2014 MERCEDES-BENZ CLS lock

Warning displays
Warning display for the front area
Segments on the left-hand side of the
vehicle
Segments on the right-hand side of the
vehicle
$Segments showing operational readiness
The warning displays show the distance
between the sensors and the obstacle. The
warning displayfor the front area is located
on the dashboard above the center airvents.
The warning display for the rear area is
located on the headliner in the rear
compartment.
The warning display for each side of the
vehicle is divided intofive yellow and two red
segments. PARKTRONIC is operational if
yellow segments showing operational
readiness$light up.
The selected transmission position and the
direction in which the vehicle is rolling
determine which warning display is active
when the engineisrunning.
Transmission
position
Warning display
DFrontarea activated
R,Nor the vehicle
is rolling
backwards
Rear and frontareas
activated
PNo areas activated
One or more segments light up as the vehicle
approaches an obstacle, depending on the
vehicle's distancefrom the obstacle.
From the:
Rsixthsegmentonwards,youwill hearan
intermittentwarningtonefor
approximately two seconds.
Rseventhsegment onwards, you will hear a
warning tonefor approximately two
seconds. This indicates that you have now
reached the minimum distance.
Deactivating/activating PARKTRONIC
Indicator lamp
To deactivate/activate PARKTRONIC
If indicator lamplights up, PARKTRONIC is
deactivated. Active Parking Assist is then also
deactivated.
iPARKTRONIC is automatically activated
when you turn the SmartKey to position2
in the ignition lock.
Driving systems195
Driving and parking
Z

Parking tips:
ROn narrow roads, drive as close to the
parking space as possible.
RParking spaces that are littered or
overgrown might be identified or measured
incorrectly.
RParking spaces that are partially occupied
by trailer drawbars might not be identified
as such or be measured incorrectly.
RSnowfall or heavy rain may lead toaparking
space being measured inaccurately.
RPay attention to the PARKTRONIC
(Ypage 195) warning messages during the
parking procedure.
RYou can intervene in the steeringprocedure
to correctitatany time. Active Parking
Assist will then be canceled.
RWhen transportingaload which protrudes
from your vehicle, you should not use
Active Parking Assist.
RNever use Active Parking Assist when snow
chains are installed.
RMake sure that the tire pressures are
alwayscorrect. This hasadirectinfluence
on the parking characteristics of the
vehicle.
Use Active Parking Assist for parking spaces:
Rthatare paralleltothe direction of travel
Rthat are on straight roads, not bends
Rthat are on the same levelasthe road,e.g.
not on the pavement
Detectingparking spaces
Objects located above the height range of
Active Parking Assist willnot be detected
when the parking space is measured. These
are not taken into account when the parking
procedure is calculated,e.g. overhanging
loads, tail sections or loading ramps of goods
vehicles.
GWARNING
If there are objects above the detection range,
Active Parking Assist may turn prematurely.
You may causeacollision asaresult. There is
arisk of an accident.
If there are objects above the detection range,
stop and deactivate Active Parking Assist.
For further information on the detection
range (Ypage194).
Active Parking Assist does not support you
with parking spaces paralleltothe direction
of travel if:
Rthe parking space is onacurb
Rtheparking spaceappearsblockedtothe
system, for example,byfoliage or grass
pavingblocks
Rthearea that thevehicleneeds to
maneuveristoo small
Rthe parking space is bordered by an
obstacle, such asatree,apost oratrailer
Example: detected parking space
Detected parking space on the left
Parking symbol
$Detected parking space on the right
Active Parking Assist is switched on
automaticallywhen driving forwards. The
system is operational at speeds of up to
approximately 22 mph (35 km/h). While in
operation, the system independently locates
and measures parking spaces on both sides
of the vehicle.
Active Parking Assist will only detect parking
spaces:
Rthat are parallel to the direction of travel
Rthat are at least 59 in (1.5 m) wide
Rthat are at least 51 in (1.3 m) longer than
your vehicle
When driving at speeds below 19 mph
(30 km/h), you will see parking symbol as a
Driving systems197
Driving and parking
Z

Rif the camera is exposed to very bright light
Rif the area is lit by fluorescentlight or LED
lighting (thedisplay may flicker)
Rif there isasudden change in temperature,
e.g. when drivingintoaheatedgarage in
winter
Rif the camera lens is dirtyorobstructed
Rif the rear of your vehicle is damaged. In
this event, have the camera position and
settingchecked ataqualified specialist
workshop.
General notes
Example: Coupe
Rear view camerais located in the handle
strip of the trunk lid.
Rear view camerais an optical parking and
maneuveringaid. It shows the area behind
your vehicle with guide lines in the COMAND
display.
The area behindthe vehicle is displayed as a
mirror image, as in the rear view mirror.
iThe textofmessages shown in the
COMAND display depends on the language
setting. The following are examples of rear
view camera messages in the COMAND
display.
Activating/deactivating the rear view
camera
XTo activate:make sure that the SmartKey
is in position2in the ignition lock.
XMake sure that the "Activation byRgear"
setting is active in COMAND,see the
separate COMAND operatinginstructions.
XEngage reversegear.
The area behind the vehicle is shown in the
COMAND display with guide lines.
To deactivate:the rear view camera is
deactivated if you:
Rshift the transmission to positionP
Rdrive 33 ft (10 m) forwards
Rshift the transmission fromRto another
position after 15 seconds
Rdrive forwards ataspeed of over5mph
(10 km/h)
Displays in the COMAND display
The rear view camera may showadistorted
view of obstacles, show them incorrectly or
not at all. The rear view camera does not show
objects in the following positions:
Rvery close to the rear bumper
Runder the rear bumper
Rin the area immediately above the tailgate
handle
!Objects not at ground level may appear to
be further away than they actually are, e.g.:
Rthe bumper ofaparked vehicle
Rthe drawbar ofatrailer
Rthe ball coupling ofatrailer tow hitch
Rthe rear section of an HGV
Raslanted post
Use the guidelines only for orientation.
Approachobjects no further than the
bottom-most guideline.
200Driving systems
Driving and parking

highlighted in the Night View Assist Plus
display.
Light from the headlamps of oncoming
vehicles does not affect the Night View Assist
Plus displayinthe multifunction display. This
is also the case if you cannot switch on the
high-beam headlamps due to oncoming
traffic.
iInfrared light is not visible to the human
eye and therefore does not glare. Night
View Assist Plus can therefore remain
switched on even if there is oncoming
traffic.
Activating Night View Assist Plus
Activation conditions
You can only activate Night View Assist Plus
if:
Rthe SmartKey is in position2in the ignition
lock.
Rit is dark.
Rthe light switch is in the\ror
position.
Rreverse gear has not been engaged.
Activating Night View Assist Plus
XMake sure that COMAND is switched on.
XPress button.
The Night View Assist Plus displayappears
in the COMAND display.
You can read about how to adjust the
brightness of the COMAND displayinthe
COMAND operating instructions.
iThe infrared headlamps only switch on
when the vehicle is being driven at speeds
of approximately6mph (10 km/h). This
means that you do not have the full visual
range while the vehicle is stationary and
cannot check whether Night View Assist
Plus is working.
Pedestrian recognition
Night View Assist Plus display
Pedestrian recognized
$Framing
!Symbol for active pedestrian recognition
iAnimals are not recognized by pedestrian
recognition.
Night View Assist Plus is able to recognize
pedestrians by typical characteristics, e.g. a
silhouette in the shape ofaperson.
Pedestrian recognition is then switched on
automatically:
Rif Night View Assist Plus is activated
Rif you are driving faster than approximately
6mph (10 km/h)
Rthe surroundings are dark, e.g. when
driving outside built-up areas without
street lighting
If pedestrian recognition is active,
symbol!appears. If pedestriansare
detected, they are highlighted with framing
$.Ifthe pedestrian recognition system has
broughtapedestrian to your attention, look
through the windshield to evaluate the
situation. The actual distance to objectsand
Driving systems205
Driving and parking
Z

