desired. Once the brake pedal is re-
leased, the BAS is deactivated.
WARNING!
The BAS cannot prevent the natu-
ral laws of physics from acting on
the vehicle, nor can it increase the
traction afforded by prevailing
road conditions. The BAS cannot
prevent collisions, including those
resulting from excessive speed in
turns, driving on very slippery sur-
faces, or hydroplaning. The capa-
bilities of a BAS-equipped vehicle
must never be exploited in a reck-
less or dangerous manner that
could jeopardize the user's safety or
the safety of others.
ELECTRONIC STABILITY
CONTROL (ESC)
This system enhances directional con-
trol and stability of the vehicle under
various driving conditions. The ESC
corrects for oversteering and under-
steering the vehicle by applying the
brake of the appropriate wheel. En-
gine power may also be reduced to
assist in counteracting the condition
of oversteer or understeer and help
the vehicle maintain the desired path.
The ESC uses sensors in the vehicle to
determine the path that the driver
intends to steer the vehicle and com-
pares it to the actual path of the ve-
hicle. When the actual path does not
match the intended path, the ESC
applies the brake of the appropriate
wheel to assist in counteracting the
condition of oversteer or understeer.
Oversteer - when the vehicle isturning more than appropriate for
the steering wheel position.
Understeer - when the vehicle is turning less than appropriate for
the steering wheel position.
WARNING!
The Electronic Stability Control
(ESC) cannot prevent the natural
laws of physics from acting on the
vehicle, nor can it increase the trac-
tion afforded by prevailing road
conditions. ESC cannot prevent all
accidents, including those resulting
from excessive speed in turns, driv-
ing on very slippery surfaces, or
hydroplaning. ESC also cannot
prevent collisions resulting from
loss of vehicle control due to inap-
propriate driver input for the con-
ditions. Only a safe, attentive, and
skillful driver can prevent acci-
dents. The capabilities of an ESC
equipped vehicle must never be ex-
ploited in a reckless or dangerous
manner which could jeopardize the
user’s safety or the safety of others.
ESC Operating Modes
The ESC system has two or three
available operating modes:
ESC On
This is the normal operating mode for
the ESC. Whenever the vehicle is
220
started, the ESC system will be in this
mode. This mode should be used for
most driving conditions. The ESC
should only be turned OFF for spe-
cific reasons as noted in the following
paragraphs.
Partial Off
The “Partial Off” mode is intended
for times when a more spirited driving
experience is desired. It is also in-
tended for driving in deep snow, sand,
or gravel. This mode disables the TCS
portion of the ESC and raises the
threshold for ESC activation, which
allows for more wheel spin than what
ESC normally allows.
The “ESC Off” switch is located on
the switch bank in the center of the
instrument panel. To enter the “Par-
tial Off” mode, momentarily press the
“ESC Off” switch and the “ESC off
indicator light” will illuminate. To
turn the ESC on again, momentarily
press the “ESC Off” switch and the
“ESC off indicator light” will turn off.WARNING!
When in “Partial Off” mode, theTCS functionality of ESC, (ex-
cept for the limited slip feature
described in the TCS section), has
been disabled and the “ESC Off
Indicator Light” will be illumi-
nated. When in “Partial Off”
mode, the engine power reduction
feature of TCS is disabled, and
the enhanced vehicle stability of-
fered by the ESC system is re-
duced
Trailer Sway control (TSC) is dis- abled when the ESC system is in
the “Partial Off” mode.
NOTE:
To improve the vehicle's traction when driving with snow chains,
or when starting off in deep
snow, sand, or gravel, it may be
desirable to switch to the “Par-
tial Off” mode by momentarily
pressing the “ESC Off” switch.
Once the situation requiring
“Partial Off” mode is overcome, turn the ESC on again by mo-
mentarily pressing the “ESC Off”
switch. This may be done while
the vehicle is in motion.
Trailer Sway control (TSC) is disabled when the ESC system is
in the “Partial Off” mode.
Full Off (for versions/markets,
where provided)
This mode is intended for off-
highway or off-road use only and
should not be used on any public
roadways.
