wipe off any fuel stains present on the bodywork using a soft cloth, then leave to dry. From the range of cleaning and maintenance products in the "TECHNATURE" range recommended and approved by PEUGEOT, use only the insect remover and car shampoo, which are the only products to be used on the bodywork. The insect remover can also be used to remove
minor marks (for example: finger marks...). Always have paint repairs done by a PEUGEOT dealer or a qualified workshop.
If you vehicle is finished with a clear matt lacquer, please observe the following recommendations to avoid damaging the paintwork by the use of an inappropriate
cleaning procedures. These recommendations are also valid for alloy road wheels finished with clear matt lacquer.
Never clean the vehicle without water. Never wash your vehicle in an automatic roller brush car wash. Never polish the vehicle body, nor the alloy wheels. Doing this will make the paintwork shiny. Do not use paint cleaners, abrasive products or paint polishing or preserving products (such as wax, for example) on the paintwork. These products are only suitable for bright finishes. Application of these products on vehicles with a matt finish will seriously damage the paint sur face of the vehicle, giving rise to irreversible shiny or stained areas.
Never use a high pressure jet wash with a lance fitted with a brush, this may scratch the paintwork. Never select a wash programme that finishes with a hot wax cycle.