2014 LEXUS LX570 lock

661-2. Opening, closing and locking the doors
LX570_OM_OM60L21U_(U) NOTICE■
To prevent back door closer malfunction
Do not apply excessive force to the back d oor while the back door closer is operat-
ing. ■
To prevent damage to the power back door ●
Make sure that there is no ice between the back door and frame that would pre-
vent movement of the back door. Operating the power back door when exces-
sive load is present on the back door may cause a malfunction. ●
Do not apply excessive force to the back door while the power back door is oper-
ating. ●
Take care not to damage the sensors (installed on the right and left edges of the
power back door) with a knife or other sharp object. If the sensor is disconnected,
the power back door will not operate in automatic operation.

691-3. Adjustable components (s eats, mirrors, steering wheel)
1
Before driving
LX570_OM_OM60L21U_(U) Active head restraint
When the occupant’s lower back
presses against the seatback dur-
ing a rear-end collision, the head
restraint moves slightly forward
and upward to help reduce the risk
of whiplash on the seat occupant.■
The auto away function for exiting the driver seat
If the seat is already close to the rearmost position, the auto away function may not
operate when the driver exits the vehicle. ■
Active head restraint
Even small forces applied to the seatback may cause the head restraint to move.
Pushing up a locked head restraint forcibly may make the inner structure of the
head restraint appear. This does not indicate a problem.
During
rear-end
collision
Inner
structure

821-3. Adjustable components (s eats, mirrors, steering wheel)
LX570_OM_OM60L21U_(U) CAUTION■
Seat adjustment
Do not recline the seat more than necessary when the vehicle is in motion to reduce
the risk of sliding under the lap belt.
If the seat is too reclined, during an accide nt the lap belt may sl ide past the hips and
apply restraint forces directly to the abdomen or your neck may contact the shoul-
der belt, increasing the risk of death or serious injury. ■
When the seatback is folded ●
Do not sit on or place anything on the seatback while driving. ●
Be sure to install the seat hook covers on the seat hooks, or you may get burned
when they become hot.■
When returning the seatbacks to their original position
Observe the following precautions. Failure to do so may result in death or serious
injury. ●
Be careful not to get your hands or feet pinched in the seat. ●
Make sure the seats are securely locked. Fa ilure to do so will prevent the seat belt
from operating properly. ●
Check that the seat belts are not twisted or caught under the seat.●
Arrange the seat belts in the proper positions for ready use.■
Avoiding damage to seat components
Do not hang or attach anythi ng on the seatback striker.
NOTICE■
Before tumbling, folding up the seats
The seat belts and buckles must be stowed. ■
After returning the third seat
Make sure that the handle on the re ar of the seatback has been secured.

8311-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
LX570_OM_OM60L21U_(U) Driving position memory system Your preferred driving position (the po sition of the driver’s seat, steering
wheel and outside rear view mirrors) can be entered into the computer’s
memory and recalled with the touch of a button. It is also possible to set this
function to activate automatica lly when the doors are unlocked.
Three different driving positions can be entered into memory.
■ Entering a position to memory
Turn the “ENGINE START STOP ” switch to IGNITION ON
mode.
Adjust the driver’s seat, steeri ng wheel, and outside rear view
mirrors to the desired positions.
While pressing the “SET” but-
ton, or within 3 seconds after
the “SET” button is pressed,
press and hold button “1”, “2” or
“3” until the signal beeps. If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.
■ Recalling the memorized position
Check that the shift lever is set in “P”.
Turn the “ENGINE START STOP ” switch to IGNITION ON
mode.
Press button “1”, “2” or “3” to
recall the desired position.STEP 1
STEP 2
STEP 3
STEP 1
STEP 2

841-3. Adjustable components (s eats, mirrors, steering wheel)
LX570_OM_OM60L21U_(U) Linking driving position memory with door unlock operation
Record your driving position to butto n “1”, “2” or “3” before performing
the following:
Using the wireless remote control
Turn the “ENGINE START STOP” switch to OFF after closing the
driver’s door.
While pressing the desired button
(“1”, “2” or “3”), press on
the wireless remote control until
the signal beeps. The driving position is recalled
when the driver’s door is unlocked
using the entry function or wireless
remote control and the driver’s
door is opened.
To prevent unintended triggering of the alarm, open and close a door once after
a driving position has been recorded. (If a door is not opened within 60 seconds
after is pressed, the doors will be locked again and the alarm will auto-
matically be set.)
In case that the alarm is triggere d, immediately stop the alarm. (  P. 1 1 9 )STEP 1
STEP 2

851-3. Adjustable components (s eats, mirrors, steering wheel)
1
Before driving
LX570_OM_OM60L21U_(U) Using the door lock switch
Carry only the key (including the ca rd key) to which you want to link
the driving position. If 2 or more keys are in the vehicle, the driving
position cannot be linked properly.
Turn the “ENGINE START STOP” switch to OFF after closing the
driver’s door.
While pressing the desired button
(“1”, “2” or “3”), press the lock or
unlock side on the door lock
switch (either the driver or passen-
ger side) until the signal beeps. The driving position is recalled
when the driver’s door is unlocked
using the enter function or wireless
remote control and the driver’s
door is opened.STEP 1
STEP 2
■
Canceling the linked do or unlock operation
Turn the “ENGINE START STOP” switch to OFF after closing the driver’s
door.
Using the wireless remote control: While pressing “SET” button, press
button on the wireless remote control until the signal beeps.
Using the door lock switch: While pressing “SET” button, press the lock or
unlock side on the door lock switch until the signal beeps.STEP 1
STEP 2

8711-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
LX570_OM_OM60L21U_(U) Head restraints Head restraints are provided for all seats.
Front seats
Vertical adjustment
Up
Down Push the head restraint up or
down while pressing the lock
release button.
Angle adjustment (if equipped)
Second seats
Vertical adjustment
Up Pull the head restraints up.
Down Push the head restraint down
while pressing the lock release
button.Lock release button
Lock release button

891-3. Adjustable components (s eats, mirrors, steering wheel)
1
Before driving
LX570_OM_OM60L21U_(U) ■
Removing the head restraints
Front seats
While pressing in the flathead screwdriver, pull up the head restraint.
Second seats
Third center seat
Third outboard seats
The head restraint cannot be removed.■
Installing the head restraints (except third outboard seats)
Align the head restraint with the installation holes.
Push down the head restra int to the lock position. Push a flathead screwdriver into the slot. The
slot is located on the right side of the right
head restraint anchor.STEP 1
STEP 2
Pull the head restraint up while pressing the
lock release button.
Lock release button
Pull the head restraint up while pressing the
lock release button.Lock
release
button
STEP 1
STEP 2