In this mode, all TCS and ESC stabil-
ity features are turned OFF. To enter
the “Full Off” mode, press and hold
the “ESC Off” switch for five seconds
while the vehicle is stopped with the
engine running. After five seconds, a
chime will sound, the “ESC Off Indi-
cator Light” will illuminate, and the
“ESC OFF” message will display in
the Electronic Vehicle Information
Center (EVIC). To turn ESC ON
again, momentarily press the “ESC
Off” switch.
221
driven several kilometers at speeds
greater than 48 km/h, see your autho-
rized dealer as soon as possible to
have the problem diagnosed and
corrected.
The “ESC Activation/Malfunction In-
dicator Light” (located in the instru-
ment cluster) starts to flash as soon as
the tires lose traction and the ESC
system becomes active. The “ESC
Activation/Malfunction Indicator
Light” also flashes when TCS is ac-
tive. If the “ESC Activation/
Malfunction Indicator Light” begins
to flash during acceleration, ease up
on the accelerator and apply as little
throttle as possible. Be sure to adapt
your speed and driving to the prevail-
ing road conditions.
NOTE:
The “ESC Activation/Malfunction Indicator Light”
and the “ESC OFF Indicator
Light” come on momentarily
each time the ignition switch is
turned ON. Each time the ignition is turned
ON, the ESC system will be ON
even if it was turned off
previously.
The ESC system will make buzz- ing or clicking sounds when it is
active. This is normal; the
sounds will stop when ESC be-
comes inactive following the
maneuver that caused the ESC
activation.
The “ESC OFF Indicator
Light” indicates the Elec-
tronic Stability Control
(ESC) is in Partial OFF
mode.
SYNCHRONIZING ESC
If the power supply is inter-
rupted (battery disconnected
or discharged), the “ESC
Activation/Malfunction In-
dicator Light” may illuminate with the
engine running. If this should occur,
turn the steering wheel completely to
the left and then to the right. The “ESC
Activation/Malfunction Indicator Light” should go out. However, if the
light remains on, have the ESC and
BAS checked at your authorized dealer
as soon as possible.
TIRES — GENERAL
INFORMATION
Tire Pressure
Proper tire inflation pressure is essen-
tial to the safe and satisfactory opera-
tion of your vehicle. Three primary
areas are affected by improper tire
pressure:
Safety
WARNING!
Improperly inflated tires are dan-
gerous and can cause collisions.
Under-inflation increases tire flexing and can result in over-
heating and tire failure.
(Continued)
224
It is not recommended driving a ve-
hicle loaded at full capacity or to tow
a trailer while a tire is in the run flat
mode.
See the tire pressure monitoring sec-
tion for more information.
Spare Tires (for
versions/markets, where
provided)
NOTE: For vehicles equipped
with TIREFIT instead of a spare
tire, please refer to “TIREFIT KIT”
in “In an emergency” for further
information.
CAUTION!
Because of the reduced ground
clearance, do not take your vehicle
through an automatic car wash
with a compact, full size or limited-
use temporary spare installed.
Damage to the vehicle may result.Spare Tire Matching Original
Equipped Tire And Wheel (for
versions/markets, where
provided)
Your vehicle may be equipped with a
spare tire and wheel equivalent in
look and function to the original
equipment tire and wheel found on
the front or rear axle of your vehicle.
This spare tire may be used in the tire
rotation for your vehicle. If your ve-
hicle has this option, refer to an au-
thorized tire dealer for the recom-
mended tire rotation pattern.
Compact Spare Tire (for
versions/markets, where
provided)The compact spare is for temporary
emergency use only. You can identify if
your vehicle is equipped with a com-
pact spare by looking at the spare tire
description on the Tire and Loading
Information Placard located on the
driver’s side door opening or on the
sidewall of the tire. Compact spare tire
descriptions begin with the letter “T”
or “S” preceding the size designation.
Example: T145/80D18 103M.
T, S = Temporary Spare Tire
Since this tire has limited tread life,
the original equipment tire should be
repaired (or replaced) and reinstalled
on your vehicle at the first opportu-
nity.
Do not install a wheel cover or at-
tempt to mount a conventional tire on
the compact spare wheel, since the
wheel is designed specifically for the
compact spare tire. Do not install
more than one compact spare tire and
wheel on the vehicle at any given time.
WARNING!
