2014 MERCEDES-BENZ CLS hood release

Dashboard
FunctionPage
Steeringwheelpaddle
shifters160
Cruisecontrollever176
$Instrumentcluster31
!Horn
DIRECTSELECTlever155
%PARKTRONIC warning
display193
Overhead controlpanel37
Climatecontrolsystems130
Ignition lock147
Start/Stopbutton147
FunctionPage
Adjuststhesteeringwheel106
Steeringwheelheating107
Combination switch119
Parking brake169
Diagnosticsconnection25
Opens thehood306
Releases theparking brake169
Light switch116
Night ViewAssistPlus204
30Dashboard
At ag lance

thathas collectedonthewindshield can
scratch theglass if wipingtakes placewhen
thewindshield is dry.
If it is necessary to switch on thewindshield
wipersindry weather conditions, always
use washerfluid when operating the
windshield wipers.
!If the windshield wipers leave smearson
the windshield after the vehicle has been
washed in an automatic car wash, wax or
other residues may be the reason for this.
Clean the windshield using washer fluid
after washingthe vehicle in an automatic
car wash.
!Intermittentwiping with rain sensor: due
to optical influences and the windshield
becomingdirtyindry weatherconditions,
the windshield wipers may be activated
inadvertently. This could then damage the
windshield wiper blades or scratchthe
windshield.
For this reason, you should always switch
off the windshield wipers in dry weather.
Combination switch

Windshield wiper off
Intermittent wipe, low (rain sensor
set to low sensitivity)
Intermittent wipe, high (rain sensor
set to high sensitivity)
Continuous wipe, slow
Continuous wipe, fast
%Single wipe/
To wipe the
windshield using washer fluid
XSwitch on the ignition.
XTurn the combination switch to the
corresponding position.
In theorposition, the appropriate
wiping frequency is set automatically
according to the intensity of the rain. In
theposition, the rain sensor is more
sensitive than in theposition, causing
the windshield wipers to wipe more
frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic
conditions. Replace the wiper blades twice a
year, ideallyinspring and fall.
Replacing the wiper blades
Important safety notes
GWARNING
If the windshield wipers begin to move while
you are changing the wiper blades, you could
be trapped by the wiper arm. There isarisk
of injury.
Always switch off the windshield wipers and
ignition before changing the wiper blades.
!To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
!Never open the hood ifawindshield wiper
arm has been folded away from the
windshield.
Never foldawindshield wiper arm without
awiper blade back ontothe windshield.
Hold the windshield wiper arm firmly when
you change the wiper blade. If you release
the windshield wiper arm withoutawiper
blade and it falls ontothe windshield, the
windshield may be damaged by the force of
the impact.
Mercedes-Benz recommends that you have
the wiper blades changed ataqualified
specialist workshop.
126Windshieldwipers
Light sa nd windshield wipers

Activating DISTRONIC PLUS
Activation conditions
In order to activateDISTRONICPLUS, the
followingconditionsmustbefulfilled:
Rthe enginemust be started. It may take up
to two minutes after pulling away before
DISTRONIC PLUS is operational.
Rthe parkingbrake must be released.
RESP®must be active, but not intervening.
RActive ParkingAssist must not be
activated.
Rthe transmission must be in positionD.
Rthe hood must be closed.
Rthe driver's door must be closed when you
shift fromPtoDor your seat belt must be
fastened.
Rthe front-passenger door and rear doors
must be closed.
Rthe vehicle must not skid.
Activating
XBriefly pull the cruise control lever towards
youor press it upor down$.
DISTRONIC PLUS is selected.
XPress the cruise control lever repeatedly
upor down$until the desired speed
is set.
XRemove your foot from the accelerator
pedal.
Your vehicle adapts its speed to that of the
vehicle in front, but only up to the desired
stored speed.
When driving at speeds below 20 mph
(30 km/h),you can only activate DISTRONIC
PLUS if the vehicle in front has been detected
and is shown in the multifunction display.If
the vehicleinfront is no longerdetected and
displayed, DISTRONIC PLUS switches off and
atonesounds.
iIf you do not fully release the accelerator
pedal, theDISTRONIC PLUS Override
message appears in the multifunction
display. The set distancetoaslower-
movingvehicle in frontwill then not be
maintained. You will be driving at the speed
you determine by the position of the
accelerator pedal.
Activating when driving towardsa
stationary vehicle
XBriefly pull the cruise control lever towards
you!or press it upor down.
DISTRONIC PLUS is selected.
XPress the cruise control lever repeatedly
upor downuntil the desired speed
is set.
If the vehicle in frontofyou is stationary, you
can only activate DISTRONIC PLUS once your
vehicle is stationary as well.
iDISTRONIC PLUS can only be activated at
under 20 mph (30 km/h) ifavehicle in front
has been detected. Therefore, the
DISTRONIC PLUS distancedisplay in the
instrument cluster should be activated
(Ypage 227).
iYou can use the cruise control lever to set
the stored speed and the control on the
cruise control lever to set the specified
minimum distance(Ypage 183).
Activating at the current speed/last
stored speed
GWARNING
If you call up the stored speed and it differs
from the currentspeed, the vehicle
accelerates or decelerates. If you do not know
the stored speed, the vehicle could accelerate
180Driving systems
Driving and parking

