2014 MITSUBISHI iMiEV brake light

Electric power steering system (EPS)
Features and controls 5-27
5
N00531700590
Avoid hard braking and high-speed driving. Stop the vehicle in a safe place, put the selec- tor lever to the “P” (PARK) position and turn off the electric motor unit. Restart the electric motor unit and check tosee whether the light goes out after a few minutes driving; if it then remains off during driving, there is no problem.However, if the warning light does not disap- pear, or if it comes on
again when the vehicle
is driven, we recommend you to have thevehicle checked. The ABS and brake force distribution func- tion may not work, so hard braking could make the vehicle unstable.Avoid hard braking and high-speed driving. Stop the vehicle in a safe place and we rec- ommend you to have th
e vehicle checked.
N00568400058
The power steering system operates while the electric motor unit is running. It helps reduce the effort needed to turn the steering wheel. The power steering system has mechanicalsteering capability in ca
se the power assist is
lost. If the power assist is lost for some rea- son, you will still be able to steer your vehi-cle, but you will notice it takes much more effort to steer. If this happens, have your vehi- cle inspected at a certified i-MiEV dealer.
If the warning light illuminates while driving If only the ABS warning light illu- minate If the ABS warning light and brake warning light illuminate at the same time
NOTE
 The warning light may
be illuminated when
the electric motor unit is started while the12V starter battery voltage
is low, but this is
not an ABS malfunction. When the main drive lithium-ion battery is charged, the 12V starte
r battery is charged at
the same time, and the
warning light will go
out. If the warning light does
not go out or illumi-
nates from time to time even after the battery is charged, take your ve
hicle to a certified i-
MiEV dealer and have
the system checked as
soon as possible.  After driving on snow or icy roads, remove any snow and ice whic
h may have been left
around the wheels. On ve
hicles that have an
anti-lock braking system, be careful not todamage the wheel spee
d sensors (A) or the
cables located at each wheel.Front
Electric power steering sys- tem (EPS) Rear
BK0209800US.book 27 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Active stability control (ASC) Features and controls 5-29
5
N00559200089
On slippery surfaces, the traction control function prevents the drive wheels from spin- ning excessively, thus helping the vehicle to start moving from a stopped condition. It alsoprovides sufficient driving force and steering performance as the vehicle turns while press- ing the acceleration pedal.
N00546800049
The skid control function is designed to help the driver maintain control of the vehicle on slippery roads or during rapid steeringmaneuvers. It works by controlling the elec- tric motor unit output and the brake on each wheel.
N00559401277
The ASC is automatically activated when theelectric motor switch is turned to the “ON” position. You can deacti
vate the system by
pressing down the ASC OFF switch for 3 sec-onds or longer. When the ASC is deacti
vated, the indica-
tor will be illuminated. To reactivate the
ASC, momentarily
press the ASC OFF
switch; the indicator is turned off.
NOTE
 An operation noise may be emitted from under the hood in the fo
llowing situations.
The sound is associated
with checking the
operations of the ASC.
At this time, you may
feel a shock from the brake pedal if you depress it. These do not indicate a malfunc-tion. • When the electric motor switch is set to the “ON” position. • When the vehicle is driven for a while after the electric motor unit is turned on.
 When the ASC is acti
vated, you may feel a
vibration in the vehicle body or hear a whin- ing sound from under the hood. This indicates that the system is operatingnormally. It does not i
ndicate a malfunction.
 When the anti-lock braking system warning light is illuminated, the ASC is not active.
Traction control function
CAUTION When driving a vehicle on a snowy or icy road, be sure to install snow tires and drivethe vehicle at moderate speeds.
Skid control function
NOTE
 The skid control func
tion operates at speeds
of about 9 mph (15 km/h) or higher.
