2014 MINI Clubman radio

Snap-in adapter
General information More information on compatible snap-in
adapters that support the functions of the mo‐
bile phone is available at the service center.
Notes At high temperatures, the charging function of
the mobile phone may be limited and functions
may not be executed.
When using the mobile phone via the vehicle,
note the operating instructions of the mobile
phone.
Installation position In the center armrest.
Inserting/removing the snap-in adapter1.Press button 1 and remove the cover.2.Insert the snap-in adapter at the front, ar‐
row 1, and press down, arrow 2, until it en‐
gages.3.To remove the snap-in adapter: press but‐
ton 1.
Inserting the mobile phone
1.Depending on the mobile phone, remove
the protective cap from the antenna con‐
nector and from the USB connection of the
mobile phone.2.With the buttons facing up, slide the mobile
phone up toward the electrical contacts
and press it down until it engages.
The battery is charged beginning with the radio
ready state of the vehicle.
Seite 133TelephoneCommunication133
Online Edition for Part no. 01 40 2 911 429 - VI/13

Charging the battery
Note Do not connect the charger to the socket
Do not connect the battery charger to the
socket installed in the vehicle at the factory as this could damage the battery. ◀
Only charge the battery in the vehicle when the
engine is switched off. Connections, refer to
page 175.
General information
Ensure that the battery is sufficiently charged to
achieve the full battery life.
It may be necessary to charge the battery in
the following cases:▷When the vehicle is frequently used to
travel short distances.▷When the vehicle has not been driven for
more than one month.
Power failure
After a temporary power failure, some equip‐
ment will be restricted in its use and will need
to be reinitialized. In addition, certain individual
settings will be lost and must be updated:
▷Time and date: the values must be up‐
dated, refer to page 58.▷Radio: the stations need to be stored again,
refer to page 116.▷Glass sunroof, electrical: it may only be pos‐
sible to tilt the roof. The system needs to be
initialized. Contact the service center.
Disposing of old batteries
Have used batteries disposed of by the
service center after they are replaced or
take them to a recycling center.
Maintain the battery in an upright position for
transport and storage. Secure the battery so
that it does not tip over during transport.
Fuses
Replacing fuses
Never attempt to repair a blown fuse and
do not replace a defective fuse with a substi‐
tute of another color or amperage rating; this
could lead to a circuit overload, ultimately re‐
sulting in a fire in the vehicle. ◀
Fuses should be replaced by the service center.
Information on the fuses can be found on the
inside of the covers.
In the engine compartment
Opening the cover
Press the snap lock.
In interior
On the right side of the footwell.
Opening the cover
Push out at the recess.
Seite 173Replacing componentsMobility173
Online Edition for Part no. 01 40 2 911 429 - VI/13

MINI Clubman
The first aid kit is located in the left side trim on
the cargo area floor or under the flat loading
floor.
Roadside Assistance
Service availability Roadside Assistance can be reached around the
clock in many countries. You can obtain assis‐
tance there in the event of a vehicle break‐
down.
Roadside Assistance A phone number for Roadside Assistance can
be displayed, refer to page 132, via the radio.
Jump-starting NotesIf the battery is discharged, the engine can be
started using the battery of another vehicle and
two jumper cables. In the same way, you can
help jump-start another vehicle. Only use
jumper cables with fully insulated clamp han‐
dles.
To prevent personal injury or damage to both
vehicles, adhere strictly to the following proce‐
dure.
Do not touch live parts
To avoid the risk of potentially fatal injury,
always avoid all contact with electrical compo‐
nents while the engine is running. ◀
Preparation1.Check whether the battery of the other ve‐
hicle has a voltage of 12 volts and approxi‐
mately the same capacitance in Ah. This in‐
formation can be found on the battery.2.Switch off the engine of the assisting vehi‐
cle.3.Switch off any electronic systems/power
consumers in both vehicles.
Bodywork contact between vehicles
There must not be any contact between
the bodies of the two vehicles, otherwise there
is a danger of shorting. ◀
Seite 175Breakdown assistanceMobility175
Online Edition for Part no. 01 40 2 911 429 - VI/13

