2014 FIAT PUNTO lock

125
SAFETYSTARTING
AND DRIVINGIN AN
EMERGENCYSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESWARNING
LIGHTS AND
MESSAGES
DOOR OPEN (red)
On certain versions, the warn-
ing light turns on when one or
more doors or the boot are not proper-
ly closed.
A specific message is displayed on certain
versions.
You will hear a warning sound if a door
is open and the car is moving.
´
“DUALDRIVE”
ELECTRIC POWER
STEERING FAILURE (red)
This warning light comes on
when the ignition key is turned to MAR,
but it should go off after a few seconds.
If the warning light stays on, you will not
get the benefit from the electric power
steering and the effort needed to turn the
wheel will be greatly increased, although
it will still be possible to steer the car.
Contact a Fiat Dealership.
A specific message is displayed on certain
versions.
g
EBD FAULT
(red)
(amber)
Warning lights
x
and
>
lit at the same
time with the engine running indicates an
EBD system failure or that the system is
not available. This may cause premature
locking of the rear wheels in the event of
violent braking, causing the car to swerve.
Drive very carefully to a Fiat Dealership to
have the system inspected immediately.
A specific message is displayed on certain
versions.
x
>LOW ENGINE OIL
LEVEL (red)
(for versions/markets, where
provided)
When turning the ignition key to MAR,
the warning light turns on but it should go
off after a few seconds.
This warning light where provided comes
on when the engine oil level falls below the
minimum recommended value. Restore
the correct engine oil level (see “Check-
ing fluid levels” in the “Servicing and care”
section).
A specific message is displayed on certain
versions.
k
Exhausted engine oil should
be replaced as soon as pos-
sible after the warning light comes on,
never more than 500 km after the
warning light first comes on. Failure
to change the oil within the first 500
km may result in severe damage to
the engine and will result in forfeiture
of the warranty. Remember that
when the warning light flashes, it does
not mean that the level of engine oil
is low, so if the light flashes you must
not top up.
WARNING
For versions/markets, where
provided:
the
v
warning light turns on and flash-
es along with the message on the display
(if applied) when the system detects that
the engine oil is exhausted. The flashing of
the warning light should not be considered
as a fault, rather simply informs the driver
that oil needs to be changed after a stan-
dard period of car utilisation. If the oil is
not changed, when reaching a second de-
terioration threshold, also the warning
light
U
switches on in the instrument
panel and the engine operation is limited
at 3000 rpm.
If the oil is still not changed, when reaching
a third deterioration threshold, the engine
is limited at 1500 rpm to avoid damage.
WARNING! To avoid dam-
aging the engine it is recom-
mended to change the en-
gine oil when the warning light
v
flashes. Contact a Fiat Dealership.
121-132 PUNTO POP 1ed EN 29/08/13 15.03 Pagina 125

136SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
Important notes:❒
the jack weight is 1.76 kg;
❒
the jack requires no adjustment;
❒
the jack cannot be repaired. If it breaks
it must be replaced with a new jack;
❒
no tool other than its cranking device
may be fitted on the jack.
To change a wheel proceed
as follows:
❒
stop the car where it is not a danger to
other road users and you can replace
the wheel safely. The ground should be
flat and solid;
❒
turn the engine off and pull up the hand-
brake.
❒
engage first gear or reverse;
❒
wear the reflective safety jacket (com-
pulsory by law in certain countries) be-
fore getting out of the car;
❒
open the boot and lift the carpet or re-
move the cargo box (for versions/mar-
kets, where provided);
❒
unscrew the locking device A-fig. 2;
❒
take out the tool container C-fig. 2and
put it alongside the wheel to be
changed;
❒
take out the spare wheel B-fig. 2;
fig. 2
F0M0188m
The jack may be used to re-
place wheels only on the car
which it equips or other cars of the
same model. Never use the jack for
other purposes, such as lifting other
models. Never use the jack to carry
out repairs under the car. Incorrect
positioning of the jack may cause the
car to fall. Do not use the jack for
loads higher than the one shown on
its label.
WARNING
Incorrect hub cap assembly
may cause it to come off
when the car is moving. Never tam-
per with the inflation valve. Never in-
troduce tools of any kind between the
rim and the tyre. Check tyre and
spare wheel pressure regularly, refer-
ring to the values shown in the “Tech-
nical specifications” section.
WARNING
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 136

144SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
if you get a pressure reading of at least
1.8 bar, restore the proper pressure
(with engine running and handbrake on)
and restart;
❒
drive with the utmost care to the near-
est Fiat Dealership.
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor may also be used for
restoring pressure only. Release the fast
coupling and connect it directly to the tyre
valve fig. 13; in this way, the cylinder will
not be connected to the compressor and
no sealant will be injected. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder, proceed as fol-
lows:
❒
disconnect A-fig. 14;
❒
turn the cylinder anticlockwise to lift
it out;
❒
insert the new cylinder and turn it
clockwise;
❒
connect Ato the cylinder and fit the
transparent tube Binto its allocated
space.
Remember to inform the
workshop that the tyre has
been treated with a quick repair kit.
Give the instruction booklet to the
personnel charged with handling the
treated tyre.
WARNING
fig. 13
F0M0365m
fig. 14
F0M0206m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 144

145
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
CHANGING A BULB GENERAL INSTRUCTIONS❒
When a light is not working, check that
the corresponding fuse is intact before
changing the bulb. For the location of
fuses, refer to the “Changing a fuse”
paragraph in this section;
❒
before changing a bulb check the con-
tacts for rusting;
❒
burnt bulbs must be replaced by others
of the same type and wattage;
❒
for safety reasons, always check the di-
rection of the headlight beam after
changing a bulb.
IMPORTANT The internal surface of the
light may appear slightly misty: this does
not indicate a fault, and is actually caused
by low temperature and the degree of hu-
midity in the air. Misting will rapidly dis-
appear when the headlights are switched
on. The presence of drops inside the head-
lights indicates infiltration of water. Go to
a Fiat Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your
car:
AGlass bulbs: clipped into position. Pull
to remove.BBayonet-type bulbs: to remove from
its holder, press the bulb in and turn
it anti-clockwise.
CTubular bulbs: release them from
their contacts to remove.
D-EHalogen bulbs: to remove the bulb,
release the clip holding the bulb in
place. Halogen bulbs must be han-
dled holding the metallic part
only. Touching the transpar-
ent part of the bulb with your
fingers may reduce the intensity of the
light emitted and even compromise the
longevity of the bulb itself. In the event
of accidental contact, wipe the bulb
with an alcohol-soaked cloth and leave
to dry.
Modifications or repairs to
the electrical system (ECUs)
that are not carried out properly or
do not take the system’s technical
specifications into account can cause
malfunctions leading to the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas which may cause
small fragments of glass to be pro-
jected outwards if the bulb is broken.
WARNING
fig. 15
F0M0207m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 145

147
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
CHANGING AN
EXTERIOR BULBFor the type of bulb and relative power
rating, see “Changing a bulb”.
FRONT LIGHT CLUSTERS
fig. 16
The front light clusters contain sidelights,
dipped beam, main beam and direction in-
dicator bulbs.
The bulbs are arranged inside the light
cluster as follows:
Asidelights
Bdaytime running lights
Cdirection indicators
Dmain beam/dipped beam headlights.
IMPORTANT You can replace the front
direction indicator, main beam and dipped
beam headlight bulbs through the access
flap (see “Direction indicators” in this sec-
tion).SIDELIGHTS fig. 17
To change the bulb, proceed as follows:
❒
remove the rubber cap by pulling the
flap;
❒
press in tabs Band remove the bulb
holder;
❒
remove the bulb C and replace it;
❒
refit the bulb holder and then refit the
cap, ensuring that it locks into place.
fig. 16
F0M0630m
fig. 17
F0M0631m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 147

148SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
DAYTIME RUNNING LIGHTS
(DRL)
To change the bulb, proceed as follows:❒
turn the bulb holder A-fig. 18anti-
clockwise using the tab and pull it out;
❒
remove the bulb Bby pushing it in
slightly and turning it anti-clockwise;
❒
refit the bulb holder by putting it in its
housing and turning it clockwise until it
locks into place.MAIN/DIPPED BEAM
HEADLIGHTS fig. 19
To change the bulb, proceed as follows:
❒
remove the rubber cap;
❒
disconnect the central electric connec-
tor B-fig. 19and release the bulb hold-
er catch;
❒
remove the bulb Aand replace it;
❒
fit the new bulb, aligning the outlines of
the metallic part with the grooves on
the reflector;
❒
refit the bulb holder catch and recon-
nect the electrical connector;
❒
refit the cap, ensuring that it locks in-
to place.DIRECTION INDICATORS
Front fig. 20
To change the bulb, proceed as follows:
❒
steer the right/left wheel inwards;
❒
turn the catch A-fig. 20, then lift off the
access lid B;
fig. 18
F0M0632m
fig. 19/b
F0M0634m
fig. 19/a
F0M0633m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 148

149
SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
remove the bulb holder cover C-
fig. 21by turning it anti-clockwise;
❒
remove the bulb D-fig. 22by pushing
it in gently and turning anti-clockwise
(“bayonet” clamping), then replace it;
❒
refit the bulb holder cover C-fig. 21by
turning it clockwise and locking it prop-
erly;
❒
close the lid B-fig. 20then tighten the
catch A.Side fig. 23
To change the bulb, proceed as follows:
❒
slide the lens Atowards the front of
the car to press in the internal catch B,
then pull the unit outwards;
❒
turn the bulb holder Canti-clockwise,
extract bulb Dand replace it;
❒
refit the bulb holder Cinto the lens by
turning it clockwise;
❒
refit the unit making sure the internal
catch Bclicks into place.FRONT FOG LIGHTS
(for versions/markets where provided)
To replace the bulb:❒
loosen the screw A-fig. 24and re-
move the protection template B;
❒
loosen the fixing screwsCand re-
move the headlamp;
fig. 20
F0M0635m
fig. 21
F0M0636m
fig. 24
F0M0638m
fig. 23
F0M0637m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 149

150SAFETYSTARTING
AND DRIVINGWARNING
LIGHTS AND
MESSAGESSERVICE
AND CARETECHNICAL
SPECIFICATIONSINDEXCONTROLS
AND DEVICESIN AN
EMERGENCY
❒
remove the bulb A-fig. 25by ro-
tating it counter-clockwise and dis-
connect the electrical connector.
REAR LIGHT CLUSTERS
The rear light clusters contain taillight,
brake light and direction indicator bulbs.
The bulbs are arranged inside the light
cluster fig. 26as follows:
Ddirection indicators
Ebrake lights.
To change the bulb proceed as follows:❒
undo both fastening bolts A-fig 26;
❒
disconnect the central electric connec-
tor Band pull the lens unit outwards;
❒
unhook the bulb holder by unclipping
the fasteners C-fig. 27;
❒
remove the bulb by pushing it in gen-
tly and turning anti-clockwise (“bayo-
net” clamping), then replace it;
❒
refit the bulb holder;
❒
reconnect the electric connector, cor-
rectly realign the unit with the car body
and then tighten the fastening screws
A.IMPORTANT To replace the LED tail-
lights you must contact a Fiat Dealership.
fig. 25
A
F0M0639m
fig. 26
F0M0640m
fig. 27
F0M0641m
133-164 PUNTO POP 1ed EN 29/08/13 15.07 Pagina 150