Important safety notes
GWARNING
When leaving thevehicle, it can still rollaway
despitebeingbraked by theHOLD function if:
Rthere isamalfunction in the system or in
the voltage supply.
Rthe HOLD function has been deactivated by
pressing the accelerator pedal or the brake
pedal,e.g. byavehicle occupant.
Rthe electrical system in the engine
compartment,the battery or the fuses have
been tampered with.
Rthe battery is disconnected
There isarisk of an accident.
If you wish to exit the vehicle, always turn off
the HOLD function and secure the vehicle
against rolling away.
!If DISTRONIC PLUS or the HOLD function
is activated, the vehicle brakes
automaticallyincertain situations. To
prevent damage to the vehicle, deactivate
DISTRONIC PLUS and the HOLD function in
the following or other similarsituations:
Rwhen towingthe vehicle
Rin the car wash
Activation conditions
You can activatethe HOLDfunction if:
Rthe vehicle is stationary
Rthe engine is running or if it has been
automatically switched off by the ECO
start/stop function
Rthe driver's door is closed or your seat belt
is fastened
Rthe parking brakeisreleased
Rthe hood is closed
Rthe transmission is in positionD,RorN
RDISTRONIC PLUS is deactivated
Activating theHOLD function
XMake sure that the activation conditions
are met.
XDepress the brakepedal.
XQuickly depressthe brakepedal further
untilappears in the multifunction
display.
The HOLDfunction is activated. You can
release the brakepedal.
iIf depressing the brakepedal the first
timedoes not activatethe HOLDfunction,
wait briefly and thentry again.
Deactivatingthe HOLD function
The HOLD function is deactivated
automatically if:
Ryou accelerate and the transmission is in
positionDorR.
Ryou shift the transmission to positionP.
Ryou depress the brake pedalagain with a
certain amount of pressure until
disappears from the multifunction display.
Ryou activate DISTRONIC PLUS.
When the HOLD function is activated,the
transmission is shifted automatically to
positionPif:
Rthe driver's door is open and the driver's
seat beltisunfastened.
Rthe engine is switched off, unless it is
automaticallyswitched off by the ECO
start/stop function.
Rthe hood is opened.
Rasystem malfunction occurs.
Rthe power supplyisnot sufficient.
Driving systems187
Driving and parking
Z

XPress and hold one of buttonsto!on
the integrated garage door opener.
Afterashort time, indicator lamplights
up yellow.
XRelease the button.
Indicator lampflashes yellow.
XPress button%of garage door remote
controlfor two seconds, then release it
for two seconds.
XPress button%again for two seconds.
XRepeat this sequence on button%of
remotecontroluntil indicator lamp
lights up green.
If indicator lampturnsred, repeat the
process.
XContinue with the other programming
steps (see above).
Problems when programming
If you are experiencing problems
programmingthe integrated garage door
opener on the rear-view mirror, take noteof
the following instructions:
RCheck the transmitter frequencyofgarage
door drive remotecontrol.This can
usually be found on the back of the remote
control.
The integrated garage door opener is
compatible with devices that have units
which operate in the frequency range of
280to433MHz.
RReplace the batteries in garage door
remote control.This increases the
likelihood that garage door remote control
will transmitastrongand precisesignal
to the integrated garage door openerinthe
rear-view mirror.
RWhen programming, hold remote control
at varying distances and angles from the
button that you are programming. Try
various angles atadistance between 2and
12 inches (5to 30 cm) or at the same angle
but at varying distances.
RIf another remote control for the same
garage door drive is available, repeat the
same programming steps with this remote
control. Before performing these steps,
make sure that new batteries have been
installed in garage door drive remote
control.
RNote that some remote controls only
transmit foralimited amount of time (the
indicator lamp on the remote control goes
out). Press button%on remote control
again before transmission ends.
RAlign the antennacable of the garage door
opener unit. This can improve signal
reception/transmission.
Opening/closing the garage door
After it has been programmed, the integrated
garage door opener performs the function of
the garage door system remote control.
Please also read the operating instructions
for the garage door system.
XTurn the SmartKey to position2in the
ignition lock.
XPress button,$or!which you have
programmed to operate the garage door.
Garage door system withafixed code:
indicator lamplights up green.
Garage door system witharolling code:
indicator lampflashes green.
iThe transmitter will transmitasignal as
long as the button is pressed. The
transmission is halted afteramaximum of
ten seconds and indicator lamplights
up yellow. Press button,$or!again
if necessary.
Clearing the memory
XTurn the SmartKey to position2in the
ignition lock.
XPress buttonsand!.
The indicator lamp lights up yellow.
XPress and hold buttonsand!until the
indicator lamp turns green.
Features301
Stowage and features
Z

