2014 Citroen DS3 gearbox

11 9
DS3_en_Chap06_conduite_ed01-2014
Going into engine START mode
The "EcO" warning   lamp   goes   off  a
nd   the   engine   starts:
-

w

ith a manual gearbox , when you
depress the clutch pedal,
-

w

ith a 5-speed or 6-speed electronic
gearbox :
●
 
g

ear   lever   in   position   A or M, when you
release
  the   brake   pedal,
●
 
o

r
 
gear   lever   in   position   N   and   the   brake  
p

edal   released,   when   you   move   the   gear  
l

ever to position A or M ,
●
 
o

r
 
when   you   engage   reverse   gear.
Special cases: START invoked
automatically
If the system has been deactivated in   STOP   mode,   the   engine   restarts  
i

mmediately.
At
 
any   time,   press   the   "E
cO O
FF" switch to
deactivate   the   system.
This
 
is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   a   message   in   the  
sc

reen.
deactivation
For reasons of safety and for your comfort, S
TART   mode   is   invoked   automatically   when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
 
t
he   speed   of   the   vehicle   exceeds   7   mph  
(11
  km/h)   with   the   electronic   gearbox  
s

ystem,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
The "E
c
O
"
 
warning   lamp   flashes   for  
a

  few   seconds,   then   goes   off.
This operation is perfectly normal.
With
 
a
 
manual
 
gearbox
 
in
 
STOP
 
m

ode,
 
if
 
you
 
engage
 
a
 
gear
 
without
 
f

ully
 
depressing
 
the
 
clutch
 
pedal,
 
a
 
m

essage
 
is
 
displayed
 
asking
 
you
 
to
 
f

ully depress the clutch pedal so that
the
 
engine
 
can
 
restart.
driving

121
DS3_en_Chap06_conduite_ed01-2014
Hill start assist
System which holds your vehicle temporarily (approximately   2   seconds)   when   starting   on   a  
s

lope,   the   time   it   takes   to   move   your   foot   from  
t

he   brake   pedal   to   the   accelerator   pedal.
This
  function   is   only   active   when:
-
 
t
he   vehicle   is   completely   stationary,   with  
y

our   foot   on   the   brake   pedal,
-
 
c
ertain   conditions   on   a   slope   are   met,
-
 
w
ith   the   driver’s   door   closed.
The hill start assist function cannot be
deactivated.
On an ascending slope, with the vehicle
stationary, the vehicle is held momentarily
when you release the brake pedal:
-
 
p
rovided   you   are   in   automated   mode  
(

position A)
  or   in   manual   mode   (position   M)
on
  an   electronic   gearbox.
Do not leave the vehicle while it is
being
  held   in   the   hill   start   assist   phase.
If you need to leave the vehicle with
the
  engine   running,   manually   apply  
t

he   parking   brake   then   ensure   that   the  
p

arking   brake   warning   lamp   is   on   (not  
f

lashing)   in   the   instrument   panel.Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.
Operating fault
If a malfunction of the system occurs, these warning   lamps   come   on.   Contact   a   CITROËN  
d

ealer   or   a   qualified   workshop   to   have   the  
s

ystem   checked.
driving

DS3_en_Chap06_conduite_ed01-2014
Cruise control
System which automatically maintains the speed   of   the   vehicle   at   the   value   programmed  
b

y the driver, without any action on the
accelerator
 ped

al.
The cruise control is switched on
 m

anually:
 it r

equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h),   as   well   as   the   engagement   of:
-
 
f
ourth   gear   on   a   manual   gearbox,
-
 
s
econd   gear   on   a   or   automatic   or   electronic  
g

earbox,   in   sequential   mode,
-
position A
  on   an   electronic   gearbox   or  
p

osition d  on   an   automatic   gearbox.
The cruise control is switched off
 m

anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or  
o

n   triggering   of   the   ESP   system   for   safety  
r

easons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value. The
  controls   of   this   system   are   grouped  
t

ogether   on   stalk   A.
1.
 C

ruise   control   mode   selection   thumb  
w

heel.
2.
 V

alue   decrease   button.
3.
 V

alue   increase   button.
4.
 C

ruise   control   off/resume   button.Steering mounted controls
The cruise control cannot, in any
circumstances,  replace   the   need   to r

espect   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.The
  programmed   information   is   grouped  
t

ogether   in   the   instrument   panel   screen.
5.
  C
ruise   control   off/resume   indication.
6.
  C
ruise   control   mode   selection   indication.
7.
  P
rogrammed   speed   value.
displays in the instrument panel

