2014 INFINITI Q70 engine oil

Black plate (446,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-8Maintenance and do-it-yourself
SDI2538
1. Battery
2. Fuse/fusible link holder
3. Engine oil filler cap
4. Brake fluid reservoir
5. Window washer fluid reservoir
6. Power steering fluid reservoir
7. Air cleaner
8. Radiator filler cap
9. Engine coolant reservoir
10. Engine oil dipstick
11. Drive belts
12. Fuse/fusible link holder
Condition:

Black plate (448,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-10Maintenance and do-it-yourself
JVC0538X
Type AGUID-5752B3A4-D8FF-4961-9160-5090555FCE311. Fuse/fusible link holder
2. Battery
3. Engine oil filler cap
4. Brake fluid reservoir
5. Window washer fluid reservoir
6. Power steering fluid reservoir
7. Air cleaner
8. Radiator filler cap
9. Engine coolant reservoir
10. Engine oil dipstick
11. Drive belts
Condition:

Black plate (449,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
JVC0539X
Type BGUID-CA2406D1-CA97-4C99-9B20-6F21F956C6CA1. Fuse/fusible link holder
2. Battery
3. Engine oil filler cap
4. Brake fluid reservoir
5. Window washer fluid reservoir
6. Power steering fluid reservoir
7. Air cleaner
8. Radiator filler cap
9. Engine coolant reservoir
10. Engine oil dipstick
11. Drive belts
Maintenance and do-it-yourself8-11
Condition:

Black plate (452,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-14Maintenance and do-it-yourself
engine. Run the engine until it reaches
normal operating temperature. Add coolant
up to the MAX level
*1. Tighten the cap
securely after adding engine coolant.
If the cooling system requires coolant
frequently, have it checked by an INFINITI
retailer.
CHANGING ENGINE COOLANTY51D-V-E01-A426F257-7E1C-4FDD-BCE7-CC70502D59EAMajor cooling system repairs should be
performed by an INFINITI retailer. The
service procedures can be found in the
appropriate INFINITI Service Manual.
Improper servicing can result in reduced
heater performance and engine overheat-
ing.
WARNING
. To avoid the danger of being scalded,
never change the coolant when the
engine is hot.
. Never remove the radiator cap when the
engine is hot. Serious burns could be
caused by high pressure fluid escaping
from the radiator.
. Avoid direct skin contact with used
coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
. Keep coolant out of reach of children and
pets.
Engine coolant must be disposed of
properly. Check your local regulations.
Y51D-V-E01-A7C453B1-918A-4063-9B01-B06D637810DF
SDI2541
VK56VD engine
SDI2045
VQ37VHR engine
ENGINE OIL
Condition:

Black plate (453,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
CHECKING ENGINE OIL LEVELY51D-V-E01-F1375A53-9C95-4044-9249-810C01D32BB11. Park the vehicle on a level surface andapply the parking brake.
2. Run the engine until it reaches operat- ing temperature.
3. Turn off the engine. Wait more than 15
minutes for the oil to drain back into
the oil pan.
4. Remove the dipstick and wipe it clean. Reinsert it all the way.
5. Remove the dipstick again and check the oil level. It should be within the
range
*1. If the oil level is below*2,
remove the oil filler cap and pour
recommended oil through the opening.
Do not overfill
*3.
6. Recheck oil level with the dipstick.
It is normal to add some oil between oil
maintenance intervals or during the break-
in period, depending on the severity of
operating conditions.
CAUTION
Oil level should be checked regularly.
Operating the engine with an insufficient
amount of oil can damage the engine, and such damage is not covered by warranty.
CHANGING ENGINE OIL AND FILTERY51D-V-E01-9647A2B0-4907-4EB7-83BB-101487A3007A
Vehicle set-upY51D-V-E01-A77DD255-330F-4511-9453-9FE2A63539431. Park the vehicle on a level surface and
apply the parking brake.
2. Run the engine until it reaches operat- ing temperature.
3. Turn the engine off and wait more than 15 minutes.
4. Raise and support the vehicle using a suitable floor jack and safety jack
stands.
.Place the safety jack stands under
the vehicle jack-up points.
.A suitable adapter should be at-tached to the jack stand saddle.
5. Remove the plastic engine undercover.
.Remove the small plastic clip at the center point of the undercover.
.Then remove the other bolts thathold the undercover in place.
CAUTION
Make sure the correct lifting and support
points are used to avoid vehicle damage.
Maintenance and do-it-yourself8-15
Condition:

