2014 NISSAN TEANA belt

ENGINE COOLANTCO-37
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
• Do not allow the coolant to
contact the drive belts.
• Perform this step when engine is cold.
5. When draining all of the coolant in the system for engine removal or repair, open all of the drain plugs (A-D) on the cylin-
der block.
6. Check the drained coolant for contaminants such as rust, corro- sion or discoloration.
If the coolant is contaminated, flush the engine cooling system.
REFILLING ENGINE COOLANT
1. Install the radiator drain plug. If the cooling syst em was drained completely, install the reservoir tank and
the cylinder block drain plugs.
• The radiator must be complete ly empty of coolant and water.
• Apply sealant to the threads of the cylinder block drain plug. Use Genuine High Performance
Thread Sealant or equivalent. Refer to GI-21, "Recommended Chemical Products and Sealants"
.
CAUTION:
Do not reuse copper sealing washers.
2. If disconnected, reattach the upper radiator hose at the engine side.
3. Set the vehicle heater controls to the full HOT and heat er ON position. Turn the vehicle ignition ON with
the engine OFF as necessary to activate the heater mode.
PBIC2487E
Radiator drain plug : Refer to CO-16, "Exploded View"
Cylinder block front drain plug (LH) (A) (ex-
cept Canada) : 62.0 N·m (6.3 kg-m, 46 ft-lb)
Cylinder block water drain plug (B) : 6.0 N·m (0.6 kg-m, 53 in-lb)
Cylinder block rear drain plug (C) : 78.0 N·m (8.0 kg-m, 58 ft-lb)
Cylinder block RH banjo bolt (D) (oil co oler) : 19.6 N·m (2.0 kg-m, 14 ft-lb)
Revision: November 20132014 Altima NAM

RADIATORCO-41
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
Removal and InstallationINFOID:0000000009460416
REMOVAL
1. Remove radiator cap and drain coolant from radiator. Refer to
CO-12, "Changing Engine Coolant".
CAUTION:
• Perform this step when the engine is cold.
• Do not spill coolant on the drive belt.
2. Remove front air duct. Refer to EM-29, "Removal and Installation"
.
3. Disconnect coolant reservoir hose from the radiator.
4. Remove fender protector side cover (LH/RH). Refer to EXT-26, "FENDER PROTECTOR : Exploded
View".
5. Disconnect radiator hose (upper) and radiat or hose (lower) from the radiator.
CAUTION:
Do not allow the coolant to contact the drive belt.
NOTE:
The radiator hose clamps on the radiator hose (upper ) and on the radiator hose (lower), are not serviced
separately. Radiator hose clamps are part of the radiator hose assembly and serviced as one unit with the
radiator hose.
6. Disconnect the CVT oil cooler hoses.
7. Remove the front bumper fascia. Refer to EXT-17, "Removal and Installation"
.
8. Remove A/C condenser. Refer to HA-30, "COMPRESSOR : Removal and Installation"
.
CAUTION:
Be careful not to damage condenser core.
9. Remove the radiator mounts (upper).
10. Remove radiator. CAUTION:
Do not damage or scratch the radiator core when removing.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, refill coolant and check for leaks. Refer to CO-12, "Changing Engine Coolant"
and CO-11,
"System Inspection".
CAUTION:
Do not spill coolant in engi ne compartment. Use a shop cloth to absorb coolant.
InspectionINFOID:0000000009460417
INSPECTION AFTER INSTALLATION
• Check that the reservoir tank cap is tightened.
• Check for leakage of engine coolant using Tool (B) and suitable tool (A). Refer to CO-35, "System Inspection"
.
WARNING:
Do not remove the radiator cap wh en the engine is hot. Seri-
ous burns could occur from high pressure coolant escaping
from the radiator.
CAUTION:
Higher pressure than specified may cause radiator damage.
• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid (CVT
models). Tool number : EG17650301 (J-33984-A)
Testing pressure : Refer to CO-53, "Radiator"
.
