2014 HONDA INSIGHT height

Seepage f or important saf ety
inf ormation and a warning about improperly positioning head restraints. 16
Your vehicle is equipped with head
restraints in all seating positions to
help protect you and your
passengers f rom the likelihood of
whiplash and other injuries.
They are most ef f ective when you
adjust them so the center of the back
of the occupant’s head rests against
the center of the restraint.The front and rear outer head
restraints adjust f or height. You
need both hands to adjust the
restraint. Do not attempt to adjust it
while driving. To raise it, pull upward.
To lower the restraint, push the
release button and push the
restraint down.
Head Restraints
A djust ing t he Head Rest raint
Seats
142
LEGS
SEAT-BACK RELEASE
BUTTON
Front Position
CUSHION
12/07/13 16:54:55 31TM8630_147
Inst rument s and Cont rolsTOC
2014 Insight

To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.
When a passenger is seated in the
rear center seating position, the
center head restraint should be
adjusted up or down, to match the
passenger’s height. The seat-back must be f olded
forward (see
page) to get ceiling
clearance f or removal of the head
restraints. 145
CONT INUED
For Rear Seat Head Restraints
Removing t he Head Rest raint
Seats
143
LEGS SEAT-BACK
SEAT-BACK
LEGS RELEASE
BUTTON
Rear Outer Position
Rear Center Position
CUSHION
RELEASE
BUTTON
CUSHION
12/07/13 16:55:02 31TM8630_148
Inst rument s and Cont rolsTOC
2014 Insight

After a collision, the activated
restraint should return to its
normal position.
If the restraints do not return to their
normal position, or in the event of a
severe collision, have the vehicle
inspected by a Honda dealer.
This reduces the distance between
the restraint and the occupant’s head.
It also helps protect the occupants against the likelihood of whiplash
and injuries to the neck
and upper spine.
The driver’s and f ront passenger’s
seats have active head restraints. If
the vehicle is struck severely f rom
the rear, the occupant properly
secured with the seat belt will be
pushed against the seat-back and the
head restraint will automatically
move forward.
Make sure the head restraint locks
in position when you reinstall it. When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
A ct ive Head Rest raint s
Seats
144
Failure to reinstall, or correctly
reinstall, the head restraints can
result in severe injury during a
crash.
Always replace the head
restraints before driving.
12/07/13 16:55:09 31TM8630_149
Inst rument s and Cont rolsTOC
2014 Insight

Before using an automatic car
wash, remove the audio antenna
so it does not get damaged. Remove
the antenna by unscrewing it.
When you reinstall the antenna,
tighten it securely.
Before entering or parking
in areas with low ceiling height,
remove the antenna.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. To lock each
anchor, turn the knob clockwise.
This keeps the f loor mat f rom sliding
f orward and possibly interf ering with
the pedals.
If your seat belts get dirty, use a soft
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air dry before
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
When cleaning or replacing, turn the
knob counterclockwise to unhook
the floor mat.
CONT INUED
On LX and EX models
Floor Mats
Cleaning the Seat Belts
A udio A ntenna
A udio A ntenna, Cleaning the Seat Belts, Floor Mats
331
LOOP
To unlock
Driver’s floor mat is shown.
12/07/13 17:18:59 31TM8630_336
Maint enanceTOC
2014 Insight

Î
Î
Î
Î
Specif ications
380
Dimensions
Weights
Seating CapacitiesCapacities
Engine 172.3 in (4,377 mm)
66.7 in (1,695 mm)
56.2 in (1,427 mm)
100.4 in (2,550 mm)
58.3 in (1,481 mm)
58.0 in (1,472 mm)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating See the certification label attached
to the driver’s doorjamb. 3.4 US qt (3.2
)
3.2 US qt (3.0)
4.0 US qt (3.8)
Total
Front
Rear 5
2
3
Excluding the oil remaining in the engine Including the coolant in the reserve tank and that remaining in the
engine
Reserve tank capacity: 0.116 US gal (0.44
)
2.6 US qt (2.5
)
4.76 US qt (4.50)
Fuel tank
Engine
coolant
Engine oil
Automatic
transmission
fluid (CVTF)
Windshield
washer
reservoir
Type
BorexStroke
Displacement
Compression ratio
Spark plugs 10.8 : 1
82 cu-in (1,339 cm
)
2.87 x 3.15 in (73.0 x 80.0 mm) 3.0 US qt (2.8
)
5.5 US qt (5.2)
10.6 US gal (40
)
1.165 US gal (4.41)
1.295 US gal (4.90)
Water cooled 4-stroke SOHC i-VTEC gasoline engine with Hybrid Electric Motor
DILFR6J11
Front
Rear
Approx.
1:
2: Change
Total
Change
Including filter
Without filter
Total
Change
Total
U.S. Vehicles
Canada Vehicles
(NGK)
1
2
12/07/13 17:24:52 31TM8630_385
Technical Inf ormationTOC
2014 Insight

µ
µ µ
µ
µ
µ
µ
µµ
µ
µ
µ
µ
µ Tire type code.
Date of manufacture.
Load index (a numerical code
associated with the maximum
load the tire can carry).
Speed symbol (an
alphabetical code indicating
the maximum speed rating).
The tire identif ication number (TIN)
is a group of numbers and letters
that look like the f ollowing example.
TIN is located on the sidewall of the
tire.
This indicates that the tire
meets all requirements of
the U.S. Department of
Transportation. Year
Week
Manuf acturer’s
identification mark. Cold Tire Pressure The tire air
pressure when the vehicle has been
parked f or at least three hours or
drivenlessthan1mile(1.6km).
Load Rating Means the maximum
load that a tire is rated to carry for a
given inf lation pressure.
Maximum Inf lation Pressure The
maximum tire air pressure that the
tire can hold.
Whenever tires are replaced, they
should be replaced with tires of the
same size. Following is an example
of tire size with an explanation of
what each component means.
Rim diameter in inches. Tire construction code (R
indicates radial). Aspect ratio (the tire’s section
height as a percentage of its
width). Tire width in millimeters. Vehicletype(Pindicates
passenger vehicle).
R DOT2202
15 84
EUYU2KNR
T
60 185 P
Tire Labeling
Tire Size T ire Ident if icat ion Number (T IN)
Glossary of T ire T erminology
384
DOT EUYU 2KNR 2202
P185/60R15 84T
12/07/13 17:25:46 31TM8630_389
Technical Inf ormationTOC
2014 Insight