2014 MERCEDES-BENZ CLS check engine light

If you do not open the vehicle within
approximately 40 seconds of unlocking:
Rthe vehicle is locked again.
Rthe theft deterrent locking system is
armed again.
XTo lockcentrally:pressthebutton.
The SmartKey centrally locks/unlocks:
Rthedoors
Rthetrunk lid
Rthefuel filler flap
The turnsignals flash oncewhen unlocking
and three times when locking.
You can also set an audible signal to confirm
that the vehicle has been locked. The audible
signal can be activated and deactivated using
the on-board computer (Ypage 232).
When it is dark, the surround lighting also
comes on if it is activated in the on-board
computer (Ypage 231).
KEYLESS-GO
General notes
Bear in mind that the engine can be started
by any of the vehicle occupants if there is a
KEYLESS-GO key in the vehicle.
Locking/unlocking centrally
You can start, lock or unlock the vehicle using
KEYLESS-GO. To do this, you only need carry
the SmartKey with you. You can combine the
functions of KEYLESS-GO with those of a
conventional SmartKey. Unlock the vehicle
by using KEYLESS-GO, for instance, and lock
it using thebutton on the SmartKey.
When locking or unlocking with KEYLESS-GO,
the distance between the SmartKey and the
corresponding door handle must not be
greater than3ft(1m).
KEYLESS-GO checkswhetheravalid
SmartKey is in the vehicle by periodically
establishingaradio connection between the
vehicle and the SmartKey. This happens:
Rwhen the external door handles are
touched
Rwhen startingthe engine
Rwhile the vehicle is in motion
XTo unlock the vehicle:touch the inner
surface of the door handle.
XTo lock the vehicle:touch sensor
surface.
XConvenience closing feature:touch
recessed sensor surfacefor an
extended period.
XTo unlock the trunk lid:pull the handle on
the trunk lid.
Further information on the convenience
closing feature (Ypage 90).
Changing the settings of the locking
system
You can change the settings of the locking
system. This means that only the driver's door
and the fuel filler flap are unlocked when the
vehicle is unlocked. This is useful if you
frequently travel on your own.
XTo change the setting:press and hold
down theandbuttons on the
SmartKey simultaneously for
SmartKey77
Opening and closing
Z

ProblemPossible causes/consequences andSolutions
The engine cannot be
started using the
SmartKey.
The on-board voltage is too low.
XSwitch off non-essential consumers, e.g. seat heating or interior
lighting, and try to start the engine again.
If this does not work:
XCheck the starter battery and charge it if necessary
(Ypage 324).
or
XJump-start the vehicle (Ypage 326).
or
XConsultaqualified specialist workshop.
The engine cannot be
started using KEYLESS-
GO. The SmartKey is in
the vehicle.
Adoor is open. Therefore, the SmartKey cannot be detected as
easily.
XClose the door and try to start the vehicle again.
There is interferencefromapowerful source of radio waves.
XStart your vehicle with the SmartKey in the ignition lock.
Doors
Important safety notes
GWARNING
If children are left unsupervised in the vehicle,
they could:
Ropen the doors, thus endangering other
people or road users.
Rget out and disrupt traffic.
Roperate the vehicle's equipment.
Additionally, children could set the vehicle in
motion if, for example, they:
Rrelease the parking brake.
Rshiftingthe automatic transmission out of
park positionP
RStart the engine.
There isarisk of an accident and injury.
When leaving the vehicle, alwaystake the
SmartKey with you and lock the vehicle. Never
leave children or animals unattended in the
vehicle. Always keep the SmartKey out of
reach of children.
GWARNING
If persons, particularly children are subjected
to prolonged exposure to extreme heat or
cold, there isarisk of injury, possibly even
fatal. Never leave children unattended in the
vehicle.
Unlocking and opening doors from
the inside
You can openadoor from inside the vehicle
even if it has been locked. If the vehicle has
been locked with the SmartKey or with
KEYLESS-GO, openingadoor from the inside
will trigger the anti-theft alarm system.
Switch off the alarm (Ypage 74).
You can only open the rear doors from inside
the vehicle if they are not secured by the
child-proof locks (Ypage 65).
82Doors
Opening and closing