AWBIA0740ZZ
Revision: November 20132014 Altima NAM

CO-42
< REMOVAL AND INSTALLATION >[VQ35DE]
COOLING FAN
COOLING FAN
Exploded ViewINFOID:0000000009460418
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a th ick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
NOTE:
• When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from
spilling.
• Replace the radiator shroud and cooling fan assembly as a unit. Do not replace cooling fan motors or cool-
ing fan blades separately.
Removal and InstallationINFOID:0000000009460419
REMOVAL
1. Partially drain engine coolant from the radiator. Refer to CO-36, "Changing Engine Coolant".
CAUTION:
• Perform when engine is cold.
• Do not spill coolant on the drive belt.
2. Remove engine room cover. Refer to EM-28, "Removal and Installation"
.
1. Radiator core support 2. Fan shroud and motor assembly 3. Grommet
AWBIA1275GB
Revision: November 20132014 Altima NAM

CO-44
< REMOVAL AND INSTALLATION >[VQ35DE]
WATER PUMP
WATER PUMP
Exploded ViewINFOID:0000000009460420
Removal and InstallationINFOID:0000000009460421
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a th ick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
CAUTION:
• When removing water pump assembly, be car eful not to get coolant on drive belt.
• Water pump cannot be disassembled and must be replaced as a unit.
• After installing the water pump, connect hose and clamp securely, then check for leaks. Repair as
necessary.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect the negative battery terminal. Refer to PG-73, "Removal and Installation (Battery)".
2. Remove the core support cover clips (A), then remove the core support cover (1).
3. Remove front air duct. Refer to EM-84, "Removal and Installation"
.
1. Timing chain tensioner (primary) 2. Valve timing control cover gasket
(bank 1)3. Valve timing cont
rol cover (bank 1)
4. Water pump cover 5. O-ring 6. O-ring
7. Water pump A. Engine oil B. Identify with white mark
AWBIA1291GB
ALKIA2602ZZ
Revision: November 20132014 Altima NAM

WATER PUMPCO-45
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
4. Remove cowl top extension. Refer to
EXT-24, "Removal and Installation".
5. Remove the front road wheel and tire (RH). Refer to WT-55, "Adjustment"
.
6. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
7. Drain coolant from the radiator. Refer to CO-36, "Changing Engine Coolant"
.
CAUTION:
Perform when the engine is cold.
8. Disconnect coolant reservoir hose and remove coolant reservoir tank. Refer to CO-40, "Exploded View"
.
9. Drain the power steering fluid reservoir. Refer to ST-30, "Draining and Refilling"
.
10. Remove the power steering oil pump. Refer to ST-38, "Removal and Installation"
.
11. Support engine and remove the RH engine insulator and bracket. Refer to EM-220, "Exploded View"
.
12. Set No. 1 cylinder at TDC on its compression stroke. • Align pointer with TDC mark on crankshaft pulley.
13. Remove drive belt. Refer to EM-134, "Removal and Installation"
.
14. Remove the drive belt auto-tensioner assembly. Refer to EM-135, "Removal and Installation of Drive Belt
Auto-tensioner".
15. Remove water drain plug (A) and copper sealing washer (B) to drain coolant from engine.
CAUTION:
Do not reuse copper sealing washers.
16. Disconnect RH valve timing control connectors and remo ve valve timing control cover (bank 1). Refer to
EM-182, "Exploded View"
.
17. Remove water pump cover. Refer to CO-44, "Exploded View"
.
18. Remove the timing chain tensioner (primary) as follows:
a. Pull the lever (C) down to release the plunger stopper tab (B).
b. Insert the stopper pin A into the tensioner body hole to hold the lever (C) and keep the plunger stopper tab (B) released.
