2014 Lancia Voyager diagram

child restraint. Repeat steps 4 to 6,
above, to complete the installation of
the child restraint.
If the belt still cannot be tightened
after you shorten the buckle, discon-
nect the latch plate from the buckle,
turn the buckle around one half turn,
and insert the latch plate into the
buckle again. If you still cannot make
the child restraint installation tight,
try a different seating position.
Installing Child Restraints Using
The Top Tether Anchorage
1. Look behind the seating position
where you plan to install the child
restraint to find the tether anchorage.
You may need to move the seat for-
ward to provide better access to the
tether anchorage. If there is no top
tether anchorage for that seating po-
sition, move the child restraint to an-
other position in the vehicle if one is
available.2. Route the tether strap to provide
the most direct path for the strap be-
tween the anchor and the child seat. If
your vehicle is equipped with adjust-
able rear head restraints, raise the
head restraint, and where possible,
route the tether strap under the head
restraint and between the two posts. If
not possible, lower the head restraint
and pass the tether strap around the
outboard side of the head restraint.
3. Attach the tether strap hook of the
child restraint to the top tether an-
chorage as shown in the diagram.
4. Remove slack in the tether strap
according to the child restraint manu-
facturer’s instructions.
WARNING!
An incorrectly anchored tether
strap could lead to increased head
motion and possible injury to the
child. Use only the anchorage po-
sition directly behind the child
seat to secure a child restraint top
tether strap.
If your vehicle is equipped with a split rear seat, make sure the
tether strap does not slip into the
opening between the seatbacks as
you remove slack in the strap.
Rear Seat Tether Strap Mounting
(Second Row Anchorage Shown)
ISOFIX Anchorages (Third Row 60/40 Anchorage Shown)
67

REPLACING THE REMOTE
CONTROL BATTERIES
The remote control requires two AAA
batteries for operation. To replace the
batteries:
Locate the battery compartment onthe back of the remote, then slide
the battery cover downward.
Replace the batteries, making sure to orient them according to the po-
larity diagram shown.
Replace the battery compartment cover.
HEADPHONES OPERATION
The headphones receive two separate
channels of audio using an infrared
transmitter from the video screen.
Front seat occupants receive some
headphone audio coverage to allow
them to adjust the headphone volume
for the young rear seat occupants that
may not be able to do so for them-
selves. If no audio is heard after increasing
the volume control, verify that the
screen is turned on and in the down
position and that the channel is not
muted and the headphone channel se-
lector switch is on the desired chan-
nel. If audio is still not heard, check
that fully charged batteries are in-
stalled in the headphones.
Blu-ray HEADPHONES
OPERATION
The headphones receive two separate
channels of audio using an infrared
transmitter from the video screen.Front seat occupants receive some
headphone audio coverage to allow
them to adjust the headphone volume
for the young rear seat occupants that
may not be able to do so for them-
selves.
If no audio is heard after increasing
the volume control, verify that the
screen is turned on and in the down
position and that the channel is not
muted and the headphone channel se-
lector switch is on the desired chan-
nel. If audio is still not heard, check
that fully charged batteries are in-
stalled in the headphones.
1. Volume Control
2. Power Button
3. Channel Selection Switch
4. Power Indicator
1. Power Button
2. Volume Control
3. Channel Selection Switch
206

CONTROLS
The headphone power indicator and
controls are located on the right ear
cup.
NOTE: The rear video system
must be turned on before sound
can be heard from the head-
phones. To conserve battery life,
the headphones will automatically
turn off approximately three min-
utes after the rear video system is
turned off.
Changing the Audio Mode for
Headphones
1. Ensure the Remote Control
channel/screen selector switch is in
the same position as the headphone
selector switch.
NOTE:
When both switches are onChannel 1, the Remote is con-
trolling Channel 1 and the head-
phones are tuned to the audio of
the VES™ Channel 1. When both switches are on
Channel 2, the Remote is con-
trolling Channel 2 and the head-
phones are tuned to the audio of
the VES™ Channel 2.
2. Press the MODE button on the re-
mote control.
3. If the video screen is displaying a
video source (such as a DVD Video),
pressing STATUS shows the status on
a popup banner at the bottom of the
screen. Pressing the MODE button
will advance to the next mode. When
the mode is in an audio only source
(such as FM), the Mode Selection
menu appears on screen.
4. When the Mode Selection menu
appears on screen, use the cursor but-
tons on the remote control to navigate
to the available modes and press the
ENTER button to select the new
mode.
5. To cancel out of the Mode Selec-
tion menu, press the BACK button on
the remote control.
REPLACING THE
HEADPHONE BATTERIES
Each set of headphones requires two
AAA batteries for operation. To re-
place the batteries:
Locate the battery compartment on the left ear cup of the headphones,
and then slide the battery cover
downward.
Replace the batteries, making sure to orient them according to the po-
larity diagram shown.
Replace the battery compartment cover.
UNWIRED® STEREO
HEADPHONE LIFETIME
LIMITED WARRANTY
Who Does This Warranty Cover?
This warranty covers the initial user
or purchaser ("you" or "your") of this
particular Unwired Technology LLC
("Unwired") wireless headphone
("Product"). The warranty is not
transferable.
207