2014 Lexus IS250 ignition

1233-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Adjust the driver’s seat, steering wheel, and outside rear view mirrors to the
desired positions.
While pressing the “SET” button, or
within 3 seconds after the “SET” but-
ton is pressed, press button “1”, “2”
or “3” until a buzzer sounds.
If the selected button has already been
preset, the previously recorded position
will be overwritten.
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Press button “1”, “2” or “3” to recall
the desired position.
Driving position memory
: If equipped
Your preferred driving position (the position of the driver’s seat, steering
wheel and outside rear view mirrors) can be memorized and recalled by
pressing a button. It is also possible to set this function to activate automati-
cally when the doors are unlocked.
Three different driving positions can be entered into memory.
Entering a position to memory
1
2
3
4
Recalling the memorized position
1
2
3

1253-3. Adjusting the seats
3
Operation of each component
IS350/250_U (OM53758U)
A desired driving position can be recalled linked with the unlocking of the door.
■Setting procedure
Record your driving position to button “1”, “2” or “3” before performing the
following:
Carrying only the key (including the card key) to which you want to link the
driving position, shift the shift lever to P and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be linked prop-
erly.
Turn the engine switch to IGNITION ON mode and recall the position
which you want to link.
While pressing the button to
recall the position, press the
driver’s door lock switch (either
lock or unlock) until the buzzer
sounds.
The driving position is recalled when
the driver’s door is unlocked using
the entry function or wireless remote
control and the driver’s door is
opened.
■Cancelation procedure
Carry only the key for which you want to cancel the linked door unlock opera-
tion.
If 2 or more keys are in the vehicle, the driving position cannot be canceled
properly.
Turn the engine switch to IGNITION ON mode.
While pressing the “SET” button, press the driver’s door lock switch (either
lock or unlock) until the buzzer sounds.
Linking driving position memory with door unlock operation
1
2
1
2

1263-3. Adjusting the seats
IS350/250_U (OM53758U)
■When driving position memory is linked with door unlock operation
If the driver’s door is opened, the driver’s seat will move toward the memorized position
but stop slightly beforehand to allow easy access to the vehicle.
Turning the engine switch to ACCESSORY or IGNITION ON mode, or fastening the
driver’s seat belt moves the seat fully into the memorized position.
■Operating the driving position memory after turning the engine switch off
Memorized seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again. Memorized steering wheel posi-
tion can be activated by pr essing the engine switch.
■Correct seat position
When the seat is in the most forward or mo st backward position, and the seat is being
moved in those directions, the system may not correctly recognize the current position
and the memorized position will not be correctly recalled.
■The auto away function for exiting
If the seat is already close to the rearmost position, the auto away function may not oper-
ate when the driver exits the vehicle.
■When the driving position is recalled by a memory linked door unlock operation
●Since each memorized driving position is regi stered to a specific electronic key, the
driving position recalled may be different depending on the carried key.
●When only doors other than the driver’s d oor are unlocked by the smart access system
with push-button start, the driving position will not be recalled. In this case, press a driv-
ing position memory button to recall the desired driving position.
■Customization
The distance that the driver’s seat moves b ackward during the auto away function can be
changed. (Customizable features: P. 5 2 5 )
CAUTION
■Seat adjustment caution
Take care during seat adjustment so that th e seat does not strike the rear passenger or
squeeze your body against the steering wheel.

1313-4. Adjusting the steering wheel and mirrors
3
Operation of each component
IS350/250_U (OM53758U)
To sound the horn, press on or close to
the mark.
■The steering wheel can be adjusted when (power type)
The engine switch is in ACCESSORY or IGNITION ON mode
*.
*: If the driver’s seat belt is fastened, the steering wheel can be adjusted regardless of
engine switch mode.
■Automatic adjustment of the steering position (if equipped)
A desired steering position can be entered to memory and recalled automatically by the
driving position memory system. ( P. 1 2 3 )
■Power easy access system (if equipped)
The steering wheel and driver’s seat move in accordance with engine switch mode and
the driver’s seat belt condition. ( P. 1 2 4 )
Horn
CAUTION
■Caution while driving
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and cause an accident, result-
ing in death or serious injury.
■After adjusting the steering wheel (manual type)
Make sure that the steering wheel is securely locked.
Otherwise, the steering wheel may move suddenly, possibly causing an accident, and
resulting in death or serious injury. Also, the horn may not sound if the steering wheel is
not securely locked.