ASC OFF switch
CAUTION For safety reasons, the ASC OFF switch should be operated when your vehicle isstopped.  Be sure to keep the ASC on while driving in normal circumstances.NOTE
 Using the ASC OFF swit
ch turns off both the
skid control function a
nd the traction control
function.  When moving out of mud, sand or fresh snow, pressing the ac
celerator pedal may not
allow the electric motor speed to increase. Insuch situations, temporarily deactivate the ASC, using the ASC OFF switch.
BK0209800US.book 29 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Instrument cluster
Features and controls 5-35
5
N00572101037
The power consumption of the electric motor, the air conditioning, and power generation by the regenerative brake are indicated. When the ready indicator comes on, the redneedle will move to th
e neutral point (A) and
then move to the right or left according to the amount of power consumption or power gen-eration. [When the red needle moves to the right of the neutral point] This indicates that the electric motor unitand/or the air conditioning are consuming electric energy from the main drive lithium- ion battery.The more the needle moves to the right, the more electrical energy
is being consumed.
[When the red needle moves to the left of the neutral point]This indicates that electric energy is being generated by the regenerative brake and charged to the main dr
ive lithium-ion battery.
The more the needle moves to the left, the more electric energy is being generated.
N00519501449
Odometer, trip odometer
, dash lights bright-
ness indicator, serv
ice reminder, cruising
range indicator, and outside temperature are displayed.
N00572201025
The display is changed every time the reset button (A) is briefly pressed.
NOTE
 Even if speedometer
’s display unit is
changed, the display units for the odometer,trip odometer, and service reminder do notchange.
Energy usage indicator
NOTE
 When the main drive lithium-ion battery is at or near full charge, or
the main drive lithium-
ion battery temperature is too high or too low, the needle in the energy usage indicatormay not move to the left of the neutral point, since the main drive lithium-ion battery can- not receive charge.
Odometer/Trip
odometer/Dash
lights brightness indicator/Ser-vice reminder/Cruising range indicator/Outside temperature display To change the display
BK0209800US.book 35 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Indicator and warning light package
Features and controls 5-41
5
N00519801862
Indicator and warning light package 1- Low energy warning indicator
 P.5-40
2- Selector lever
position indicator
 P.5-21
3- Acoustic Vehicle Alerting System
( AVA S ) i n d i c a t o r
 P.5-23
4- High-beam indicator
 P.5-42
5- Turn-signal indicators/Hazard warning
lights
 P.5-42
6- Position indicator
 P.5-42
7- Front fog light indicator
 P.5-42
8- Service reminder
 P. 5 - 3 6
9- Outside air temperature warning indi-
cator
 P. 5 - 3 9
10- Regenerative brake system indicator
 P.5-42
11- Ready indicator
 P.5-42
12- Tire pressure moni
toring system warn-
ing light
 P.5-31
13- 12V starter battery charging system
warning light
 P.5-43
14- Electric power steering system warning
light
 P.5-28
15- Electric motor unit warning light
 P.5-43
16- Brake warning light
 P. 5 - 4 2
17- Anti-lock braking system warning light
 P.5-26
18- Power down warning light
 P.5-43
19- Active stability control (ASC) indicator
 P.5-30
20- Active stability control (ASC) OFF
indicator
 P. 5 - 3 0
21- Charging indicator
 P.5-42
22- Theft-alarm indicator
 P.5-12
23- Door-ajar warning light
 P.5-43
24- Driver’s seat belt reminder/warning
light
 P. 4 - 1 0
25- Supplemental Restra
int System (SRS)
warning light
 P.4-13
BK0209800US.book 41 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Indicators 5-42 Features and controls
5
N00519900127 N00520000232
The arrows will flash in time with the corre- sponding exterior turn signals when the turnsignal lever is used. Both arrows will flash
when the hazard warn-
ing flasher swit
ch is pressed.
N00520100086
A blue light comes on when the headlights are on high beam.
N00520201244
This indicator comes on while the front foglights are on.
N00551300039
This indicator turns on while the position lights are on.
N00573200012
This indicator comes on when the electricmotor switch is turned to “START” and driv- ing becomes possible.