!Make sure that the windshieldwipers are
not folded away fromthe windshield. You
could otherwise damage the windshield
wipers or the hood.
XMake sure that the windshield wipers are
turned off.
XPull release leveron the hood.
The hood is released.
XReach into the gap, pull hood catch
handleup and lift the hood.
If you lift the hood by approximately
15 inches(40cm),the hood is opened and
held open automatically by the gas-filled
strut.
Closing thehood
XLower the hood and let it fall fromaheight
of approximately8inches(20 cm).
XCheck that the hood has engaged properly.
If the hood can be raised slightly,itisnot
properly engaged. Open it again and close
it withalittle more force.
Engine oil
General notes
Depending on the driving style, the vehicle
consumesupto0.9 US qt (0.8 liters) of oil
overadistanceof600 miles(1,000 km). The
oil consumption may be higher than this when
the vehicle is new or if you frequently drive at
high enginespeeds.
Depending on the engine, the oil dipstickmay
be inadifferent location.
When checking theoil level:
Rpark thevehicle onalevelsurface.
Rtheengineshould be switched off for
approximately fiveminutesiftheengineis
at normal operatingtemperature.
Rif theengineisnotat normal operating
temperature, e.g.ifthe engine was only
started briefly, wait about 30 minutes
before carrying out the measurement.
Checking the oil level using the oil
dipstick
XPull oil dipstickout of the dipstick guide
tube.
XWipe off oil dipstick.
XSlowly slide oil dipstickinto the guide
tube to the stop, and take it out again.
If the level is between MIN mark$and
MAX mark,the oil level is correct.
XIf the oil level has dropped to MIN mark
$or below, add 1.1 US qt (1.0 liter) of
engine oil.
Engine compartment307
Maintenance and care
Z

The fuses are located in various fuse boxes:
RFuse box in the engine compartment on the
left-hand side of the vehicle, when viewed
in the direction of travel
Rfuse box in the trunk on the right-hand side,
when viewed in the direction of travel
the fuse allocation chart is located in the
vehicle tool kit in the stowage compartment
under the trunk floor (Ypage 320).
Fuse box in the engine compartment
GWARNING
When the hood is open and the windshield
wipers are set in motion,you can be injured
by the wiper linkage. There isarisk of injury.
Always switch off the windshield wipers and
the ignition before opening the hood.
!Make sure that no moisture can enter the
fuse box when the cover is open.
!When closing the cover, make sure that it
is lying correctly on the fuse box. Moisture
seeping in or dirt could otherwise impair
the operation of the fuses.
XMake sure that the windshield wipers are
turned off.
XOpen the hood.
XUseadry cloth to remove any moisture
from the fuse box.
XTo open:remove linesfrom the guides.
XMove linesaside. Route the lines behind
connection$to do this.
XOpen clamp.
XRemove the fuse box cover forwards.
XTo close:check whether the rubber seal is
lying correctly in the cover.
XInsert the cover at the rear of the fuse box
into the retainer.
XFold down cover and close clamps.
XSecure linesin the guides.
XClose the hood.
Fuse box in the trunk
!Make sure that no moisture can enter the
fuse box when the cover is open.
!When closing the cover, make sure that it
is lying correctly on the fuse box. Moisture
seeping in or dirt could otherwise impair
the operation of the fuses.
XOpen the trunk lid.
XTo open:release coverat the top right
and left-hand sides withaflat object.
XOpen coverdownwards in the direction
of the arrow.
332Fuses
Breakdown assistance