1323-4. Adjusting the steering wheel and mirrors
IS350/250_U (OM53758U)
The height of the rear view mirror can be adjusted to suit your driving posture.
Adjust the height of the rear view mir-
ror by moving it up and down.
Responding to the level of brightness of the headlights of vehicles behind, the
reflected light is automatically reduced.
Changing automatic anti-glare function mode
When the automatic anti-glare function is in ON mode, the indicator illuminates.
The function will set to ON mode each time the engine switch is turned to IGNITION
ON mode.
Pressing the button turns the function to OFF mode. (The indicator also turns off.)
Inside rear view mirror
The rear view mirror’s position can be adjusted to enable sufficient confirma-
tion of the rear view.
Adjusting the height of rear view mirror
Anti-glare function
Ty p e ATy p e B
ON
OFF ON/OFF
IndicatorIndicator
1
2

1353-4. Adjusting the steering wheel and mirrors
3
Operation of each component
IS350/250_U (OM53758U)
■Mirror angle can be adjusted when
The engine switch is in ACCESSORY or IGNITION ON mode.
■Linked mirror function when reversing (if equipped)
●When either “L” or “R” of the mirror select switch is selected, the outside rear view mir-
rors will automatically angle downwards when the vehicle is reversing in order to give a
better view of the ground. To disable this function, select neither “L” nor “R”.
●If the mirror angle adjustment switch is operated while the linked mirror function is in
operation, the angle and position of the mirrors can be remembered, and the mirrors
will operate at the angle adjusted to the la st time the linked mirror function was oper-
ated.
However, because the mirrors move based on the angle they are in when the linked
mirror function is not operating, the mirror angle when the linked mirror function is
operating will also be changed if the mirrors are adjusted while the function is not oper-
ating.
■When the mirrors are fogged up
The outside rear view mirrors can be cleare d using the mirror defoggers. Turn on the
rear window defogger to turn on the outside rear view mirror defoggers. ( P. 3 5 0 )
■Automatic adjustment of the mirror angle (if equipped)
A desired mirror face angle can be entered to memory and recalled automatically by the
driving position memory. ( P. 1 2 3 )
■Auto anti-glare function (if equipped)
When the anti-glare inside rear view mirror is set to automatic mode, the outside rear
view mirrors will activate in conjunction with the anti-glare inside rear view mirror to
reduce reflected light. ( P. 1 3 2 )

1383-5. Opening, closing the windows and moon roof
IS350/250_U (OM53758U)
■The power windows can be operated when
The engine switch is in IGNITION ON mode.
■Operating the power windows after turning the engine off
The power windows can be operated for approximately 45 seconds after the engine
switch is turned to ACCESSORY mode or turned off. They cannot, however, be oper-
ated once either front door is opened.
■Jam protection function
If an object becomes caught between the window and the window frame, window travel
is stopped and the window is opened slightly.
■When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot be closed,
perform the following operations using the po wer window switch on the relevant door.
●After stopping the vehicle, the window can be closed by holding the power window
switch in the one-touch closing position while the engine switch is turned to IGNITION
ON mode.
●If the window still cannot be closed even by carrying out the operation as explained
above, initialize the function by performing the following procedure.
Hold the power window switch in the one- touch closing position. Continue holding
the switch for a further 6 seconds after the window has closed.
Hold the power window switch in the one-touch opening position. Continue holding
the switch for a further 2 seconds after the window has opened completely.
Hold the power window switch in the one- touch closing position once again. Con-
tinue holding the switch for a further 2 seconds after the window has closed.
If you release the switch while the window is moving, start again from the beginning.
If the window continues to close but then re-open slightly even after performing the
above procedure correctly, have the ve hicle inspected by your Lexus dealer.
1
2
3

1413-5. Opening, closing the windows and moon roof
3
Operation of each component
IS350/250_U (OM53758U)
■The moon roof can be operated when
The engine switch is in IGNITION ON mode.
■Operating the moon roof after turning the engine off
The moon roof can be operated for approximately 45 seconds after the engine switch is
turned to ACCESSORY mode or turned off. It cannot, however, be operated once either
front door is opened.
■Jam protection function
If an object is detected between the moon roof and the frame while the moon roof is clos-
ing or tilting down, travel is stoppe d and the moon roof opens slightly.
■Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open
automatically when the moon roof is opened.
■Door lock linked moon roof operation
●The moon roof can be opened and closed using the mechanical key.* ( P. 4 8 8 )
●The moon roof can be opened us ing the wireless remote control.* ( P. 1 0 3 )
*: These settings must be customized at your Lexus dealer.