Compact spares are for temporary
emergency use only. With these
spares, do not drive more than
80 km/h. Temporary use spares
have limited tread life. When the
tread is worn to the tread wear in-
dicators, the temporary use spare
tire needs to be replaced. Be sure to
follow the warnings, which apply to
your spare. Failure to do so could
result in spare tire failure and loss
of vehicle control.
228
Full Size Spare (for
versions/markets, where
provided)
The full size spare is for temporary
emergency use only. This tire may
look like the originally equipped tire
on the front or rear axle of your ve-
hicle, but it is not. This spare tire may
have limited tread life. When the
tread is worn to the tread wear indi-
cators, the temporary use full size
spare tire needs to be replaced. Since
it is not the same as your original
equipment tire, replace (or repair) the
original equipment tire and reinstall
on the vehicle at the first opportunity.
Limited-Use Spare (for
versions/markets, where
provided)
The limited-use spare tire is for tem-
porary emergency use only. This tire is
identified by a label located on the
limited-use spare wheel. This label
contains the driving limitations for
this spare. This tire may look like the
original equipped tire on the front or
rear axle of your vehicle, but it is not.
Installation of this limited-use sparetire affects vehicle handling. Since it is
not the same as your original equip-
ment tire, replace (or repair) the origi-
nal equipment tire and reinstall on the
vehicle at the first opportunity.
WARNING!
Limited-use spares are for emer-
gency use only. Installation of this
limited-use spare tire affects ve-
hicle handling. With this tire, do
not drive more than the speed listed
on the limit-use spare wheel. Keep
inflated to the cold tire inflation
pressures listed on your Tire and
Loading Information Placard lo-
cated on the driver’s side B-Pillar or
the rear edge of the driver’s side
door. Replace (or repair) the origi-
nal equipment tire at the first op-
portunity and reinstall it on your
vehicle. Failure to do so could result
in loss of vehicle control.
Tire Spinning
When stuck in mud, sand, snow, or ice
conditions, do not spin your vehicle's
wheels above 48 km/h or for longer
than 30 seconds continuously without
stopping.
Refer to “Freeing A Stuck Vehicle” in
“In an emergency” for further infor-
mation.
WARNING!
Fast spinning tires can be danger-
ous. Forces generated by excessive
wheel speeds may cause tire dam-
age or failure. A tire could explode
and injure someone. Do not spin
your vehicle's wheels faster than
48 km/h for more than 30 seconds
continuously when you are stuck,
and do not let anyone near a spin-
ning wheel, no matter what the
speed.
229
Tread Wear Indicators
Tread wear indicators are in the origi-
nal equipment tires to help you in
determining when your tires should
be replaced.
These indicators are molded into the
bottom of the tread grooves. They will
appear as bands when the tread depth
becomes 2 mm. When the tread is
worn to the tread wear indicators, the
tire should be replaced. Refer to “Re-
placement Tires” in this section for
further information.
Life Of Tire
The service life of a tire is dependent
upon varying factors including, but
not limited to:
Driving style
Tire pressure
Distance driven
Performance tires, tires with aspeed rating of V or higher, and
summer tires typically have a re-
duced tread life. Rotation of these
tires per the vehicle maintenance
schedule is highly recommended.
WARNING!
Tires and the spare tire should be
replaced after six years, regardless
of the remaining tread. Failure to
follow this warning can result in
sudden tire failure. You could lose
control and have a collision result-
ing in serious injury or death.
Keep dismounted tires in a cool, dry
place with as little exposure to light as
possible. Protect tires from contact
with oil, grease, and gasoline.
Replacement Tires
The tires on your new vehicle provide
a balance of many characteristics.
They should be inspected regularly
for wear and correct cold tire inflation
pressure. The manufacturer strongly
recommends that you use tires
equivalent to the originals in size,
quality and performance when re-
placement is needed. Refer to the
paragraph on “Tread Wear Indica-
tors”. Refer to the Tire and Loading
Information placard or the Vehicle
Certification Label for the size desig-
nation of your tire. The Load Index
and Speed Symbol for your tire will be
found on the original equipment tire
sidewall. See the Tire Sizing Chart
example found in the Tire Safety In-
formation section of this manual for
more information relating to the Load
Index and Speed Symbol of a tire.
It is recommended to replace the two
front tires or two rear tires as a pair.
Replacing just one tire can seriously
affect your vehicle’s handling. If you
ever replace a wheel, make sure that
the wheel’s specifications match those
of the original wheels.