Useful information
iThis Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please notethat your vehicle may
not be equipped with all features
described. This also applies to safety-
related systemsand functions.
iRead the information on qualified
specialist workshops: (Ypage 26).
Correct driver's seat position
GWARNING
You could lose controlofyour vehicle if you
do the following while driving:
Radjust the driver'sseat, head restraint,
steering wheel or mirrors
Rfastenthe seat belt
There isarisk of an accident.
Adjust the driver's seat, head restraint,
steering wheel and mirror and fasten your
seat belt before startingthe engine.
XObserve the safety guidelines on seat
adjustment (Ypage 99).
XMake sure that seat$is adjusted
properly.
Electrical seat adjustment (Ypage 100)
When adjusting the seat, make sure that:
Ryou are as far away from the driver's air bag
as possible.
Ryou are sitting inanormal upright position.
Ryou can fasten the seat belt properly.
Ryou have moved the backrest to an almost
vertical position.
Ryou have set the seat cushion angle so that
your thighs are gently supported.
Ryou can depress the pedals properly.
XCheck whether the head restraint is
adjusted properly.
When doing so, make sure that you have
adjusted the head restraint so that the back
of your head is supported at eye level by
the center of the head restraint.
XObserve the safety guidelines on steering
wheel adjustment (Ypage 106).
XMake sure that steering wheelis
adjusted properly.
Adjustingthe steering wheel electrically
(Ypage 106)
When adjusting the steering wheel, make
sure that:
Ryou can hold the steering wheel with your
arms slightly bent.
Ryou can move your legs freely.
Ryou can see all the displays in the
instrumentcluster clearly.
XObserve the safetyguidelinesfor seat belts
(Ypage 55).
XCheck whether you have fastened seat
beltproperly (Ypage 56).
98Correct driver'sseat position
Seats, steering wheel and mirrors

Problems with the windshield wipers
ProblemPossible causes/consequences andSolutions
The windshield wipers
are jammed.
Leaves or snow, for example, may be obstructing the windshield
wiper movement.The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
or
XSwitch off the engine using the Start/Stop button and open the
driver's door.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.
The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked ataqualified specialist
workshop.
128Windshield wipers
Lights and windshield wipers

Problems with the engine
ProblemPossible causes/consequences andSolutions
The engine does not
start. The starter motor
can be heard.
RThere isamalfunction in the engine electronics.
RThere isamalfunction in the fuel supply.
XBefore attempting to start the engine again, turn the SmartKey
in the ignition back to position0or press the Start/Stop button
repeatedly until all indicator lamps in the instrumentcluster go
out.
XTry to start the engine again (Ypage 149). Avoid excessively
long and frequent attemptstostart the engine as these will drain
the battery.
If the engine does not start after several attempts:
XConsultaqualified specialist workshop.
The engine does not
start.You cannot hear
the starter motor.
The on-board voltage is too low because the battery is too weak
or discharged.
XJump-startthe vehicle (Ypage 326).
If the engine does not start despite attemptstojump-start it:
XConsultaqualified specialist workshop.
The starter motor was exposed toathermal load that was too high.
XAllow the starter motor to cool down for approximately two
minutes.
XTry to start the engine again.
If the engine still does not start:
XConsultaqualified specialist workshop.
The engine is not
running smoothly and
is misfiring.
There isamalfunction in the engine electronics or inamechanical
componentofthe engine management system.
XOnly depress the accelerator pedal slightly.
XHave the cause rectified immediately ataqualified specialist
workshop.
Otherwise, non-combusted fuel may get into the catalytic
converter and damage it.
The coolant
temperature gauge
showsavalue above
248‡(120 †).
The coolant level is too low. The coolant is too hot and the engine
is no longer being cooled sufficiently.
XStop as soon as possible and allow the engine and the coolant
to cool down.
XCheck the coolant level (Ypage 308). Observe the warning
notes as you do so and add coolant if necessary.
154Driving
Driving and parking

Automatictransmission
Important safety notes
GWARNING
If theenginespeedisabovetheidlingspeed
and you engage transmission positionDor
R,thevehiclecould pull away suddenly. There
isariskofanaccident.
When engagingtransmission positionDorR,
always firmly depress thebrakepedal and do
notsimultaneously accelerate.
GWARNING
The automatic transmission switches to
neutral positionNwhen you switchoff the
engine. The vehicle may roll away. There is a
risk of an accident.
After switching off the engine, always switch
to parking positionP.Prevent the parked
vehicle fromrolling away by applying the
parking brake.
Selector lever
Overview of transmission positions
Selector lever in AMG vehicles withPbutton
Park position with parking lock
\nReverse gear
Neutral
Drive
Transmission position and drive
program display
!If the transmission position display in the
multifunction display is not working, you
should pull away carefully to check whether
the desired transmission position is
engaged. Ideally,you should select
transmission positionDand drive program
C.Donot restrictthe shift range.
Transmission position display
Drive program display
The current position of the selector lever is
shown by the indicators next to the selector
lever.
The indicators light up when the SmartKey is
inserted into the ignition lock. The indicators
go out when the SmartKey is removed from
the ignition lock.
DIRECT SELECTlever
Overview of transmission positions
Park position with parking lock
\nReverse gear
Neutral
Drive
Automatic transmission155
Driving and parking
Z

