2014 MITSUBISHI L200 isofix

WARNINGlWhen the child restraint system is not in
use, keep your child restraint system se-
cured with the seat belt or remove it from
the vehicle in order to prevent it from be-
ing thrown around inside the vehicle dur-
ing an accident.
NOTE
l Depending on the seating position in the ve-
hicle and the child restraint system that you
have, the child restraint can be attached us-
ing one of the following two locations: •To the lower anchorage in the rear seat
ONLY if the child restraint has ISOFIX
mountings (Double cab, See page 2-24).
• To the seat belt (See page 2-25).
Older children E00406700235
Children who have outgrown the child restraint sys-
tem should be seated in the rear seat and wear com-
bination lap shoulder belt.
The lap portion of the belt should be snug and posi-
tioned low on the abdomen so that it is below the
top of the hip-bone. Otherwise, the belt could in-
trude into the child’s abdomen during an accident
and cause injury.
WARNINGl Children who are not buckled up can be
thrown out of the vehicle in an accident.WARNINGl Children who are not buckled up can
strike other people in the vehicle in an ac-
cident.
l A child should never be left unattended
in your vehicle. When you leave the vehi-
cle, take the child with you.
Seat and seat belts
2-15
OKTE14E2
2

Suitability for various ISOFIX positionsE00411400692Mass groupSize classFixtureVehicle ISOFIX positionsRear Outboard (Double cab)CarrycotFISO/L1XGISO/L2X0- Up to 10 kgEISO/R1X0+- Up to 13 kgEISO/R1IL*1DISO/R2XCISO/R3XI-9 to 18 kgDISO/R2XCISO/R3XBISO/F2IUFB1ISO/F2XIUF, IL* 2AISO/F3IUFII-15 to 25 kg XIII-22 to 36 kg XCAUTIONl
When installing a child restraint system, remove the head restraint from the seat.Key of letters to be inserted in the table above:
lIUF- Suitable for ISOFIX forward child restraints systems of universal category approved for use in the mass group.
l IL- Suitable for particular ISOFIX child restraint systems given in the following list (MITSUBISHI MOTORS GENUINE parts).
l X- ISOFIX position not suitable for ISOFIX child restraint systems in this mass group and/or this size class.
Seat and seat belts
2-16
OKTE14E2
2

IL (Genuine part information) Genuine part No.ECE No.*1MZ314393 (Child restraint system),
MZ314394 (ISOFIX base)E1-04301146*2MZ313045E1-04301133
NOTE
l MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.
Seat and seat belts
2-17
OKTE14E2
2

Installing a child restraint system to
the lower anchorage (ISOFIX child re-
straint mountings)* E00408900114
Your vehicle’s second seat is fitted with lower an-
chorages for attaching a child restraint system with
ISOFIX mountings.Child restraint system with ISOFIX
mountings E00409000574
The child restraint system is designed only for
seats that incorporate lower anchorages. Retain the
child restraint system using the lower anchorages.
It is not necessary to retain the child restraint sys-
tem using the vehicle’s seat belts.
A- Child restraint system connectors
To install
WARNINGl If there is any foreign material in or
around the connectors, remove it before
installing the child restraint system. Also,
make sure the seat belt is away from, not
looped through or otherwise interfering
with, the child restraint system. If foreign
matter is not removed and/or the seat
belt interferes with the child restraint sys-
tem, the child restraint system will not be
secured properly and could move for-
ward in the event of sudden braking or a
collision, seriously injuring the child and
possibly other vehicle occupants.
l When the vehicle is moving do not adjust
the seat where the child restraint system
is installed.1. Remove the head restraint from the location
in which you wish to install a child restraint.
Refer to “Head restraints” on page 2-08.
2. Push the child restraint system’s connectors
into the lower anchorages (A) in accordance
with the instructions provided by the child re-
straint system’s manufacturer.
If your child restraint system requires the use
of a tether strap, fasten the tether strap in ac-
cordance with steps 3 through 5. If a tether
strap is unnecessary, perform the step 6.
Seat and seat belts
2-24 OKTE14E2
2