NOTE:
An allen wrench [(1.2 mm (0.047 in)] is used for a stopper pin A
as an example.
c. Compress the plunger (D) into the tensioner body (1) by press- ing the slack guide (2).
d. Keep the slack guide (2) pressed and lock the plunger (D) in by pushing the stopper pin A through the lever (C) and into the
chain tensioner body hole.
e. Remove timing chain tensioner bolts and then remove the timing chain tensioner. CAUTION:
Be careful not to drop timing chain te nsioner bolts inside timing chain case.
19. Remove the three water pump bolts (A). Make a gap between water pump sprocket (1) and timing chain, by carefully turning
crankshaft pulley (2) counterclockwise until timing chain loosens
on water pump sprocket (1).
: Front
AWBIA1202GB
AWBIA0903ZZ
AWBIA0904ZZ
Revision: November 20132014 Altima NAM

DAS-1
CRUISE CONTROL & DRIVER ASSISTANCE
C
D E
F
G H
I
J
K L
M B
DAS
SECTION DAS
N
P
A
CONTENTS
DRIVER ASSISTANCE SYSTEM
ITS CONTROL UNIT
PRECAUTION ................ ...............................
8
PRECAUTIONS .............................................. .....8
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
8
Precautions For Harness Repair ...............................8
SYSTEM DESCRIPTION . .............................9
COMPONENT PARTS ................................... .....9
Component Parts Location .................................. ......9
Component Description ...........................................10
SYSTEM .............................................................11
System Description ............................................. ....11
Fail-safe (ITS Control Unit) .....................................13
DIAGNOSIS SYSTEM (ITS CONTROL UNIT) ....14
CONSULT Function (AVM) ................................. ....14
ECU DIAGNOSIS INFORMATION ..............17
ITS CONTROL UNIT ...................................... ....17
Reference Value ................................................. ....17
Fail-safe ..................................................................19
DTC Inspection Priority Chart ............................. ....19
DTC Index ........................................................... ....20
WIRING DIAGRAM ......................................22
DRIVER ASSISTANCE SYSTEMS ................ ....22
Wiring Diagram ................................................... ....22
BASIC INSPECTION ...................................31
DIAGNOSIS AND REPAIR WORK FLOW .... ....31
Work Flow ........................................................... ....31
Diagnostic Work Sheet ............................................32
PRE-INSPECTION FOR DIAGNOSIS ................34
Inspection Procedure ........................................... ....34
ACTION TEST ...................................................35
Description ...............................................................35
Inspection Procedure ...............................................35
ADDITIONAL SERVICE WHEN REPLACING
REAR VIEW CAMERA ......................................
37
Description ........................................................... ....37
Work Procedure .......................................................37
REAR VIEW CAMERA CALIBRATION ............38
Description ...............................................................38
Work Procedure (Preparation) .................................38
Work Procedure (Target Setting) .............................39
Work Procedure (Rear View Camera Calibration) ....40
DTC/CIRCUIT DIAGNOSIS .........................42
C1A03 VEHICLE SPEED SENSOR ..................42
DTC Logic ............................................................ ....42
Diagnosis Procedure ...............................................42
C1A04 ABS/TCS/VDC SYSTEM ......................43
DTC Logic ................................................................43
Diagnosis Procedure ...............................................43
C1A39 STEERING ANGLE SENSOR ..............44
DTC Logic ................................................................44
Diagnosis Procedure ...............................................44
U0122 VDC P-RUN DIAG .................................45
DTC Logic ............................................................ ....45
Diagnosis Procedure ...............................................45
U0416 VDC CHECKSUM DIAG ........................46
DTC Logic ................................................................46
Diagnosis Procedure ...............................................46
U0428 STEERING ANGLE SENSOR ...............47
DTC Logic ................................................................47
Diagnosis Procedure ...............................................47
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-2
U1000 CAN COMM CIRCUIT ............................48
Description ........................................................... ...48
DTC Logic ...............................................................48
Diagnosis Procedure ..............................................48
U1010 CONTROL UNIT (CAN) .........................49
Description ........................................................... ...49
DTC Logic ...............................................................49
Diagnosis Procedure ..............................................49
U111A REAR CAMERA IMAGE SIGNAL CIR-
CUIT ................................................................ ...
50
DTC Logic ............................................................ ...50
Diagnosis Procedure ..............................................50
U1232 STEERING ANGLE SENSOR ................52
DTC Logic ............................................................ ...52
Diagnosis Procedure ..............................................52
U1305 CAMERA IMAGE CALIB .......................53
DTC Logic ............................................................ ...53
Diagnosis Procedure ..............................................53
U1308 CAMERA CONFIG .................................54
DTC Logic ............................................................ ...54
Diagnosis Procedure ..............................................54
U1309 PUMP UNIT CURRENT .........................55
DTC Logic ............................................................ ...55
Diagnosis Procedure ..............................................55
U130B REAR CAMERA COMM ERROR ..........58
DTC Logic ............................................................ ...58
Diagnosis Procedure ..............................................58
U1310 PUMP UNIT CIRCUIT ............................59
DTC Logic ............................................................ ...59
Diagnosis Procedure ..............................................59
POWER SUPPLY AND GROUND CIRCUIT .....62
Diagnosis Procedure ........................................... ...62
WARNING SYSTEMS SWITCH CIRCUIT .........63
Component Function Check ................................ ...63
Diagnosis Procedure ..............................................63
Component Inspection ............................................64
WARNING SYSTEMS ON INDICATOR CIR-
CUIT ................................................................ ...
65
Component Function Check ................................ ...65
Diagnosis Procedure ..............................................65
Component Inspection ............................................66
WARNING BUZZER CIRCUIT ...........................67
Component Function Check ................................ ...67
Diagnosis Procedure ..............................................67
REMOVAL AND INSTALLATION ...............68
ITS CONTROL UNIT ....................................... ...68
Removal and Installation ..................................... ...68
REAR VIEW CAMERA ......................................69
Exploded View ..................................................... ...69
Removal and Installation .........................................69
REAR VIEW CAMERA WASHER CONTROL
UNIT ................................................................ ...
70
Exploded View ..................................................... ...70
Removal and Installation .........................................70
REAR VIEW CAMERA AIR PUMP MOTOR .. ...71
Exploded View ..................................................... ...71
Removal and Installation .........................................71
LDW
PRECAUTION ........ ....................................
72
PRECAUTIONS .............................................. ...72
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. ...
72
Precaution for Work ................................................72
Precautions For Harness Repair .............................72
Precaution for LDW System Service .................... ...73
PREPARATION ..........................................74
PREPARATION .............................................. ...74
Special Service Tool ............................................ ...74
SYSTEM DESCRIPTION ...........................75
COMPONENT PARTS .................................... ...75
Component Parts Location .................................. ...75
Component Description ..........................................76
SYSTEM ............................................................77
System Description .............................................. ...77
Fail-safe (ITS Control Unit) .....................................79
Fail-safe (Rear View Camera) ................................79
OPERATION ......................................................80
Switch Name and Function .................................. ...80
Menu Displayed by Pressing Each Switch ..............80
HANDLING PRECAUTION ............................ ...82
Precautions for Lane Departure Warning ............ ...82
DIAGNOSIS SYSTEM (ITS CONTROL UNIT) ...83
CONSULT Function (AVM) .................................. ...83
ECU DIAGNOSIS INFORMATION .............86
ITS CONTROL UNIT .........................................86
Reference Value .................................................. ...86
Fail-safe ..................................................................88
DTC Inspection Priority Chart .............................. ...88
DTC Index ............................................................ ...89
WIRING DIAGRAM ....................................91
DRIVER ASSISTANCE SYSTEMS ................ ...91
Wiring Diagram .................................................... ...91
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-4
LDW SYSTEM SETTINGS CANNOT BE
TURNED ON/OFF IN VEHICLE INFORMA-
TION DISPLAY ............................................... .