indicator lamp goes out and BlindSpot Assist
is operational.
Ifavehicle is detected within the monitoring
rangeofBlindSpot Assist at speeds above
20 mph (30 km/h), warninglampon the
correspondingside lightsupred. This warning
is always emitted whenavehicle enters the
blind spot monitoring rangefrom behind or
from the side.When you overtakeavehicle,
the warning only occurs if the difference in
speed is less than7mph (12km/h).
The yellow indicator lamp goes out if reverse
gear is engaged. In this event,Blind Spot
Assist is no longer active.
The brightness of the indicator/warning
lamps is adjusted automatically according to
the ambient light.
Collision warning
Ifavehicle is detected in the monitoring range
of Blind Spot Assist and you switchonthe
correspondingturn signal,adouble warning
tonesounds. Red warning lampflashes. If
the turn signal remains on, vehicles detected
are indicated by the flashing of red warning
lamp.There are no further warning tones.
Switching on Blind Spot Assist
XMake sure that Blind Spot Assist
(Ypage 228) is activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Lane Keeping Assist
Important safety notes
GWARNING
Lane Keeping Assist may not always clearly
recognizelane markings.
In this case, Lane Keeping Assist may:
Rgive an unnecessary warning
Rnot giveawarning
There isarisk of an accident.
Always pay particular attention to the traffic
situation and stay in lane, in particular if
warned by Lane Keeping Assist.
GWARNING
The Lane Keeping Assist warning does not
return the vehicle to the original lane. There
isarisk of an accident.
You should always steer, brake or accelerate
yourself, in particular if warned by Lane
Keeping Assist.
If you fail to adapt your driving style, Lane
Keeping Assist can neither reduce the risk of
an accident nor override the laws of physics.
Lane Keeping Assist cannot take into account
the road, traffic and weather conditions. Lane
Keeping Assist is merely an aid. You are
responsible for the distance to the vehicle in
front,for vehicle speed, for braking in good
time and for staying in your lane.
The Lane Keeping Assist does not keep the
vehicle in the lane.
The system may be impaired or may not
function if:
Rthere is poor visibility, e.g. due to
insufficient illumination of the road, or due
to snow, rain, fog or spray
Rthere is glare, e.g. from oncomingtraffic,
the sun or reflections (e.g. when the road
surface is wet)
Rthe windshield is dirty, fogged up, damaged
or covered, for instancebyasticker, in the
vicinity of the camera
Rthere are no, several or unclear lane
markings foralane, e.g. in areas with road
construction work
Rthe lane markings are worn away,dark or
covered up, e.g. by dirt or snow
Driving systems209
Driving and parking
Z

The brightness of the indicator/warning
lamps is adjusted automatically accordingto
the ambient light.
Visual and acoustic collision warning
If you switch on the turn signals to change
lanes andavehicle is detected in the side
monitoring range, you receiveavisual and
acoustic collision warning. You then hear a
double warning toneand red warning
lampflashes. If the turn signal remains on,
detected vehicles are indicated by the
flashing of red warning lamp.There are no
further warning tones.
Course-correcting brake application
GWARNING
Acourse-correctingbrake application cannot
alwayspreventacollision. There isarisk of
an accident.
Always steer, brake or accelerate yourself,
especially if Active Blind Spot Assist warns
you or makesacourse-correcting brake
application. Always maintainasafe distance
at the sides.
If Active Blind Spot Assist detectsarisk of a
lateral collision in the monitoring range, a
course-correcting brake application is carried
out. This is meant to assist you in avoiding a
collision.
Ifacourse-correcting brake application
occurs, red warning lampflashes in the
exterior mirror andadual warning tone
sounds. In addition, the display shown in the
lower image appears in the multifunction
display.
In very rare cases, the system may make an
inappropriate brake application. An
inappropriate course-correcting brake
application may be interrupted at any time if
you steer slightly in the opposite direction or
accelerate, for example.
The course-correcting brake application is
available in the speed range between
20 mph (30 km/h) and 120 mph (200 km/h).
Either no braking application, oracourse-
correcting brake application adapted to the
driving situation occurs if:
Rthere are vehicles or obstacles, e.g. crash
barriers, located on both sides of your
vehicle.
Ravehicle approaches you too closely at the
side.
Ryou have adoptedasporty driving style with
high cornering speeds.
Ryou clearly brake or accelerate.
Radriving safety system intervenes, e.g.
ESP®or PRE-SAFE®Brake.
RESP®is switched off.
Raloss of tire pressure oradefectivetire is
detected.
Switching on Active Blind Spot Assist
XMake sure that the radar sensor system
(Ypage 232) and Active Blind Spot Assist
(Ypage 228) are activated in the on-board
computer.
XTurn the SmartKey to position2in the
ignition lock.
Warning lampsin the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Driving systems213
Driving and parking
Z

