2014 JEEP RENEGADE headlight bulb

❒Position 3: driver + maximum
permitted load stowed only in the
luggage compartment
IMPORTANT Check the headlight
alignment each time the weight of the
load transported changes.
INSTRUMENT PANEL AND
CONTROL BUTTON
GRAPHICS BRIGHTNESS
ADJUSTMENT
With side lights or headlights on, turn
ring nut B fig. 27 upwards to increase
light brightness of the instrument panel
and of the control button graphics, or
turn the ring nut downwards to
decrease it.
WARNING
18)The daytime running lights are an
alternative to the dipped beam headlights
for driving in countries where it is
compulsory to have lights on during the
day; where it is not compulsory, the use of
daytime running lights is permitted.
19)Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels. The use of
daytime running lights is governed by the
highway code of the country in which
you are driving. Comply with legal
requirements.
INTERIOR LIGHTS
FRONT COURTESY
LIGHTS
Switch A fig. 28 is used to switch on/off
the courtesy lights bulbs.
Switch positions:
❒central position: lights C and E switch
on/off when the doors are opened/
closed;
❒pressed to the left (position OFF):
lights C and E are always switched off;
❒pressed to the right (position
):
lights C and D are always switched on.
The lights switch on/off gradually.
Switch B fig. 28 switches light C on/off.
Switch D fig. 28 switches light E on/off.
27J0A0064C
21

HAZARD WARNING
LIGHTS
CONTROL
Press button fig. 105 to switch the
lights on/off.
When the hazard warning lights are on,
the
andwarning lights flash.
IMPORTANT The use of hazard warning
lights is governed by the highway
code of the country you are driving in:
comply with legal requirements.
Emergency braking
In the event of an emergency braking
the hazard warning lights switch on
automatically as well as warning lights
andin the instrument panel.
The lights switch off automatically when
emergency braking ceases.
REPLACING A BULB
133) 134) 135)52)
GENERAL
INSTRUCTIONS
❒Before replacing a bulb check the
contacts for oxidation;
❒replace blown bulbs with others of
the same type and power;
❒after replacing a headlight bulb,
always check its alignment;
❒when a light is not working, check
that the corresponding fuse is intact
before replacing the bulb. For the
location of fuses, refer to the paragraph
“If a fuse blows” in this chapter.IMPORTANT When the weather is cold
or damp or after heavy rain or washing,
the surface of headlights or rear lights
may steam up and/or form drops of
condensation on the inside. This is
a natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside
of the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from
the centre of the diffuser, extending
progressively towards the edges.
105J0A0050C
124
IN AN EMERGENCY

BulbsType Power
Front side lights/Daytime running lights (DRL) P21/5W 21/5 W
Rear side lightsP21W 21 W
Main beam/dipped beam headlights (halogen) H4 60/55 W
Main beam/dipped beam headlights (Xenon gas discharge) D5S 25 W
Front direction indicatorsPY21W 21 W
Rear direction indicatorsW16W 16 W
Side direction indicators (front and on door mirror) WY5W 5 W
3rd brake lightLED –
Number plateW5W 5 W
Fog lightsH11 55 W
Rear fog lightW16W 16 W
Reverse lightW16W 16 W
Front courtesy lightsC5W 5 W
Front roof lights (sun visors)C5W 5 W
Rear roof light (versions without sun roof) C5W 5 W
Rear roof lights (versions with sun roof) C5W 5 W
Luggage compartment roof lights W5W 5 W
Glove compartment lightW5W 4 W
125

CHANGING AN EXTERIOR
LIGHT
Front upper light cluster
(main beam/dipped halogen
headlights)
To replace the bulb, proceed as follows:
❒working from inside the engine
compartment, remove cover A fig. 106,
using the dedicated tab;
❒turn the bulb and bulb holder
assembly B fig. 107 anticlockwise and
then remove it outwards;❒remove, outwards, the bulb and bulb
holder assembly C fig. 108,
disconnecting it from connector D;
❒install the new bulb and bulb holder
assembly, ensuring that it is locked
correctly;
❒then insert the bulb and bulb holder
unit in its housing and turn it clockwise,
making sure that it is locked correctly.
IMPORTANT Only replace the bulb
when the engine is off. Also ensure that
the engine is cold, to prevent the risk
of burns.
Front upper light cluster
(main beam/dipped Xenon
gas discharge headlights)
For replacing these bulbs, contact
a Jeep Dealership.
Front lower light cluster
Side light/daytime running lights (DRLs)
and front direction indicators
To replace the bulbs proceed as
follows:
❒steer the wheels completely;
❒using the screwdriver, undo screws A
fig. 109 and remove flap B;
❒remove electrical connectors C fig.
110;
106J0A0260C
107J0A0261C
108J0A0414C
109J0A0211C
110J0A0306C
126
IN AN EMERGENCY