Chrome surfacesCarefully clean components such as the radia‐
tor grille or door handles with an ample supply
of water, possibly with shampoo added, partic‐
ularly when they have been exposed to road
salt. For additional treatment, use a chrome
polish.
Light-alloy wheels
When cleaning the wheels on the vehicle, only
use a neutral wheel rim cleaner with a pH value
of 5 to 9.
Do not use abrasive cleaners or a steam jet hot‐
ter than 140 ℉/60 ℃; otherwise, damage may
result. Adhere to the manufacturer instructions.
Aggressive, acidic, or alkaline cleaners may de‐
stroy the protective coating of neighboring
components such as the brake disc.
Exterior sensors The sensors on the outside of the vehicle, such
as for Park Distance Control, must be kept clean
and free of ice to ensure that they remain fully
functional.
Decorative trim Clean decorative trims and fine wood compo‐
nents with a moist cloth only. Then dry with a
soft cloth.
Safety belts Dirty belt straps impede the reeling action and
thus have a negative impact on safety.
No chemical cleaning
Do not clean chemically; this can destroy
the webbing. ◀
Carpets/floor mats No objects in the area around the pedals
Keep floor mats, carpets, and any other
objects out of the area of motion of the pedals;
otherwise, the function of the pedals could be
impeded while drivingDo not place additional floor mats over existing
mats or other objects.
Only use floor mats that have been approved
for the vehicle and can be properly fixed in
place.
Ensure that the floor mats are securely fastened
again when they are returned after being re‐
moved, such as for cleaning. ◀
Floor mats can be removed for cleaning.
If they are very dirty, clean with a microfiber
cloth and water or an interior cleaner. To pre‐
vent matting of the carpet, rub back and forth
in the direction of travel only.
Displays
To clean the displays, such as the radio or dis‐
play elements, use an antistatic microfiber
cloth.
Cleaning displays
Do not use chemical or household cleans‐
ers.
Keep all fluids and moisture away from the
unit.
Otherwise, they could affect or damage surfa‐
ces or electrical components.
Avoid pressing too hard when cleaning and do
not use abrasive materials; otherwise, damage
can result. ◀
CD/DVD drives No cleaning CD
Do not use cleaning CDs; otherwise, parts
of the drive may become damaged. ◀
Long-term vehicle storage
Your service center can advise you on what to
consider when storing the vehicle for longer
than three months.Seite 182MobilityCare182
Online Edition for Part no. 01 40 2 911 429 - VI/13

12CauseHow to respondThe Flat Tire Monitor was not initialized.Initialize the Flat Tire Monitor, re‐
fer to page 69.Light up in yellow:Flat Tire Monitor failed. Punctures are not in‐
dicated.Have the system checked.In vehicles with the Tire Pressure MonitorLight up in yellow and red:There is a flat tire or substantial loss of tire
pressure.Carefully bring the car to a stop.
Additional information, refer to
page 72.In vehicles with the Tire Pressure MonitorLight up in yellow:Tire Pressure Monitor not initialized.Check the inflation pressure and
reset the system, refer to
page 72.The small lamp flashes yellow and then stays
on, the large lamp lights up in yellow:Tire Pressure Monitor failed. Punctures are
not indicated.Have the system checked.A wheel without TPM electronics is mounted.Have the system checked.TPM is temporarily malfunctioning due to
other systems or devices using the same
radio frequency.In vehicles with the Tire Pressure MonitorThe small lamp flashes yellow and then stays
on, the large lamp lights up in yellow:Tire Pressure Monitor failed. Punctures are
not indicated.Have the system checked.A wheel without TPM electronics is mounted.Have the system checked.Lights up in red:Seite 190MobilityIndicator/warning lamps190
Online Edition for Part no. 01 40 2 911 429 - VI/13

