2014 HONDA INSIGHT ECU

Remove the socket f rom the f ront
turn signal light assembly by
turning it one-quarter turn
counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
f ront turn signal light assembly.
Turn it clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Install the garnish in the original
position securely.
Placeaclothonthenotchof the
light assembly garnish to prevent
scratches. Remove the cover by
caref ully prying in the notch with a
f lat-tip screwdriver. Remove the bolts and pull the
f ront turn signal light assembly
from the bumper while taking the
tab out from the holder.
Install the light assembly in the
reverse order of removal. Make
sure to secure the bolts.
5.
6.
1. 7.
8.
3. 4.
2.
Lights
Replacing the Front
Turn Signal Light Bulb
325
NOTCH
COVER
BOLTSBULB
SOCKET
12/07/13 17:18:12 31TM8630_330
Maint enanceTOC
2014 Insight

Install the new bulb in the socket
by pushing it straight in the socket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Reinstall and
tighten the two mounting bolts.To reinstall the trim, set the
bottom edge of the trim in the
original position and push the
bottom half of the trim to clip it
back securely. Then push the
upperhalfofthetrimtosecure
the top clip. Secure the hooks by pushing on
the areas of the trim as shown in
the illustration above.
11.
12.
13.
14.
15.16.
Lights
329
12/07/13 17:18:43 31TM8630_334
Maint enanceTOC
2014 Insight

Before using an automatic car
wash, remove the audio antenna
so it does not get damaged. Remove
the antenna by unscrewing it.
When you reinstall the antenna,
tighten it securely.
Before entering or parking
in areas with low ceiling height,
remove the antenna.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. To lock each
anchor, turn the knob clockwise.
This keeps the f loor mat f rom sliding
f orward and possibly interf ering with
the pedals.
If your seat belts get dirty, use a soft
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air dry before
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
When cleaning or replacing, turn the
knob counterclockwise to unhook
the floor mat.
CONT INUED
On LX and EX models
Floor Mats
Cleaning the Seat Belts
A udio A ntenna
A udio A ntenna, Cleaning the Seat Belts, Floor Mats
331
LOOP
To unlock
Driver’s floor mat is shown.
12/07/13 17:18:59 31TM8630_336
Maint enanceTOC
2014 Insight

´
Wheels:
Tires:
See page f or DOT tire quality
grading information, and page 384
f or tire size inf ormation. Tires marked ‘‘M S’’ or ‘‘All
Season’’ on the sidewall have an all-
weather tread design suitable for
most winter driving conditions.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
If you mount snow tires on your
vehicle, make sure they are radial
tires of the same size and load range
as original tires. Mount snow tires on
all f our wheels. The traction
provided by snow tires on dry roads
maybelowerthanyouroriginaltires.
Check with the tire dealer f or
maximum speed recommendations.
Because your vehicle has limited tire
clearance, Honda strongly
recommends using the chains listed
below, made by Security Chain
Company (SCC). Mount tire chains on your tires when
required by driving conditions or
local laws. Install them only on the
f ront tires.
Cable-type: SCC RADIAL CHAIN
SC1026
382
Wheel and T ire Specif ications Winter Driving
Snow T iresT ire Chains
Tires
342
15x6J
P185/60R15 84T
Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.
12/07/13 17:20:33 31TM8630_347
Maint enanceTOC
2014 Insight

Before mounting the spare tire,
wipe any dirt off the mounting
surface of the wheel and hub
with a clean cloth. Wipe the
hub carefully; it may be hot
from driving.Lower the vehicle to the ground,
and remove the jack. Put on the spare tire. Put the
wheel nuts back on f inger-tight,
then tighten them in a crisscross
pattern with the wheel nut wrench
until the wheel is f irmly against
the hub. Do not try to tighten the
wheel nuts f ully.
Tighten the wheel nuts securely in
the same crisscross pattern.
Have the wheel nut torque
checked at the nearest
automotive service facility.
Tighten the wheel nuts to:
18.
17. 16.
15.
Changing a Flat Tire
352
BRAKE HUB
80 lbf·ft (108 N·m , 11 kgf·m)
12/07/13 17:21:43 31TM8630_357
T aking Care of t he Unexpect edTOC
2014 Insight