Black plate (454,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
8-16Maintenance and do-it-yourself
SDI2543
VK56VD engine—2WD models
SDI2335
VQ37VHR engine —2WD models
SDI2320
VK56VD engine —AWD models
SDI2047
VQ37VHR engine —AWD models
Engine oil and filterY51D-V-E01-E1C6F53B-E6EA-4EFF-A78E-74F5B4A219BD1. Place a large drain pan under the drain
plug.
2. Remove the oil filler cap.
3. Remove the drain plug
*1with a
wrench and completely drain the oil.
CAUTION
Be careful not to burn yourself, as the
engine oil is hot.
.Waste oil must be disposed of
properly.
.Check your local regulations.
4. (Perform steps 4 to 7 only when the engine oil filter change is needed.)
Loosen the oil filter
*2with an oil filter
wrench. Remove the oil filter by turning
it by hand.
5. Wipe the engine oil filter mounting
surface with a clean rag.
CAUTION
Be sure to remove any old rubber gasket
remaining on the mounting surface of the
Condition:

Black plate (455,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
engine. Failure to do so could lead to engine
damage.
6. Coat the gasket on the new filter withclean engine oil.
7. Screw in the oil filter clockwise until a slight resistance is felt, then tighten
additionally more than 2/3 turn.
Oil filter tightening torque:11 to 15 ft-lb
(14.7 to 20.5 N·m)
8. Clean and re-install the drain plug with a new washer. Securely tighten the
drain plug with a wrench.
Drain plug tightening torque:22 to 29 ft-lb
(29 to 39 N·m)
Do not use excessive force.
9. Refill engine with recommended oil and install the oil filler cap securely.
CAUTION
The dipstick must be inserted in place to
prevent oil spillage from the dipstick hole
while filling the engine with oil.
See “Capacities and recommended fuel/lubricants”
(P.9-2) for drain and
refill capacity. The drain and refill
capacity depends on the oil tempera-
ture and drain time. Use these specifi-
cations for reference only. Always use
the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than 15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operationY51D-V-E01-790CC92C-2688-443C-80B6-74DD163C016F1.Install the engine undercover into
position as the following steps.
a. Pull the center of the small plastic
clip out.
b. Hold the engine undercover into position.
c. Insert the clip through the under- cover into the hole in the frame, then
push the center of the clip in to lock
the clip in place.
d. Install the other bolts that hold the undercover in place. Be careful not
to strip the bolts or over-tighten them.
2. Lower the vehicle carefully to the
ground.
3. Dispose of waste oil and filter properly.
WARNING
. Prolonged and repeated contact with
used engine oil may cause skin cancer.
. Try to avoid direct skin contact with used
oil. If skin contact is made, wash
thoroughly with soap or hand cleaner
as soon as possible.
. Keep used engine oil out of reach of
children.
Maintenance and do-it-yourself8-17
Condition:

Black plate (487,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
9 Technical and consumer information
Capacities and recommended fuel/lubricants...
....... 9-2
Fuel information ...
.............................................. 9-4
Engine oil and oil filter recommendation ...
......... 9-6
Air conditioning system refrigerant and
lubricant recommendations ...
............................. 9-7
Specifications ...
...................................................... 9-8
Engine ...
............................................................. 9-8
Wheels and tires ...
............................................. 9-9
Dimensions ...
................................................... 9-10
When traveling or registering your vehicle in
another country ...
................................................. 9-11
Vehicle identification ...
......................................... 9-11
Vehicle Identification Number (VIN) plate ...
....... 9-11
Vehicle identification number
(chassis number) ...
........................................... 9-11
Engine serial number ...
.................................... 9-12
F.M.V.S.S./C.M.V.S.S. certification label ...
.......... 9-12
Emission control information label ...
................ 9-13
Tire and loading information label ...
................. 9-13
Air conditioner specification label ...
.................. 9-13 Installing front license plate
...
.............................. 9-14
Vehicle loading information ...
............................... 9-15
Terms ...
.......................................................... 9-15
Vehicle load capacity ...
................................... 9-17
Loading tips ...
................................................. 9-18
Measurement of weights ...
.............................. 9-18
Towing a trailer ...
................................................. 9-19
Flat towing ...
................................................... 9-19
Uniform tire quality grading ...
.............................. 9-19
Treadwear ...
.................................................... 9-19
Traction AA, A, B and C ...
................................ 9-20
Temperature A, B and C ...
............................... 9-20
Emission control system warranty ...
..................... 9-20
Reporting safety defects ...
.................................... 9-21
Readiness for Inspection/Maintenance (I/M) test
(US only) ...
........................................................... 9-22
Event Data Recorders (EDR) ...
............................... 9-23
Owner’s Manual/Service Manual
order information ...
.............................................. 9-23
Condition: