Black plate (188,1)
CAUTION
ØDo not adjust the vehicle height, modify the headlight units, or remove the
camera. Otherwise, the system will not operate normally.
ØHeed the following cautions to assure correct operation of the High Beam Control
System (HBC).
ØDo not place objects on the dashboard which reflect light.
ØKeep the area of the windshield glass near the Forward Sensing Camera (FSC)
clean.
ØDo not apply accessories, stickers or film to the windshield near the Forward
Sensing Camera (FSC). If there are objects in front of the Forward Sensing
Camera (FSC) lens, even a transparent sticker, they will obstruct the lens and
cause the system to not operate correctly.
ØBefore performing repairs around the rearview mirror, consult an Authorized
Mazda Dealer.
ØAlways keep the windshield glass around the Forward Sensing Camera (FSC)
clean. If the windshield fogs, defog it using the front defroster.
ØWhen cleaning the windshield, do not allow glass cleaners or similar cleaning
fluids to get on the Forward Sensing Camera (FSC) lens. In addition, do not
touch the Forward Sensing Camera (FSC) lens.
ØConsult an Authorized Mazda Dealer regarding cleaning the interior side of the
windshield around the Forward Sensing Camera (FSC).
NOTE
Under the following conditions, the timing in which the system switches the headlights changes. If the
system does not switch the headlights appropriately, manually switch between high and low beams
according to the visibility, and road and traffic conditions.
lWhen there are sources of light in the area such as street lamps, illuminated signboards, and
traffic signals.
lWhen there are reflective objects in the surrounding area such as reflective plates and signs.lWhen visibility is reduced under rain, snow and foggy conditions.lWhen driving on roads with sharp curves or undulations.lWhen the headlights/rear lamps of vehicles in front of you or in the opposite lane are dim or not
illuminated.
lWhen there is sufficient darkness such as at dawn or dusk.lWhen the luggage compartment is loaded with heavy objects or the rear passenger seats are
occupied.
lWhen visibility is reduced due to a vehicle in front of you spraying water from its tires onto your
windshield.
4-64
When Driving
Switches and Controls
Mazda6_8DQ8-EA-13L_Edition3 Page188
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (189,1)
Forward Sensing Camera (FSC)
The High Beam Control System (HBC) camera, located near the rearview mirror, also
functions as the Forward Sensing Camera (FSC) for the Lane Departure Warning System
(LDWS).
Forward Sensing Camera (FSC)
CAUTION
Heed the following cautions to assure the correct operation of the Forward Sensing
Camera (FSC).
ØDo not remove the Forward Sensing Camera (FSC) cover.
ØConsult an Authorized Mazda Dealer regarding cleaning of the camera lens.
ØDo not hit or apply strong force to the Forward Sensing Camera (FSC) or the area
around it. If the Forward Sensing Camera (FSC) has been severely hit, do not use
the High Beam Control System (HBC) and consult an Authorized Mazda Dealer.
ØConsult an Authorized Mazda Dealer before performing repairs around the
Forward Sensing Camera (FSC).
ØThe Forward Sensing Camera (FSC) is installed to the windshield. Consult an
Authorized Mazda Dealer for windshield repair and replacement.
ØThe direction in which the Forward Sensing Camera (FSC) is pointed has been
finely adjusted. Do not change the installation position of the Forward Sensing
Camera (FSC) or remove it. Otherwise, it could result in damage or malfunction.
ØBe careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get
dirty. Also, do no take the camera apart. Otherwise, it could result in damage or
malfunction.
ØAlways keep the windshield glass around the camera clean by removing dirt or
fogging. Use the windshield defroster to remove fogging on the windshield.
When Driving
Switches and Controls
4-65
Mazda6_8DQ8-EA-13L_Edition3 Page189
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (190,1)
qTo Operate the System
The High Beam Control System (HBC)
operates to switch the headlights
automatically between high and low
beams after the ignition is switched ON
and the headlight switch is in the AUTO
and high beam position. At the same time,
the High Beam Control System (HBC)
indicator light (green) in the instrument
cluster illuminates.
