2014 CITROEN DS3 CABRIO headlamp

217Practical information











Changing a bulb


The headlamps are fitted with polycarbonate glass with a protectivecoating:)do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,)
use a sponge and soapy water or apH neutral product,)
when using a high pressure washer on persistent marks, do notkeep the lance directed towards the lamps or their edges for too long, so as not to damage their protective coating and seals.


Front lamps
1.Direction indicators (PY21W amber).2.Sidelamps (W5W).3.Main beam headlamps (H1- 55W).4.Dipped beam headlamps (H7-55W).5.Front foglamps (PSX24W).6.
LED lamps (LEDs).
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of seriousburns). )Do not touch the bulb directly withyour fingers, use a lint-free cloth.It is imperative to use only anti-ultraviolet (UV) type bulbs to avoid damaging the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.

Changing direction indicator
bulbs
When refitting, close the protective cover carefully to preser ve the sealing of the headlamp.
Amber coloured bulbs, such as thedirection indicators, must be replacedwith bulbs of identical specificationsand colour.

Rapid flashing of the direction indicator warning lamp (right or left) indicates thefailure of a bulb on that side.
)Turn the bulb holder a quar ter of a turn and extract it. )Pull out the bulb and change it.
To r efit, carry out these operations in reverse order.
Changing dipped beam headlamp
bulbs
)Remove the protective cover by pulling the
t
ab. )Disconnect the bulb connector. )Spread the springs to release the bulb.)Pull the bulb out and change it.
To r efit, carry out these operations in reverse order.

219Practical information
Changing main beam headlamp
bulbs
)Remove the protective cover by pulling on
th
e tab. )Disconnect the bulb connector. )Spread the springs to release the bulb.)Remove the bulb and change it.
To r efit, carry out these operations in reverseorder.
Changing sidelamp bulbs
)
Remove the protective cover by pulling on
the tab.
) Pull the bulb holder pressing on the tabs on both sides. )
Pull the bulb and change it.
To r efit, carry out these operations in reverse order.

Changing integrated directionindicator side repeaters
)
Insert a screwdriver towards the centre of
the repeater between the repeater and the
base of the door mirror.) Tilt the screwdriver to extract the repeater and remove it. )
Disconnect the repeater connector.)
Replace the module.
To r efit, carry out these operations in reverse order.
Contact a CITROËN dealer or a qualified workshop to obtain areplacement side repeater module.

Fuse N°RatingFunctions
F1230 AWindscreen wipers slow / fast speed.
F1
340 ABuilt-in systems inter face supply (ignition positive).
F1
430 AValvetronic supply (VTi).
F1
510 ARight-hand main beam headlamps.
F16 10 ALe
ft-hand main beam headlamps.
F1715 ALeft-hand dipped beam headlamps.
F18 15
ARight-hand dipped beam headlamps.
F1
915 AOxygen sensors and electrovalves (VTi), electrovalves
(Diesel), EGR electrovalve (Diesel).
F20 10 APumps, electronic thermostat
(VTi), timimg electrovalve (THP), water in fuel sensor (Diesel).
F2
15 AFan assembly control supply, ABS/ESP, turbo pump (THP).

235
Practical information








Energy economy mode System which manages the period of use of cer tain functions to conser ve a sufficient level of charge in the battery.
After the engine has stopped, you can still use functions such as the audio equipment, windscreen wipers, dipped beam headlamps, cour tesy lamps,etc. for a maximum combined period of thir ty minutes.
This period may be greatly reduced if the battery is not fully charged.

A flat battery prevents the engine from starting (refer to the correspondingparagraph).
If the telephone is being used at thesame time on the eMyWay audionavigation system, it will be interrupted after 10 minutes.
Switching to economy mode
Once this period has elapsed, a message appears on the multifunction screen indicating
that the vehicle has switched to economy mode and the active functions are put on standby.

Exiting economy mode

These functions are reactivated automatically
the next time the vehicle is driven. ) In order to resume the use of thesefunctions immediately, star t the engine and
let it run for a few minutes.
The time available to you will then be double
the period for which the engine is left running. However, this period will always be between five and thir ty minutes.

305
10CONFIGURATION
Press SETUP
to display the"Confi guration
" menu.
Select " Choose colour" and confi rm torselect the screen colour harmony and
the map presentation mode:
- day mode,
- ni
ght mode,
- automatic da
y/night mode,according to whether the
headlamps are on.
Select " Adjust luminosity" and confi rm
to adjust the screen brightness.
Press " OK" to save the changes.
The settin
gs for day and night are independent.

Select " Display confi guration" andconfi rm.


Display configuration

309
11
2
3
3
1
4
2
2
1
4
4
2
2
Night mode

Auto Day/Night
Ad
just luminosity
Set date and time

"SETUP" MENU
Displa
y configuration
Choose colour


Harmony:

Carto
graphy:
Da
y mode


Speech synthesis setting
Guidance instructions volume
Select male voice/Select female voice
2Select units
SCREEN MENU MAP(S)
2
3
3
2Lighting confi guration
Parking assistance
Rear wiper in reverse
Guide-me-home li
ghting time
1

Define vehicle parameters *
2Wiper operation
3 Directional headlamps
3
Mood lighting
3
Daytime running lamps

*
The settin
gs vary according to the vehicle.
2Alert log
1Trip computer
2Status of functions
2Français
1

Select language
2English
2Italiano
2Portuguese
2Español
2Deutsch
2Nederlands
2Turkish
2Polski
2Русский

Exterior
- opening/closing
- anti-theft protection
- starting
- battery
Lighting controls 112-117
Headlamp adjustment 117
Changing bulbs 217-220
- front lamps
- foglamps
- direction indicator repeaters Wiper controls
11 8-121 Changing a wiper blade 236
Door mirrors
86
Doors
102-104
- opening/closing
- central locking- emergency control
Alarm 96-99
Electric windows 10 0-101
Fuel tank 1
06-107
Misfuel prevention 108
Accessories
242-243


Hill
start assist 181
Braking assistanc e 152-15 3
Tr ajectory control 153 -154
Tyre pressures 208, 256 B
oot 105
Te m p o r a ry puncture repair kit 202-208
Changing a wheel 209 -215
- tools- removing / refittingSnow chains 216

Chan
ging bulbs 221-223
- rear lamps
- 3D rear lamps
- 3rd brake lam
p
- number plate lamps

Rear parking sensors 186 -187
T
owbar 239-240
To w i ng 237-238