N00573300013
This indicator flashes when the regular charg-ing cable or quick charging cable is con- nected. After that, the light switches to being illumi-nated when charging starts and goes out when charging is completed.
N00573400014
The indicator comes on when the regenera- tive brake performance may be weakened. Inthis case, drive the vehicle at a lower speed.
N00520300147 N00520400513
This light comes on when the electric motor switch is turned to the “ON” position, and goes off after a few seconds when the parkingbrake is released. Befo
re driving your vehi-
cle, release the parki
ng brake and make cer-
tain that the brake warning light has gone off. If the light stays on when the parking brake is fully released, the service brake system is notworking properly or the brake fluid level is low.
Indicators Turn signal indicators/Hazard warning lights
NOTE
 If the indicator flashes faster than usual or if the indicator stays on wi
thout flashing, check
for a malfunctioning turn signal light bulb orturn signal connection.
High beam indicator Front fog light indicator
Position indicator Ready indicator Charging indicator Regenerative brake system indicator
Warning lights Brake warning light
WA R N I N G If any of the follow
ing conditions occur,
the brake effort
may significantly
increase. Stop the vehicle in a safe loca- tion, avoiding where possible any sudden brake application, a
nd contact a certified
i-MiEV dealer.• The brake warning light does not comeon when the electric motor switch is turned to the “ON” position.• The brake warning li
ght does not illumi-
nate while the parking brake is applied and the electric motor switch is in the“ON” position. • The brake warning
light stays on when
the parking brake is not applied.
BK0209800US.book 42 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Warning lights
Features and controls 5-43
5
N00573500028
This light will illuminate when there is a problem with the charging system for the 12V starter battery.Normally, when the electric motor switch is turned to the “ON” position, this light will illuminate. Then, when the electric motor unitis started and the ready indicator illuminates, the light will go out.
N00520900316
This light comes on when any door or liftgate is open or not completely closed.When the vehicle is moving at more than 5 mph (8 km/h) and any door or liftgate is open or ajar, a tone will sound 16 times and thewarning light will fl
ash 16 times to inform
the driver that a door or liftgate is not prop- erly shut.
N00573600029
This warning light will illuminate when thereis a problem with a high voltage component.Refer to “Service prec
autions” on page 9-2.
N00573700020
NOTE
When the brake warning light illuminates, the warning buzzer may also sound.  When the brake pedal has been repeatedly depressed over a short period of time, the brake warning light may come on and thebrake warning buzzer may sound. The ser- vice brake system is working normally, if the warning light goes out and the buzzer stopssounding in a few seconds.
12V starter battery charging system warning light
CAUTION If the warning light stays on after the ready indicator illuminates,
there may be a prob-
lem with the charging system for the 12Vstarter battery.• Immediately park your
vehicle in a safe
place and contact a cert
ified i-MiEV dealer.
• Do not charge the
12V starter battery.
Door-ajar warning light and buzzer
CAUTION Before driving, make sure that the door-ajar warning light is off. NOTE
 The flashing of the warning light and the buzzer can be disabled. For further details, plea
se contact a certified
i-MiEV dealer.  When the driver’s door is open, the door-ajar warning buzzer does not
sound because the
electric motor remi
nder sounds instead.
Electric motor unit warning light
CAUTION If this light illuminates while driving, imme- diately park your vehicle in a safe place andcontact a certified i-MiEV dealer.
Power down warning light
If this warning light illumi- nates, the power provided bythe electric motor will be reduced and the vehicle will be only able to move at lowspeeds. This warning light will illu- minate; When the energy level in the main drive lithium-ion battery is near empty.
BK0209800US.book 43 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Combination headlights and dimmer switch 5-44 Features and controls
5
If the warning light illuminates when the out- side air temperature is very low, move thevehicle to a warmer location. If the warning light illuminates after the vehi- cle has been driven continuously uphill orwhen the outside air te
mperature is very high,
stop the vehicle in a safe place so the electric motor unit and/or the main drive lithium-ionbattery can cool down. When they have cooled down, the warni
ng light will go off. If
the warning light does not
turn off, contact a
certified i-MiEV dealer.