Xinsert the fuel filler cap intothe holder on
the insideoffuel filler flap.
XCompletely insert the filler neckofthe fuel
pump nozzle into the tank,hook in place
and refuel.
XOnly fill the tank until the pump nozzle
switches off.
iDo not add any more fuel after the pump
stops filling for the first time. Otherwise,
fuel may leak out.
Closing the fuel filler flap
XReplace the cap on the filler neck and turn
clockwise until it engages audibly.
XClose the fuel filler flap.
iClose the fuel filler flap before locking the
vehicle. Otherwise, the locking pin of the
central locking prevents the fuel filler flap
from closing.
iIf you are driving with the fuel filler cap
open, thereserve fuel warning lamp
flashes.Amessage appears in the
multifunction display (Ypage 251).
In addition, the\nCheck Engine warning
lamp may light up (Ypage 273).
For further information on warning and
indicator lamps in the instrument cluster,
see (Ypage 273).
Fuel filler flap emergency release
Xopen the trunklid.
XSlide down the parcel net.
XOpen the right-handside trim panel.
XRemove the first-aid kit (Ypage 320).
XDetach the emergencyrelease from
retainer.
XPull the emergency release in the direction
of arrow.
The fuel filler flap is unlocked.
XOpen the fuel filler flap.
166Refueling
Driving and parking

Servicing the brakes
!If the red brake warning lamp lights up in
the instrumentcluster and you hear a
warningtonewhile the engine is running,
the brakefluid level may be too low.
Observe additional warningmessages in
the multifunction display.
The brakefluid level may be too low due to
brakepad wear or leakingbrakelines.
Have the brakesystem checked
immediately. This work should be carried
out ataqualified specialist workshop.
!Vehicles with 4MATIC:function or
performancetests may only be carried out
ona2-axle dynamometer. If you are
planning to have the vehicle tested on such
adynamometer, contactanauthorized
Mercedes-BenzCenter to obtain further
information first. Otherwise, you could
damage the drive train or the brakesystem.
!Vehicles with 4MATIC:as the ESP®
system operates automatically, the engine
and the ignition must be switched off
(SmartKey in position0or1in the ignition
lock or Start/Stop button in position0or
1)while the parking brakeisbeing tested
onabrakedynamometer.
Brakingmaneuvers triggeredautomatically
by ESP®may seriouslydamagethebrake
system.
!Vehicles with 4MATIC:as theESP®
system operatesautomatically, theengine
and theignition system must be switched
off (SmartKey in position0or1in the
ignition lockorStart/Stopbuttonin
position0or1)when:
Rtesting theparking brakeonabrake
dynamometer.
Ryou intendtohave thevehicletowed with
oneoftheaxlesraised.
Braking maneuvers triggered automatically
by ESP®may seriouslydamagethebrake
system.
All checksand maintenance work on the
brakesystem must be carried out at a
qualified specialist workshop. Consult a
qualified specialist workshoptoarrangethis.
Havebrakepads installed and brakefluid
replacedataqualified specialist workshop.
If thebrakesystem has only been subject to
moderateloads,you should test the
functionalityofyour brakes at regular
intervals. To do so, press firmly on thebrake
pedal when driving atahigh speed. This
improvesthegripofthebrakepads.
You can findadescription of Brake Assist
(BAS) on (Ypage 67)orofBASPLUSon
(Ypage 67).
The braking characteristics of thevehiclecan
be seriouslyimpaired if:
Rbrakepads other than those recommended
are installed
Rtherecommended brakefluid is notused
Safe braking can no longer be guaranteed.
AMG high-performance and ceramic
brakes
The high-performance brake system is
installed only on the CLS 63 AMG.
The AMG brake systems are designed for
heavy loads. This may lead to noise when
braking. This will depend on:
RSpeed
RBraking force
REnvironmental conditions, such as
temperature and humidity
The wear of individualcomponentsofthe
brake system, such as the brake pads/linings
or brake discs, depends on the individual
driving style and operating conditions.
For this reason, it is impossibletostate a
mileage that will be valid under all
circumstances. An aggressive driving style
will lead to high wear. You can obtain further
information aboutthis from your authorized
Mercedes-BenzCenter.
Driving tips173
Driving and parking
Z