2014 HYUNDAI I20 clock

1.#$
,204/3424-3
FFuse Name
Symbol
Fuse rating
Circuit Protected
SAFETY P/WDW
25A
Driver Safety Power Window Module
P/WDW LH
25A
Power Window Main Switch, Passenger Power Window Switch (RHD)
HTD MIRR
10A
PCM/ECM, A/C Control Module, Driver/Passenger Power Outside Mirror
FOG LP FRT
10A
Front Fog Lamp Relay
RR HTD
30A
RR HTD Relay
P/WDW RH
25A
Driver Power Window Switch
STOP LAMP
STOP
LAMP
15A
Stop Signal Electronic Module
POWER OUTLET LH
20A
Power Outlet LH & USB Charger
DR LOCK
20A
T/Gate Unlock Relay, Door Lock/Unlock Relay
A/CON 2
10A
A/CON Fuse for Clutch+Condition
POWER OUTLET RH
20A
Power Outlet RH
BLOWER
10A
A/C Control Module, Blower Motor
ACC
10A
Power Outside Mirror Switch, Auido, Digital Clock, BCM, Smart Key Control Module,
I/P Junction Block (P/OUTLET Relay)
START
10A
CVT : Transaxle Range Switch,
M/T : PCM/ECM, E/R Junction Block (Start Relay), Ignition Lock Switch,
Smart Key Control Module, Clutch Switch
TURN
15A
BCM
Driver’s side fuse panel

1.#1
,204/3424-3
FFuse Name
Symbol
Fuse rating
Circuit Protected
MDPS
1
10A
MDPS Unit
MODULE1
10A
BCM, Sport Mode Switch, Stop Lamp Switch
MODULE 4
10A
BCM, Smart Key Control Module
A/CON 1
1A/C
10A
PCB Block (Blower Relay), A/C Control Module, Cluster Ionizer ( Auto A/C)
WASHER
15A
Multifunction Switch
MODULE 5
10A
Head Lamp Leveling Device Switch, Head Lamp Leveling Device Actuator LH/RH,
BCM, PCB Block (H/Lamp HI Relay)
A/BAG IND
10A
Instrument Cluster
AUDIO
20A
Audio
ROOM LP
10A
Luggage Lamp, Room Lamp, BCM, Hazard Switch & Door Lock Switch, Map Lamp,
Center Room Lamp, Data Link Connector, Digital Clock, Instrumen t Cluster,
A/C Control Module
Driver’s side fuse panel

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

1.',204/3424-3LLow Beam Assist-Static Light1. Open the hood.
2. Remove the Low Beam Assist-
Static Light bulb cover by turning it
counterclockwise.
3. Disconnect the Low Beam Assist- Static Light bulb socket-connector.
4. Unsnap the Low Beam Assist- Static Light bulb retaining wire by
depressing the end and pushing it
upward.
5. Remove the bulb from the Low Beam Assist-Static Light assem-
bly. 6. Install a new Low Beam Assist-
Static Light bulb and snap the Low
Beam Assist-Static Light bulb
retaining wire into position by
aligning the wire with the groove
on the bulb.
7. Connect the Low Beam Assist- Static Light bulb socket connector.
8. Install the Low Beam Assist-Static Light bulb cover by turning it clock-
wise.
Parking (Position) light1. Remove the socket from theassembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light or Daytime runninglight (if equipped)
OIB075061
Low Beam Assist-Static Light
OIB077071OIB077072OIB077073
■
5 Door
• Type A (without DRL)■5 Door
• Type A (with DRL)■ Cross

1.'&
,204/3424-3
1. Remove the under cover by rotat-ing the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulb-socket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulb-socket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
PPosition light/Daytime running light(if equipped)Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, we recommend
that the vehicle be checked by an
authorized HYUNDAI dealer.
Side repeater light (LED)
replacement (if equipped)If the light does not operte, we rec-
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
OIB074035

1.'),204/3424-3
1. Using a flat-blade screwdriver, remo ve the light assembly from
the body of the vehicle by prying
the housing and pulling the
assembly out.
2. Separate the socket and the lens part by turning the socket counter-
clockwise until the tabs on the
socket align with the slots on the
lens part.
3. Remove the bulb by pulling it straight out.
4. Insert a new bulb in the socket.
5. Reassemble the socket and the housing part.
6. Reinstall the light assembly to the body of the vehicle.
IInterior light bulb replacement1. Using a flat-blade screwdriver,
gently pry the lens from the interi-
or light housing. 2. Remove the bulb by pulling it
straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior light housing notches and snap
the lens into place.
Be careful not to dirty or damage
lens, lens tab, and plastic housings. NOTICE
■ Room lamp■Luggage room lamp
OIB074042OIB074041
OIB074040
■Cross