Refer to Warning/Indicator Lights on page
4-23.
The High Beam Control System (HBC)
determines that it is nighttime based on
the brightness of the surrounding area.
NOTE
lWhen the vehicle speed is 30 km/h (18 mph)
or higher, the headlights automatically
switch to high beams when there are no
vehicles in front of your vehicle or
approaching in the opposite direction.
When the vehicle speed is less than about
20 km/h (12 mph), the High Beam Control
System (HBC) switches the headlights to
low beams.
lThe low beams may not switch to high
beams when cornering the vehicle.
lOperation of the High Beam Control
System (HBC) function can be
disabled.Refer to Personalization Features
on page 9-9.
qManual Switching
Switching to low beams
Shift the lever to the low beam position.
The High Beam Control System (HBC)
indicator light (Green) turns off.
Switching to high beams
Turn the headlight switch to the
position.
The High Beam Control System (HBC)
indicator light (Green) turns off and the
is illuminated.
4-66
When Driving
Switches and Controls
Mazda6_8DQ8-EA-13L_Edition3 Page190
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (191,1)
Fog Lightsí
Use this switch to turn on the fog lights.
The fog lights will improve visibility at
night and during foggy conditions.
To turn the fog lights on, rotate the fog
light switch to the
position.
The headlight switch must be in the
position before turning on the fog lights.
Fog light switch
To turn the fog lights off, rotate the fog
light switch to the
position or turn
the headlight switch to the
or
position.
NOTE
lThe fog lights will turn off when the
headlights are set at high beams.
l(With auto-light control)
If the fog light switch is in the
position
and the headlight switch is in the
position, the fog lights will turn on when
the headlights, the exterior lights and
dashboard illumination turn on.
Turn and Lane-Change
Signals
NOTElIf an indicator light stays on without
flashing or if it flashes abnormally, one of
the turn signal bulbs may be burned out.
lA personalized function is available to
change the turn indicator sound volume.
Refer to Personalization Features on page
9-9.
qTurn Signals
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Right turn
Left turn Right lane change
Left lane changeOFF
Green indicators on the dashboard show
which signal is working.
When Driving
Switches and Controls
4-67íSome models. Mazda6_8DQ8-EA-13L_Edition3 Page191
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (213,1)
NOTElThe Smart City Brake Support (SCBS) system will not operate if the driver is deliberately
performing driving operations (accelerator pedal and steering wheel).
lThe Smart City Brake Support (SCBS) system will operate under the following conditions.lThe engine is running.lThe display in the instrument cluster does not indicate that the system requires inspection or it
cannot be used.
lThe vehicle speed is between about 4 to 30 km/h (2 to 18 mph).lThe Smart City Brake Support (SCBS) system is not turned off.lThe DSC operation is not turned off using the DSC OFF switch.lThe DSC is not malfunctioning.lThe Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-infrared laser
beam and receiving the beam reflected off the reflector of the vehicle ahead, and then using it for
the measurement. Consequently, the Smart City Brake Support (SCBS) may not operate under the
following conditions:
lReflection of the laser is poor due to the shape of the vehicle ahead.lThe vehicle ahead is significantly dirty.lUnder bad weather condition, such as rain, fog and snow.lThe window washer is being used or the windshield wipers are not used when it's raining.lThe windshield is dirty.lThe steering wheel is turned completely left or right, or the vehicle is accelerated rapidly and
comes close to the vehicle ahead.
lTrucks with low loading platforms and vehicles with an extremely low or high profile.lVehicles with certain shapes such as a vehicle carrier.lUnder the following conditions, the Smart City Brake Support (SCBS) system may not operate
normally.
lHeavy luggage is loaded in the luggage compartment or on the rear seat.lIf there is the possibility of partial contact with a vehicle ahead.lWhen driving on continuously curving roads, and entering and exiting exits.lElongated luggage or cargo is loaded onto installed roof rails and covers the laser sensor.lExhaust gas from the vehicle in front, sand, snow, and water vapor rising from manholes and
grating, and water splashed into the air.
lWhen towing a malfunctioning vehicle.lIn the following cases, the laser sensor may inadvertently determine that there is a vehicle ahead
and the Smart City Brake Support (SCBS) system may operate.
lObjects on the road at the entrance to a curve.lVehicles passing in the opposite lane while making a curve.lMetal objects, bumps, or protruding objects on the road.lWhen passing through a toll gate.lWhen passing under a vinyl curtain or flag.lPlastic objects such as pylons.lTwo-wheeled vehicles, pedestrians, animals or standing trees.lVehicle is driven with some of the tires having significant wear.
