2014 MITSUBISHI MIRAGE reset

3-100 Features and controls
3
Odometer
N00574900016
The odometer indicates the total distance the vehicle has trav-
eled.Trip odometer
N00575000014
The trip odometer indicates the distance traveled between two
points.To reset the trip odometerTo return the display to 0, hold down the multi-information dis-
play switch for about 1 second or more. Only the currently dis-
played value will be reset.
Example
If trip odometer is displayed, only trip odometer will
be reset.NOTE
Both trip odometers and can count up to 9999.9
miles/kilometers.
When a trip odometer goes past 9999.9 miles/kilometers,
it returns to 0.0 miles/kilometers.

When disconnecting the battery terminal, the memories of
trip odometer displays and are cleared, and their
displays return to “0.0 miles/kilometers”.
Instrument panel light dimmer control
N00575100015
Each time you press the multi-information display switch (2),
there is a sound and the brightness of the instrument panel
lights changes.
Usage examples for trip odometer , trip odometer
It is possible to measure two currently traveled distances,
from home using trip odometer and from a particular
point on the way using trip odometer .
1- Brightness level
2- Multi-information display switch
Bright Dim
BK0162600US.book 100 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-102 Features and controls
3
Average fuel consumption display
N00575300017
This displays the average fuel consumption from the last reset
to the present.
The reset mode conditions for the average fuel consumption
display can be switched between “Auto reset” and “Manual
reset”.
For information on how to change the average fuel consump-
tion display setting, refer to “Changing the function settings”
on page 3-105.NOTE
The average fuel consumption display can be reset sepa-
rately in both auto reset mode and manual reset mode.

“---” is displayed when the average fuel consumption can-
not be measured.

The initial (default) setting is “Auto reset mode”.

Average fuel consumption may vary depend on the driv-
ing conditions (road conditions, how you drive, etc.).
The actual fuel consumption may differ from the fuel con-
sumption displayed, so treat the fuel consumption dis-
played as just a rough guideline.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The display setting can be changed to the preferred units
{mpg, km/L, L/100 km}.
Refer to “Changing the function settings” on page 3-105.
Fuel remaining display
N00575400018
The fuel remaining display indicates the fuel level in the fuel
tank when the ignition switch or the operation mode in ON.NOTE
It may take several seconds to stabilize the display after
refilling the tank.

If fuel is added with the ignition switch or the operation
mode in ON, the remaining fuel display may incorrectly
indicate the fuel level.

The fuel lid mark (A) indicates that the fuel tank filler
door is located on the left side of the vehicle. (Refer to
“Filling the fuel tank” on page 1-4.)1- Full
0- Empty
BK0162600US.book 102 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-104 Features and controls
3
2. This informs you that a periodic inspection is due. Contact
an authorized Mitsubishi Motors dealer or a repair facility
of your choice to have the system checked.
3. After your vehicle is inspected at an authorized Mitsubishi
Motors dealer, it displays the time until the next periodic
inspection.To resetThe “---” display can be reset while the ignition switch or the
operation mode is in OFF.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the service reminder display.2. Press and hold the multi-information display switch for
about 1 second or more to make the spanner mark start
flashing. (If there is no operation for about 10 seconds
with flashing, the display will revert to its original indica-
tion.)
3. With this indicator flashing, if you lightly press the multi-
information meter switch, the display switches from “---”
to “cLEAr”. After that, the time until the next periodic
inspection is shown.BK0162600US.book 104 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-105
3
NOTE
The “---” display cannot be reset while the ignition switch
or the operation mode is in ON.

When “---” is displayed, after a certain distance and a cer-
tain period of time, the display is reset and the time until
the next periodic inspection is displayed.

If you accidentally reset the display, consult an authorized
Mitsubishi Motors dealer for assistance.
Changing the function settings
N00556800143
When the ignition switch or the operation mode is in ON, the
fuel consumption unit, displayed in the multi-information dis-
play, and the average fuel consumption reset mode can be mod-
ified as desired.Changing the reset mode for average fuel consumption
N00575500019
You can change the mode condition for the average fuel con-
sumption display to “Auto reset” or “Manual reset”.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the driving range display.
Refer to “Information display” on page 3-99.
CAUTION
!
The customer is responsible for making sure that
regular inspections and maintenance and periodic
inspections and maintenance are performed.
Inspections and maintenance must be performed to
prevent accidents and malfunctions.
CAUTION
!
The driver should not operate the display while the
vehicle is in motion.
When operating the system, stop the vehicle in a safe
area.
BK0162600US.book 105 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-106 Features and controls
3
2. Each time you press the multi-information display switch
for 1 second or more on driving range display, you can
switch reset mode for average fuel consumption.
(A: Auto reset mode, B: Manual reset mode)Manual reset mode

When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.

When the following operation is performed, the mode set-
ting changes automatically from manual to auto.
[Except for vehicles equipped with the F.A.S.T.-key]
Turn the ignition switch to the “ON” position from the
“ACC” or “OFF” position.
[For vehicles equipped with the F.A.S.T.-key]
Change the operation mode to ON from ACC or OFF.
Auto reset mode Manual reset mode
BK0162600US.book 106 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-107
3
Auto reset mode

When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.

When the engine switch or the operation mode is in the
following conditions, the average fuel consumption dis-
play will automatically reset.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch has been set to the “ACC” or “OFF”
position for about 4 hours or more.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode has been set to ACC or OFF for about
4 hours or more.NOTE
The average fuel consumption display can be reset sepa-
rately for the auto reset mode and for the manual reset
mode.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The initial (default) setting is “Auto reset mode”.
Changing the fuel consumption display unit
N00557100156
The fuel consumption display unit can be changed. The dis-
tance and amount units are also switched to match the selected
fuel consumption unit.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the average fuel consumption display.
Refer to “Information display” on page 3-99.
2. Press and hold the multi-information display switch for
about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi-information display switch to
switch in sequence from “km/L” → “L/100 km” →
“mpg” → “km/L”.
BK0162600US.book 107 ページ ２０１３年３月２２日　金曜日　午後２時４１分

5-32 Comfort controls
5
To listen to the radio
N00735000926
1. Press the PWR switch or the RADIO button to turn on the
radio.
Press and hold the PWR switch for 2 seconds or longer to
turn off the radio.
2. Press the RADIO button to select the desired band
(AM/FM1/FM2).
3. Press the seek button to tune to a station, or press one of
the memory select buttons to tune in to a station memo-
rized for that button.
Refer to “Automatic tuning”, “Manual tuning” or “To
enter frequencies into the memory”.To tune the radioManual tuning
The frequency changes every time the seek button is pressed.
Press the button to select the desired station.
Automatic tuning
After keeping the seek button depressed until it beeps, release
the button, and the selected station reception will start.
To enter frequencies into the memoryAs many as 6 AM and 12 FM stations can be entered into the
memory.
To store a frequency in the memory, follow these steps:
1. Press the seek button to tune to the frequency you wish to
keep in the memory.
2. Press one of the memory select buttons until it beeps.
The sound will be momentarily interrupted while the fre-
quency is being entered into the memory. The number of
the button matching the entry in the memory as well as the
frequency is displayed.
3. The preset memory setting is retrieved by pressing the
button and then releasing it within 1 second.
BK0162600US.book 32 ページ ２０１３年３月２２日　金曜日　午後２時４１分

5-40 Comfort controls
5
NOTE
Reset the time after the battery terminals are disconnected
and reconnected.

Seconds do not appear in the clock display, but after
adjusting the “minutes” setting, the clock begins to oper-
ate from 0 seconds.
To confirm the version number of the Gracenote
DB (vehicles with a Bluetooth
® 2.0 interface)
N00702800012
1. Press and hold the /MENU button until you hear a
beep. “GracenoteDB” will appear on the display.
Each time the /MENU button is pressed, this switches
in the order Gracenote DB, PHONE SET and cancel.
2. Press the or buttons several times to select “DB
Version” and then press the /MENU button to deter-
mine.
The Gracenote DB version is displayed.A-
/MENU button
B-
button
C-
button
BK0162600US.book 40 ページ ２０１３年３月２２日　金曜日　午後２時４１分