2014 MAZDA MODEL CX-9 radio antenna

Black plate (223,1)
NOTElDo not install any accessories within the detection ranges of the sensors. It may affect the system
operation.
lDepending on the type of obstruction and the surrounding conditions, the detection range of a
sensor may narrow, or the sensors may not be able to detect obstructions.
lThe system may not operate normally under the following conditions:lMud, ice, or snow is adhering to the sensor area (Returns to normal operation when removed).lThe sensor area is frozen (Returns to normal operation when the ice is thawed).lThe sensor is covered by a hand.lThe sensor is excessively shocked.lThe vehicle is excessively tilted.lUnder extremely hot or cold weather conditions.lThe vehicle is driven on bumps, inclines, gravel, or grass covered roads.lAnything which generates ultrasound is near the vehicle, such as another vehicle's horn, the
engine sound of a motorcycle, the air brake sound of a large-sized vehicle, or another vehicle's
sensors.
lThe vehicle is driven in heavy rain or in road conditions causing water-splash.lA commercially-available fender pole or an antenna for a radio transmitter is installed to the
vehicle.
lThe vehicle is moving towards a tall or square curbstone.lAn obstruction is too close to the sensor.lObstructions under the bumper may not be detected. Obstructions that are lower than the bumper
or thin which may have been initially detected but are no longer detected as the vehicle
approaches more closely.
lThe following types obstructions may not be detected:lThin objects such as wire or ropelThings which absorb sonic waves easily such as cotton or snowlAngular shaped objectslVery tall objects, and those which are wide at the toplSmall, short objectslAlways have the system inspected at an Authorized Mazda Dealer if any shock is applied to the
bumpers, even in a minor accident. If the sensors are deviated, they cannot detect obstructions.
lThe system may have a malfunction if the beep does not operate or the indicator light does not
illuminate when the park assist sensors switch is turned on. Consult an Authorized Mazda Dealer.
lThe system may have a malfunction if the beep sound which indicates a system malfunction is
heard and the indicator light flashes. Consult an Authorized Mazda Dealer.
lThe beeper which indicates a system malfunction may not be heard if the ambient temperature is
extremely cold, or mud, ice, or snow adheres to the sensor area. Remove any foreign material
from the sensor area.
Driving Your Mazda
Starting and Driving
5-47
CX-9_8DA3-EA-13G_Edition2 Page223
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (270,1)
5. Press and hold the just-trainedHomeLink button and observe the
indicator light.
If the indicator light stays on constantly,
programming is complete and your
device should activate when the
HomeLink button is pressed and released.
NOTE
To program the remaining two HomeLink
buttons, begin with “Programming ”―step 2.
Do not repeat step 1.
If the indicator light blinks rapidly for
two seconds and then turns to a
constant light, continue with
“ Programming ”steps 6 ―8to complete
the programming of a rolling code
equipped device (most commonly a
garage door opener).
6. At the garage door opener receiver (motor-head unit) in the garage, locate
the “learn ”or “smart ”button. This can
usually be found where the hanging
antenna wire is attached to the motor-
head unit.
7. Firmly press and release the “learn ”or
“ smart ”button. (The name and color of
the button may vary by manufacturer.)
NOTE
There are 30 seconds in which to initiate step
8.
8. Return to the vehicle and firmly press,
hold for two seconds and release the
programmed HomeLink button. Repeat
the “press/hold/release ”sequence a
second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process. HomeLink should now activate your
rolling code equipped device.
NOTE
To program the remaining two HomeLink
buttons, begin with
“Programming ”―step 2.
Do not repeat step 1.
For questions or comments, please contact
HomeLink at www.homelink.com or1-
800-355-3515.
Gate operator/Canadian Programming
Canadian radio-frequency laws require
transmitter signals to “time-out ”(or quit)
after several seconds of transmission ―
which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are
designed to “time-out ”in the same
manner.
If you live in Canada or you are having
difficulties programming a gate operator
by using the “Programming ”procedures
(regardless of where you live), replace
“ Programming HomeLink ”step 3 with
the following:
NOTE
If programming a garage door opener or gate
operator, it is advised to unplug the device
during the “cycling ”process to prevent
possible overheating.
Continue to press and hold the HomeLink
button while you press and release ―
every two seconds (“ cycle ”) your hand-
held transmitter until the frequency signal
has successfully been accepted by
HomeLink. (The indicator light will flash
slowly and then rapidly.) Proceed with
“ Programming ”step 4 to complete.
5-94
Driving Your Mazda
Switches and Controls
CX-9_8DA3-EA-13G_Edition2 Page270
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (289,1)
Antenna
qAM/FM Radio Antenna
The antenna is printed onto the window
glass.
CAUTION
When washing the inside of the
window which has an antenna, use a
soft cloth dampened in lukewarm
water, gently wiping the antenna
lines.
Use of glass cleaning products could
damage the antenna.
qSatellite Radio Antennaí
The satellite radio antenna receives
SIRIUS signals.
Satellite radio antenna
Operating Tips for Audio
System
WARNING
Do not adjust the audio control
switches while driving the vehicle:
Adjusting the audio while driving the
vehicle is dangerous as it could
distract your attention from the
vehicle operation which could lead to
a serious accident. Always adjust the
audio while the vehicle is stopped.
Even if the audio control switches are
equipped on the steering wheel, learn
to use the switches without looking
down at them so that you can keep
your maximum attention on the road
while driving the vehicle.
CAUTION
ØFor the purposes of safe driving,
adjust the audio volume to a level
that allows you to hear sounds
outside of the vehicle including car
horns and particularly emergency
vehicle sirens.
Ø Do not install non-genuine
speakers since their vibration may
affect the Dynamic Stability
Control (DSC)/Roll Stability
Control (RSC) sensors.
NOTE
lTo prevent the battery from being
discharged, do not leave the audio system
on for a long period of time when the
engine is not running.
lIf a cellular phone or CB radio is used in
or near the vehicle, it could cause noise to
occur from the audio system, however, this
does not indicate that the system has been
damaged.
Interior Comfort
Audio System
6-17íSome models.
CX-9_8DA3-EA-13G_Edition2 Page289
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (421,1)
Safety Certification
FCC
FCC: CB2MAZGEN6HFT
NOTE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may causeundesired operation.
WARNING
Changes or modifications made to this equipment not expressly approved by the
manufacturer may void the FCC authorization to operate this equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
lReorient or relocate the receiving antenna.lIncrease the separation between the equipment and receiver.lConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
lConsult the dealer or an experienced radio/TV technician for help.
IC
IC:279B-MAZGEN6HFT
Licence exempt
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Interior Comfort
Bluetooth®
6-149
CX-9_8DA3-EA-13G_Edition2 Page421
Monday, September 9 2013 4:9 PM
Form No.8DA3-EA-13G

Black plate (422,1)
The term“IC: ”before the radio certification number only signifies that Industry Canada
technical specifications were met. The antenna used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provided with installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
6-150
Interior Comfort
Bluetooth®
CX-9_8DA3-EA-13G_Edition2 Page422
Monday, September 9 2013 4:9 PM
Form No.8DA3-EA-13G