2014 HONDA CIVIC SEDAN maintenance

379
uuReplacing Light Bulbs uHeadlight Bulbs
Maintenance
2. Remove the holding clip (C) using a flat-tip
screwdriver, then remo ve the upper part of
the windshield washer reservoir.
3. Push the tab to remove the coupler.
4. Rotate the old bulb to the left to remove.
5. Insert a new bulb into the headlight
assembly and turn it to the right.
6. Insert the coupler into the connector of the
bulb.
1 Low Beam Headlights
Insert a flat-tip screwdriver, lift and remove the center
pin to remove the clip.
Insert the clip with the center pin raised, and push
until it is flat.
Holding clip (C-type)
Center pin
Push until the
pin is flat.
Clip (C)Passenger side
All models
Tab
Coupler
Bulb
Both sides
All models
14 CIVIC 4D_SI-31TR36210.book 379 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

380
uuReplacing Light Bulbs uFog Light Bulbs*
Maintenance
Fog Light Bulbs*
When replacing, use the following bulbs.
1.Insert a flat-tip screwdriver into the tab on
the cover, then pull stra ight out as indicated
to remove the cover.
Fog Light: 55 W (H11 for halogen bulb type)
Fog Light: 35 W (H8 for halogen bulb type)
1 Fog Light Bulbs*
NOTICE
Halogen bulbs get very hot wh en lit. Oil, perspiration,
or a scratch on the glass can cause the bulb to
overheat and shatter.
When replacing a halogen bulb, handle it by its
plastic case, and protect th e glass from contact with
your skin or hard objects. If you touch the glass, clean
it with denatured alc ohol and a clean cloth.
1.8 ℓ models
2.4 ℓ models
TabCover1.8 ℓ models
2.4 ℓ modelsTabCover
* Not available on all models
14 CIVIC 4D_SI-31TR36210.book 380 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

381
uuReplacing Light Bulbs uFog Light Bulbs*
Continued
Maintenance
2. Remove the screws using a Phillips-head
screwdriver and carefu lly pull the fog light
assembly out of the bumper.1.8 ℓ models
2.4 ℓ models
Screws
Screws
14 CIVIC 4D_SI-31TR36210.book 381 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

382
uuReplacing Light Bulbs uFog Light Bulbs*
Maintenance
3. Push the tab to remove the coupler.
4. Rotate the old bulb to the left to remove.
5. Insert a new bulb into the fog light
assembly and turn it to the right.
6. Insert the coupler into the connector of the
bulb.1.8 ℓ models
2.4 ℓ modelsTab
CouplerBulb
Tab
CouplerBulb
14 CIVIC 4D_SI-31TR36210.book 382 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

383
uuReplacing Light Bulbs uFront Turn Signal/Parking/Side Marker Light Bulbs
Continued
Maintenance
Front Turn Signal/Parking/Side Marker Light Bulbs
When replacing, use the following bulbs.
1.Turn the steering wheel all the way to the
opposite side from the light being replaced.
Passenger side: Turn the steering wheel
to the left.
Driver side: Turn the steering wheel to the
right.
2. Remove the holding clips, and pull the inner
fender back.
2 Low Beam Headlights P. 379
3.Detach the air intake duct tube and swing it
out of the inner fender.
Front Turn Signal/Parking/Side Marker Light: 28/8 W (Amber)
Clip
Inner
Fender
Air
Intake
Duct
Tube
2.4 ℓ engine models
14 CIVIC 4D_SI-31TR36210.book 383 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

384
uuReplacing Light Bulbs uFront Turn Signal/Parking/Side Marker Light Bulbs
Maintenance
4. Turn the socket to the left and remove it,
then remove the old bulb.
5. Insert a new bulb.
Bulb Socket
All models
14 CIVIC 4D_SI-31TR36210.book 384 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

385
uuReplacing Light Bulbs uBrake/Taillight, Rear Turn Signal Light and Rear Side Marker Light Bulbs
Maintenance
Brake/Taillight, Rear Turn Si gnal Light and Rear Side
Marker Light Bulbs
When replacing, use the following bulbs.
1.Remove the holding cl ips using a flat-tip
screwdriver, then pull the lining back.
2. Turn the socket to th e left and remove it.
3. Remove the old bulb and insert a new bulb.
Brake/Taillight: 21/5 W
Rear Turn Signal Light: 21 W (Amber)
Rear Side Marker Light: LED
1Brake/Taillight, Rear Turn Signal Light and Rear Side Marker Light
Bulbs
Rear side marker light bulbs are LED type. Have an
authorized Honda dealer in spect and replace the light
assembly.
When removing the clip, insert a flat-tip screwdriver,
then lift and remove the clip.
Insert the clip with the pin raised, and push until it is
flat.
Clip
Push until the
pin is flat.
Lining
Clip
BulbSocket
BulbSocket
14 CIVIC 4D_SI-31TR36210.book 385 ページ ２０１４年１月３０日　木曜日　午後１２時１８分

386
uuReplacing Light Bulbs uTaillight and Back-Up Light Bulbs
Maintenance
Taillight and Back-Up Light Bulbs
When replacing, use the following bulbs.
1.Remove the screw from the center of the
fastener using a Phillips-head screwdriver.
2. Remove the holding clips using a flat-tip
screwdriver, then pull the lining back.
2Brake/Taillight, Rear Turn Signal Light
and Rear Side Marker Light Bulbs
P. 385
3. Turn the socket to the left and remove it.
4. Remove the old bulb and insert a new bulb.
Back-Up Light: 16 W
Taillight: 3 CP
Lining
Fastener
Clip
Models with trunk lid lining
Bulb
Socket
Bulb
Socket
All models
14 CIVIC 4D_SI-31TR36210.book 386 ページ ２０１４年１月３０日　木曜日　午後１２時１８分