CONT INUED
Place the flat tire face down in the
spare tire well.Remove the spacer cone f rom the
wing bolt, turn it over, and put it
back on the bolt.
Remove the carpet from the Securetheflattirebyscrewing
the wing bolt back into its hole.
Store the box in the wheel of the
flat tire.
Remove the center cap (if
equipped) bef ore storing the f lat
tire in the cargo area well.
Install the spare tire casing in
20.
21.
19.
22.23.
24.EX models
Changing a Flat Tire
353
SPACER CONE
WING BOLT
For normal tire
For compact
spare tire
CARPET
SPARE TIRE
CASING
CENTER CAP BOX
12/07/13 17:21:52 31TM8630_358
T aking Care of t he Unexpect edTOC
spare tire casing and store it in
the casing.
tire well. the original position in the spare
2014 Insight

Your vehicle’s original tire has a
tire pressure monitoring system
sensor. To replace a tire, ref er to(see
page ).
Store the center cap in the cargo
area. Make sure it does not get
scratched or damaged.
Store the tools in the spare tire
casing and the jack in its holder.
Turn the jack’s end bracket
clockwise to lock it in place, and
reinstall the cover.
Place the cargo area f loor in its
original position. Close the hatch.
25.
26.27.
28.
291
U.S. models only
Changing a Flat Tire
Changing a T ire with T PMS
354
FLOOR
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.
12/07/13 17:21:58 31TM8630_359
T aking Care of t he Unexpect edTOC
2014 Insight

CONT INUED
................................................
Keys .129
.................
Jacking up the Vehicle . 351
.......................................
Jack, Tire .350
................................
Jump Starting .358
Indicators, Messages (MID)
.....................................
Lights On .69
......................................
Low Fuel .70
................
Low Oil Pressure . 62, 363
.....
Low Temperature (Coolant) . 67
Low Tire Pressure/ ...............................
TPMS .66, 289
...
Malf unction Indicator Lamp . 365
..........................
Security System .70
...........................
Side Airbag Of f .65
.................................
Seat Belt .21, 62
.........................................
SRS .34, 64
.........................
System Message .70
...........................
TPMS .66, 289, 290
Turn Signal and Hazard ...................................
Warning .69
12 Volt Battery Charging ..............................
System .63, 364
........................................
VSA Off .65
.................................
VSA System .65
...............................
Inf ant Restraint .43
Inf ant Seats ......
LATCH Anchorage System . 47
...........................
Lower Anchors .47
...........................
Tether Anchors .51 .....
Inf lation, Recommended Tire . 338
...................................
Pressures . 339
........................
Inf ormation Display .72
.................................
Inside Mirror .147
.............................
Inspection, Tire .339
............................
Instrument Panel .61
......
Instrument Panel Brightness . 124
...............................
Interior Lights .159
........................................
Introduction .i
...............................................
iPod
. 195
.......................
Label, Certif ication .378
...............
Lane Change, Signaling . 121
..................
Lap/Shoulder Belts . 17, 22 ...........
LATCH Anchorage System . 47
Lights ....................
Bulb Replacement .321
.......................................
Indicator . 69
.......................................
Parking .120
..........................
Turn Signal .69, 120
....................................
Load Limits .257
....
LOCK (Ignition Key Position) . 131
Locks .....
Anti-thef t Steering Column . 131
............................
Fuel Fill Door .245
..........................................
Hatch .139
...............................
Power Door .133
........................
Low Coolant Level .250
.........................
Low Fuel Indicator .70
................................
Lower Anchors . 47
...
Low Oil Pressure Indicator . 62, 363
...
Lubricant Specif ications Chart . 380
INDEX
V
12/07/23 10:21:38 31TM8630_408
IndexA B C D E F G H I J K L M N O P Q R S T U V W X Y Z
J
K L
2014 Insight