N00522501805
Rotate the switch to operate the lights.
The combinations of
switch operations and
illuminated lights differ in accordance withthe following conditions. [When the ready indicato
r is illuminated, and
the parking brake is released] The daytime running lights will be illumi- nated:
 When temperature of the electric motor unit or the main drive lithium-ionbattery is too high or too low.  When voltage of the main drive lithium-ion battery becomes low.
If the energy level gaugeshows 0 bar, the main drive lithium-ion battery is near empty and must be charged as soon as possible. Refer to “Charging” on page 3-11.
NOTE
 When the power down warning light illumi- nates, avoid rapid st
arts and aggressive
acceleration.
 Illumination of the
power down warning
light does not indica
te a malfunction.
 If the power down warn
ing light illuminates
while the air conditioning is used, the cool- ing or heating may stop operating and onlythe fan will operate.
Combination headlights and dimmer switch Headlights
NOTE
 Do not leave the head
lights and ot
her lights
on for a long period of time while the readyindicator is not illum
inated. A run down 12V
starter battery
could result.
 When it rains, or wh
en the vehicle has been
washed, the inside of the lens sometimes becomes foggy. This is the same as whenwindow glass mists up
on a humid day, and
does not indicate a problem. When the light is switched on, the heat
will dry out the fog.
However, if water collects inside the light,have it checked by a certified i-MiEV dealer.NOTE
OFF
The daytime running lights illumi- nated
AUTO
The daytime running lights illumi- nated Headlights and other lights turn on and off automatically in accor-dance with outside light level.
BK0209800US.book 44 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Combination headlights and dimmer switch
Features and controls 5-45
5
[When the ready indicato
r is not illuminated,
or when the ready indicator is illuminated but the parking brake is not released] The electric motor unit starts when the lights are off.
N00532600554
 If the key is turned to “LOCK” or “ACC” position or removed from the electric motor switch and the driver’s door is opened with the comb
ination headlights
and dimmer switch in the “ ” or “ ” position, the lights automatically turn off.
• If the driver’s door is opened after the key is removed from the electric motorswitch, a buzzer will sound to remind you to turn off the lights. • If the driver’s door is opened with thekey in the electric motor switch, a buzzer will sound intermitte
ntly to remind you
to remove the key.
 If the key is turned to “LOCK” or “ACC” position with the driver’s door closed and the combination headlights and dimmer switch in the “ ” or “ ” position, the lights will stay on for about 3 minutes and then turn off automatically.
If the combination
headlights and dimmer
switch is turned to the “ ” or “ ” posi- tion again after the electric motor switch is turned to “LOCK” or “ACC” position, the auto-cutout function described above will not work. The lights (the park
ing lights, tail lights
The daytime running lights illumi- nated Parking, tail, front
and rear side-
marker lights, license plate and instrument panel lights on Headlights and other lights on
NOTE
 Once the daytime running light come on, they do not go out until the electric motorswitch is turned to the “LOCK” or “ACC” position.OFF All lights off AUTO
Headlights and other lights turn on and off automatically in accor-dance with outsi
de light level.
Parking, tail, front
and rear side-
marker lights, license plate and instrument panel lights on Headlights and other lights on
NOTE
 The sensitivity of the automatic on/off con- trol can be adjusted.For further information, please contact a cer-tified i-MiEV dealer.  Do not place anything on the sensor (A), and do not clean with a gla
ss cleaner. Clean only
with clear water.  If the lights do not turn on or off with the switch in the “AUTO”
position, manually
operate the switch. Have the system checked by a certified i-MiEV dealer.
Light auto-cutout function (headlights and other lights)
NOTE
 The light auto-cutout f
unction can be deacti-
vated. See a certified i-MiEV dealer for details.
When you want to keep the lights on:
BK0209800US.book 45 ページ ２０１４年１月１４日　火曜日　午前９時２６分