Hood, opening 156
Hood, unlocking 156
Horn 12
Hydraulic brake assistant 76
I
Ice warning, refer to External temperature warning 54
Icy roads, refer to External temperature warning 54
Identification marks, run-flat tires 151
Identification marks, tires 147
Ignition 44
Ignition key position 1, refer to Radio ready state 44
Ignition key position 2, refer to Ignition on 44
Ignition key, refer to Remote control with integrated
key 20
Ignition lock 44
Ignition, switched off 45
Ignition, switched on 44
Indicator and warning lamps 15
Indicator and warning lamps– Tire Pressure Monitor
TPM 73
Indicator and warning lamps,
overview 183
Individual air distribution 83
Inflation pressure monitor, re‐ fer to Flat Tire Monitor 69
Inflation pressure monitor, re‐ fer to Tire Pressure Monitor
TPM 72
Inflation pressure, refer to Tire inflation pressure 142
Initializing
– Compass, refer to Calibrat‐
ing 90– Glass sunroof, electrical 31
Initializing, Flat Tire Monitor
FTM 70
Instrument cluster, refer to
Displays 14
Instrument lighting 65
Instruments, refer to Cock‐ pit 12
Integrated key 20
Interior equipment 87
Interior lamps 65
Interior lamps– Remote control 24
Interior mirror 38
Interior rearview mirror, com‐ pass 89
Interior temperature, setting
– Air conditioner 82– Automatic climate con‐
trol 84
Internet page 6
J Jump-starting 175
K
Keyless Go, refer to Comfort Access 28
Keyless opening and closing, refer to Comfort Access 28
Key Memory, refer to Personal Profile 20
Key, refer to Remote control with integrated key 20
Kickdown
– Automatic transmission with
Steptronic 52
Knocking control 140
L Lamp and bulb replacement, bulb replacement 164
Lamp, replacing, refer to Lamp and bulb replace‐
ment 164
Lamps 62
Lamps, automatic headlamp
control 62
Lamps, parking lamps/low beams 62
Lap-and-shoulder belt, refer to Safety belts 36
LATCH child restraint fixing system 41
Leather, care 181
Leather care 181
LEDs, light-emitting di‐ odes 164
License plate lamp, bulb re‐ placement 167
Light-alloy wheels, care 182
Light-emitting diodes, LEDs 164
Lighter– Socket 91
Lighting
– Instruments 65
Lighting, lamp and bulb re‐
placement 164
Lighting, vehicle, refer to Lamps 62
Light switch 62
Lock buttons on doors, refer to Locking 25
Locking
– From the inside 25– From the outside 23– Setting the confirmation sig‐
nal 23– Without remote control, re‐
fer to Comfort Access 28
Locking, vehicle
– From the inside 25– From the outside 22
Longlife oils, alternative oil
types 158
Longlife oils, refer to Ap‐ proved engine oils 158
Low beams 62
Low beams
– Automatic 62
Low beams, automatic 62
Seite 204ReferenceEverything from A to Z204
Online Edition for Part no. 01 40 2 911 429 - VI/13

Prescribed engine oils, refer toApproved engine oils 158
Pressure monitoring of tires, refer to Tire Pressure Monitor
TPM 72
Pressure, tires 142
Pressure warning, tires 69
Profile depth, refer to Mini‐ mum tread depth 148
Profile, tires 148
Protective function, refer to
Pinch protection– Windows 32
R
Radio MINI Boost CD 112
Radio-operated key, refer to Remote control with
integrated key 20
Radio ready state 44
Radio ready state, switched off 45
Radio ready state, switched
on 44
Radio setting, refer to Radio ready state 44
Rain sensor 48
Range 56
Rear door, refer to Club‐ door 26
Rear doors, refer to Split door 27
Rear fog lamp 65
Rear fog lamp, bulb replace‐ ment 167
Rear lamps, refer to Tail lamps 167
Rear swing doors, refer to Split door 27
Rearview mirror, refer to Mir‐ rors 38
Rear window defroster 83, 86
Rear window, washing 50
Rear window wiper 50
Recirculated air mode 83, 85
Recommended tire
brands 150
Releasing, refer to Unlock‐ ing 28
Remaining range for service, refer to Service require‐
ments 59
Remaining range, refer to Range 56
Remote control– Battery replacement 30– Comfort Access 28– Malfunctions 24, 29– Split door 24
Remote control, removing
from the ignition lock 44
Remote control, service data 160
Remote control, universal 87
Replacement remote con‐ trol 20
Replacing wheels/tires 149
Reporting safety defects 9
Reserve warning, refer to Fuel gauge 55
Reservoir for washer fluid, re‐ fer to Washer fluid reser‐
voir 50
Restraining systems
– Refer to Safety belts 36
Restraint systems for chil‐
dren 40
Retreaded tires 150
Reverse gear, manual trans‐ mission 51
Roadside Assistance 175
Roadside parking lamp, bulb replacement 166
Roadside parking lamps 63
RON gasoline quality 140
RON, refer to Fuel quality 140
RPM, refer to Engine data 196
Rubber seals, care 181
Run-flat tires 151
Run-flat tires
– Flat tire 70Run-flat tires, tire inflation
pressure 142
Running lights, refer to Park‐ ing lamps/low beams 62
S Safe braking 102
Safety 6
Safety belts 36
Safety belts– Damage 37
Safety belts, care 182
Safety belts, indicator/warning lamp 37
Safety belts, reminder 37
Safety systems
– Safety belts 36
Safety systems, airbags 67
Saving fuel 108
Seat adjustment
– Manual 34
Seat belts
– Refer to Safety belts 36
Seat heating 36
Seats
– Adjusting 34– Heating 36– Sitting safely 34
Selector lever, automatic
transmission with Step‐
tronic 52
Selector lever lock, overrid‐ ing 53
Selector lever lock, refer to Changing selector lever posi‐
tions, Shiftlock 52
Selector lever positions, auto‐ matic transmission with
Steptronic 52
Service and warranty 7
Service data in the remote control 160
Service interval display, refer to Condition Based Service
CBS 160
Seite 206ReferenceEverything from A to Z206
Online Edition for Part no. 01 40 2 911 429 - VI/13