Outsidetemperature display
You should pay special attention to road
conditions when temperatures are around
freezing point.
The outside temperature display is in the
multifunction display (Ypage 221).
Changes in the outside temperature are
displayed afterashort delay.
Speedometer with segments
The segments in the speedometer indicate
which speed range is available.
RCruise control activated (Ypage 175):
The segments light up from the stored
speed to the maximum speed.
RDISTRONIC PLUS activated (Ypage 177):
One or two segments in the set speed
range light up.
RDISTRONIC PLUS detectsavehicle in front:
The segments between the speed of the
vehicle in frontand the stored speed light
up.
Operatingthe on-board computer
Overview
Multifunctiondisplay
Right control panel
$Switches on the VoiceControl System;
see the separateoperating instructions
!Backbutton
Left control panel
XTo activatethe on-board computer:turn
the SmartKey to position1in the ignition
lock.
You can control the multifunction displayand
the settings in the on-board computer using
the buttons on the multifunction steering
wheel.
220Displays and operation
On-board computer and displays

XPressorto select theDay
Lights:function.
If theDayLights:have been switched on,
the cone of light and thesymbol in
the multifunction display are shown in red.
XPress thebutton to save the setting.
Further information on daytime running
lamps (Ypage 117).
Setting the brightness of the ambient
lighting
XPress the\norbutton on the
steeringwheel to select theSett.menu.
XPress theorbutton to select the
Lightssubmenu.
XPressto confirm.
XPress theorbutton to select the
Amb. Light +/-.function.
You will see the selected setting.
XPressto confirm.
XPress theorbutton to adjust the
brightness to any level fromOfftoLevel
5(bright).
XPress theorbutton to save the
setting.
Setting the ambient lighting color
XPress the\norbutton on the
steeringwheel to select theSett.menu.
XPress theorbutton to select the
Lightssubmenu.
XPressto confirm.
XPress theorbutton to select the
Ambient Light Colorfunction.
XPressto confirm.
XPress theorbutton to set the
color toSOLAR,NEUTRALorPOLAR.
XPress theorbutton to save the
setting.
Activating/deactivating surround
lighting and exterior lighting delayed
switch-off
XPress the\norbutton on the
steeringwheel to select theSett.menu.
XPress theorbutton to select the
Lightssubmenu.
XPressto confirm.
XPressorto select the
Surround Lightingfunction.
When theSurround Lightingfunction is
activated, the light cone and the area
around the vehicle are displayedinred in
the multifunction display.
XPress thebutton to save the setting.
Deactivating delayed switch-off of the
exterior lighting temporarily:
XBefore leaving the vehicle, turn the
SmartKey to position0in the ignition lock.
XTurn the SmartKey to position2in the
ignition lock.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the
engine.
If you have activated theSurround
Lightingfunction and the light switch is set
to\r,the following functions are activated
when it is dark:
RSurround lighting:the exterior lighting
remains lit for 40 seconds after unlocking
with the SmartKey. If you start the engine,
the surround lighting is switched off and
the automatic headlamp mode is activated
(Ypage 117).
RExterior lighting delayed switch-off:the
exterior lighting remains lit for 60seconds
after the engine is switched off. If you close
all the doors and the trunklid, the exterior
lighting goes off after5seconds.
iDepending on your vehicle's equipment,
when the surround lighting and delayed
Menus and submenus231
On-boar dc omputer and displays
Z