DS3_en_Chap10_info-pratiques_ed01-2014
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not   block   traffic:   the   ground   must   be  
l

evel,   stable   and   not   slippery.
Apply
  the   parking   brake,   switch   off   the  
i

gnition   and   engage   first   gear*   to   lock  
t

he   wheels.
If
  necessary,   place   a   chock   under   the  
w

heel   diagonally   opposite   the   wheel   to  
be c

hanged.
It
  is   imperative   that   you   ensure   that   the  
o

ccupants   get   out   of   the   vehicle   and  
w

ait   where   they   are   safe.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
List of operations
F Remove  the   chromed   bolt   cover   from   each  o
f   the   bolts   using   the   tool   3 (alloy wheels
only).
F
 
F
it   the   socket   4 on the wheelbrace 1 to
slacken
  the   security   bolt   (if   your   vehicle   is  
f

itted   with   them).
F
 
S
lacken   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
* position P
 
for
 
an
 
automatic
 
gearbox. Ensure
  that   the   jack   is   stable.   If   the  g
round   is   slippery   or   loose,   the   jack  
c

ould   slip   or   drop   -   Risk   of   injury!
Take
  care   to   position   the   jack   only   at  
o

ne   of   the   jacking   points   A or B under
the
  vehicle,   ensuring   that   the   vehicle's  
c

ontact sur face is well centred on the
head
  of   the   jack.   Other wise,   there   is   a  
r

isk   of   damage   to   the   vehicle   and/or   the  
j

ack   might   drop   -   Risk   of   injury!

DS3_en_Chap10_info-pratiques_ed01-2014
Fuse N°Rating Functions
F8 20 AMultifunction
  screen,   audio   system,   navigation   radio,   alarm  
c

ontrol   unit,   alarm   siren.
F9 30 A12
  V   socket,   portable   navigation   support   supply.
F10 15 ASteering
  mounted   controls.
F11 15 AIgnition,
  diagnostic   socket,   automatic   gearbox   control   unit.
F12 15 ARain
  /   sunshine   sensor,   trailer   relay   unit.
F13 5 AMain
  stop   switch,   engine   relay   unit.
F14 15 AParking
  sensors   control   unit,   airbag   control   unit,   instrument  
p

anel,   digital   air   conditioning,   USB   Box,   Hi-Fi   amplifier.
F15 30 ALocking.
F16 -Not
  used.
F17 40 ARear
  screen   and   door   mirrors   demisting/defrosting.
SH -PARC
  shunt.

DS3_en_Chap10_info-pratiques_ed01-2014
Fuse table
Fuse N°Rating Functions
F1 20 AEngine
  control   unit   supply,   cooling   fan   unit   control   relay,   multifunction   engine   control   main   relay,   injection   pump  
(

Diesel).
F2 15 AHorn.
F3 10 AFront
  /   rear   screenwash.
F4 20 ALED
  lamps.
F5 15 ADiesel
  heater   (Diesel),   particle   filter   additive   pump   (Diesel),   air   flow   sensor   (Diesel),   blow-by   heater   and  
e

lectrovalves   (VTi).
F6 10 AABS/ESP
  control   unit,   secondary   stop   switch.
F7 10 AElectric
  power   steering,   automatic   gearbox.
F8 25 AStarter
  control.
F9 10 ASwitching
  and   protection   unit   (Diesel).
F10 30 AFuel
  heater   (Diesel),   blow-by   heater   (Diesel),   fuel   pump   (VTi),   injectors   and   ignition   coils   (petrol).
F11 40 AHeater
 b

lower.

233
DS3_en_Chap10_info-pratiques_ed01-2014
Protect your eyes and face before
handling  the   battery.
All
  operations   on   the   battery   must   be  
c

arried out in a well ventilated area
away
  from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   and   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void  
t
he  
r
isk  
o
f  
e
xplosion.  
I
f  
t
he  
b
attery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop   who   will   check  
t

hat   the   internal   components   have   not  
b

een   damaged   and   the   casing   is   not  
c

racked,   which   could   cause   a   leak   of  
t

oxic   and   corrosive   acid.
Do not reverse the polarity and use
only
  a   12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
Do not push the vehicle to start the
engine
 
if
 
you
 
have
 
an
 
electronic
 
g

earbox
 
or
 
automatic
 
gearbox.charging the battery using
a battery charger
Batteries contain harmful substances such a s   sulphuric   acid   and   lead.   They   must   be d

isposed   of   in   accordance   with   regulations
 a

nd   must   not,   in   any   circumstances,   be
 d

iscarded   with   household   waste.
Take
  used   remote   control   batteries   and
 v

ehicle batteries to a special collection
point.
F Follow the instructions for use provided by the   manufacturer   of   the   charger.
Do
  not   disconnect   the   battery   to   charge   it.
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
Towing the vehicleProcedure for having your vehicle towed or for towing another vehicle using a removable towing eye.
T he   towing   eye   is   installed   in   the   boot   under  
t

he   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F

r
aise the floor,
F
 
r
emove   the   polystyrene   storage   box,
F
 
r
emove   the   towing   eye   from   the   holder.
Access to the tools General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
f

our-wheel drive vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...