When Driving
Brake
4-89
Mazda6_8DQ8-EA-13L_Edition3 Page213
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (259,1)
Indication on display
NOTElIf the LDWS warning sound is set to
rumble, the sound will be heard from the
vehicle speaker on the side which the
system determined the vehicle may be
deviating from its lane.
lThe LDWS warning sound may not be
heard depending on the surrounding
conditions such as outside noise.
lThe warning timing with which the system
determines the vehicle may be deviating
from its lane can be changed.
Refer to Personalization Features on page
9-9.
qForward Sensing Camera (FSC)
lThe LDWS camera, located near the
rearview mirror, also functions as the
Forward Sensing Camera (FSC) for the
High Beam Control System (HBC).
lIf the temperature inside the Forward
Sensing Camera (FSC) is extremely
high or low, the LDWS is
automatically canceled and kept on
stand-by, and the LDWS warning light
(amber) in the instrument cluster
flashes. Message information is
indicated in the display in the type A
instrument cluster.
The LDWS is automatically enabled
when the conditions change and the
system is operable.
Forward Sensing Camera (FSC)
When Driving
Lane Departure Warning System (LDWS)
4-135
Mazda6_8DQ8-EA-13L_Edition3 Page259
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (263,1)
qDisplayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
(Actual view)
Object Garnish
Bumper
NOTElThe displayable range varies depending on the vehicle and road conditions.lThe displayable range is limited. Objects under the bumper or around the bumper ends cannot be
displayed.
lThe distance appearing in the displayed image is different from the actual distance because the
rear view parking camera is equipped with a specific lens.
lSome optionally installed vehicle accessories may be picked up by the camera. Do not install any
optional parts that can interfere with the camera view, such as illuminating parts or parts made of
reflective material.
lIt may be difficult to see the display under the following conditions, however, it does not indicate a
malfunction.
lIn darkened areas.lWhen the temperature around the lens is high/low.lWhen the camera is wet such as on a rainy day or during periods of high humidity.lWhen foreign material such as mud is stuck around the camera.lWhen the camera lens reflects sunlight or headlight beams.lImage display may be delayed if the temperature around the camera is low.
When Driving
Rear View Monitor
4-139
Mazda6_8DQ8-EA-13L_Edition3 Page263
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L
Black plate (286,1)
Do not spill any liquid on the audio
system.
Do not insert any objects, other than CDs,
into the slot.
qRadio Reception
AM characteristics
AM signals bend around such things as
buildings or mountains and bounce off the
ionosphere.
Therefore, they can reach longer distances
than FM signals.
Because of this, two stations may
sometimes be picked up on the same
frequency at the same time.
Station 2 Station 1Ionosphere
FM characteristics
An FM broadcast range is usually about
40―50 km (25―30 miles) from the
source. Because of extra coding needed to
break the sound into two channels, stereo
FM has even less range than monaural
(non-stereo) FM.
FM Station
40—50km
(25—30 miles)
Signals from an FM transmitter are similar
to beams of light because they do not
bend around corners, but they do reflect.
Unlike AM signals, FM signals cannot
travel beyond the horizon. Therefore, FM
stations cannot be received at the great
distances possible with AM reception.
AM wave FM wave
FM wave
100—200 km (60—120 miles)Ionosphere
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days
may provide better reception than clear
days.
5-14
Interior Features
Audio System
Mazda6_8DQ8-EA-13L_Edition3 Page286
Friday, June 13 2014 6:22 PM
Form No.8DQ8-EA-13L