1 — Worn Tire
2—NewTire
230
It is recommended you contact your
authorized tire dealer or original
equipment dealer with any questions
you may have on tire specifications or
capability. Failure to use equivalent
replacement tires may adversely af-
fect the safety, handling, and ride of
your vehicle.
WARNING!
Do not use a tire, wheel size orrating other than that specified
for your vehicle. Some combina-
tions of unapproved tires and
wheels may change suspension
dimensions and performance
characteristics, resulting in
changes to steering, handling,
and braking of your vehicle. This
can cause unpredictable handling
and stress to steering and suspen-
sion components. You could lose
control and have a collision re-
sulting in serious injury or death.
Use only the tire and wheel sizes
with load ratings approved for
your vehicle.
(Continued)
WARNING!(Continued)
Never use a tire with a smallerload index or capacity, other than
what was originally equipped on
your vehicle. Using a tire with a
smaller load index could result in
tire overloading and failure. You
could lose control and have a col-
lision.
Failure to equip your vehicle with
tires having adequate speed capa-
bility can result in sudden tire fail-
ure and loss of vehicle control.
CAUTION!
Replacing original tires with tires of
a different size may result in false
speedometer and odometer read-
ings.
TIRE CHAINS
(TRACTION DEVICES)
Use of traction devices require suffi-
cient tire-to-body clearance. Follow
these recommendations to guard
against damage.
Traction device must be of proper size for the tire, as recommended by
the traction device manufacturer.
Install on Rear Tires Only.
Due to limited clearance, on a 235/ 55R18 100V, use reduced size snow
chains or traction devices with a
maximum projection of 6 mm be-
yond the tire profile.
WARNING!
Using tires of different size and type
(M+S, Snow) between front and
rear axles can cause unpredictable
handling. You could lose control
and have a collision.
231
General Information” in “Starting
and Operating” for information on
how to properly inflate the vehicle’s
tires. The tire pressure will also in-
crease as the vehicle is driven - this is
normal and there should be no adjust-
ment for this increased pressure.
The TPMS will warn the driver of a
low tire pressure if the tire pressure
falls below the low-pressure warning
limit for any reason, including low
temperature effects and natural pres-
sure loss through the tire.
The TPMS will continue to warn the
driver of low tire pressure as long as
the condition exists, and will not turn
off until the tire pressure is at or above
the recommended cold placard pres-
sure. Once the low tire pressure warn-
ing (Tire Pressure Monitoring [TPM]
Telltale Light) illuminates, you must
increase the tire pressure to the rec-
ommended cold placard pressure in
order for the TPM Telltale Light to
turn off. The system will automati-
cally update and the TPM Telltale
Light will turn off once the system
receives the updated tire pressures.The vehicle may need to be driven for
up to 20 minutes above 24 km/h in
order for the TPMS to receive this
information.
For example, your vehicle may have a
recommended cold (parked for more
than three hours) placard pressure of
2.1 BAR. If the ambient temperature
is 20°C and the measured tire pres-
sure is 1.9 BAR, a temperature drop to
-7°C will decrease the tire pressure to
approximately 1.6 BAR. This tire
pressure is sufficiently low enough to
turn ON the TPM Telltale Light. Driv-
ing the vehicle may cause the tire
pressure to rise to approximately 1.9
BAR, but the TPM Telltale Light will
still be ON. In this situation, the TPM
Telltale Light will turn OFF only after
the tires are inflated to the vehicle’s
recommended cold placard pressure
value.CAUTION!
The TPMS has been optimized
for the original equipment tires
and wheels. TPMS pressures have
been established for the tire size
equipped on your vehicle. Unde-
sirable system operation or sensor
damage may result when using
replacement equipment that is
not of the same size, type, and/or
style. Aftermarket wheels can
cause sensor damage. It is recom-
mended not to use aftermarket
sealants or balance beads if your
vehicle is equipped with a TPMS,
as damage to the sensors may re-
sult. In case of use of aftermarket
tire sealants not equivalent to the
original TIREFIT sealant, please
take your vehicle to a authorized
dealer to have the sensor function
checked.
After inspecting or adjusting the tire pressure always reinstall the
valve stem cap. This will prevent
moisture and dirt from entering
the valve stem, which could dam-
age the TPMS sensor.
233