140
Description ........................................................... ..140
Diagnosis Procedure .............................................140
NORMAL OPERATING CONDITION ..............141
Description ........................................................... ..141
REMOVAL AND INSTALLATION ..............142
WARNING SYSTEMS SWITCH ..................... .142
Removal and Installation ..................................... ..142
REAR VIEW CAMERA ....................................143
Exploded View ..................................................... ..143
Removal and Installation .......................................143
REAR VIEW CAMERA WASHER CONTROL
UNIT ................................................................ .
144
Exploded View ..................................................... ..144
Removal and Installation .......................................144
REAR VIEW CAMERA AIR PUMP MOTOR ...145
Exploded View ..................................................... ..145
Removal and Installation .......................................145
BSW
PRECAUTION .............. ..............................
146
PRECAUTIONS .............................................. .146
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. ..
146
Precaution for Work ...............................................146
Precautions For Harness Repair ...........................146
Precaution for BSW System Service .....................147
PREPARATION ..........................................148
PREPARATION .............................................. .148
Special Service Tool ............................................ ..148
SYSTEM DESCRIPTION ...........................149
COMPONENT PARTS .................................... .149
Component Parts Location .................................. ..149
Component Description .........................................150
SYSTEM .......................................................... .152
System Description .............................................. ..152
Fail-safe (ITS Control Unit) ....................................154
OPERATION ................................................... .155
Switch Name and Function .................................. ..155
System Display and Warning ................................155
HANDLING PRECAUTION ..............................157
Precautions for Blind Spot Warning ..................... ..157
DIAGNOSIS SYSTEM (ITS CONTROL UNIT) .158
CONSULT Function (AVM) ................................. ..158
ECU DIAGNOSIS INFORMATION ............161
ITS CONTROL UNIT ........................................161
Reference Value .................................................. .161
Fail-safe ................................................................163
DTC Inspection Priority Chart .............................. .163
DTC Index ............................................................ .164
WIRING DIAGRAM ...................................166
DRIVER ASSISTANCE SYSTEMS ................ ..166
Wiring Diagram .................................................... .166
BASIC INSPECTION .................................175
DIAGNOSIS AND REPAIR WORK FLOW ..... ..175
Work Flow ............................................................ .175
Diagnostic Work Sheet .........................................176
PRE-INSPECTION FOR DIAGNOSIS ..............178
Inspection Procedure ........................................... .178
ACTION TEST ..................................................179
Description ........................................................... .179
Inspection Procedure ............................................179
ADDITIONAL SERVICE WHEN REPLACING
REAR VIEW CAMERA ................................... ..
181
Description ........................................................... .181
Work Procedure ....................................................181
REAR VIEW CAMERA CALIBRATION ...........182
Description ........................................................... .182
Work Procedure (Preparation) ..............................182
Work Procedure (Target Se tting) ..........................183
Work Procedure (Rear View Camera Calibration) .184
DTC/CIRCUIT DIAGNOSIS .......................186
C1A03 VEHICLE SPEED SENSOR .................186
DTC Logic ............................................................ .186
Diagnosis Procedure .............................................186
C1A04 ABS/TCS/VDC SYSTEM ......................187
DTC Logic ............................................................ .187
Diagnosis Procedure .............................................187
C1A39 STEERING ANGLE SENSOR ..............188
DTC Logic ............................................................ .188
Diagnosis Procedure .............................................188
U0122 VDC P-RUN DIAG .................................189
DTC Logic ............................................................ .189
Diagnosis Procedure .............................................189
U0416 VDC CHECKSUM DIAG .......................190
DTC Logic ............................................................ .190
Diagnosis Procedure .............................................190
U0428 STEERING ANGLE SENSOR ..............191
DTC Logic ............................................................ .191
Diagnosis Procedure .............................................191
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM