Page 151 of 368
149
6
Safety
When the vehicle is moving
If this warning lamp comes
on continuously it indicates a
malfunction of the anti-lock braking
system which could result in a loss of
control of the vehicle on braking.
The two warning lamps comes on at the
same time and the two warnings are
displayed alternately in the instrument
panel screen.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer's recommendations.
The vehicle retains normal braking.
Drive carefully at moderate speed and contact
a CITROËN dealer or qualified workshop as
soon as possible. If these two warning lamps come on, linked
with the warnings on the instrument panel
screen, they indicate a malfunction of the
electronic brake force distribution which could
result in a loss of control of the vehicle on
braking.
You must stop as soon as it is safe to do so.
Contact a CITROËN dealer or a qualified
workshop.
Page 152 of 368
150
Safety
Associated systems which guarantee the directional stability of the vehicle within the limits of the laws of physics:
- traction control (TCL),
- active stability control (ASC).
Traction control and active stability control
Traction control optimises traction to prevent
wheel spin, by acting on the brakes of the
driving wheels and on the engine.
Active stability control acts on the brake of one
or more wheels and on the engine to keep the
vehicle on the trajectory required by the driver.
Activation
These systems are activated automatically
each time the vehicle is started.
The illumination of this warning lamp
in the instrument panel indicates
that the ASC and TCL systems are
deactivated.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, ...), it may be advisable to deactivate
the ASC system, so that the wheels can move
freely and regain grip.
This is indicated by flashing of this
symbol on the instrument panel
screen.
Trajectory control systems
)
Press this button, located to the right of the
steering wheel, until the symbol appears in
the instrument panel screen.
Operation
They operate when the vehicle speed is higher
than 10 mph (15 km/h).
They come into operation in the event of a grip
or trajectory problem.
Page 180 of 368
178
Practical information
1. Sealing
Repair procedure
Avoid removing any foreign bodies
which have penetrated into the tyre.
)
Stop the vehicle in as safe a location as
possible and on a level and stable sur face.
)
Apply the parking brake.
)
Place the gear lever in position R
for
vehicle with a manual gearbox, or in
position P
for vehicles fitted with a CVT
gearbox.
)
Switch off the ignition.
)
Indicate on the speed restriction sticker
provided, the wheel to be repaired, then fix
it to the steering wheel as a reminder that a
wheel is in temporary use.
)
Remove the valve cap for the tyre to be
repaired.
)
Remove the valve core using the tool
provided, and store in in a clean place.
)
Connect the injection pipe to the valve of
the tyre to be repaired.
)
Shake the sealant cartridge, remove the
cap and screw on the injection pipe.
Page 185 of 368
183
7
Practical information
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: if possible, park the vehicle
on level, stable and non-slippery
ground.
Apply the parking brake, switch off the
ignition and engage first gear to lock
the wheels.
If necessary, place a chock under the
wheel diagonally opposite the wheel to
be changed.
Never go underneath a vehicle raised
using a jack; use a stand.
List of operations
)
If your vehicle is equipped with security
wheel bolts (equipment available as an
accessory) fit the security socket 5
on the
wheelbrace 1
to slacken the security bolt.
)
Slacken the other bolts using the
wheelbrace 1
only.
Page 189 of 368
187
7
Practical information
For more information on snow chains,
contact a CITROËN dealer or a
qualified workshop.
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when
braking.
Advice on installation
)
If you have to fit the chains during a
journey, stop the vehicle on a flat sur face
on the side of the road.
)
Apply the parking brake and position any
wheel chocks to prevent movement of your
vehicle.
)
Fit the chains following the instructions
provided by the manufacturer.
)
Move off gently and drive for a few
moments, without exceeding 30 mph
(50 km/h).
)
Stop your vehicle and check that the snow
chains are correctly tightened.
The snow chains must be fitted only
to the front wheels. They must never
be fitted to "space-saver" type spare
wheels.
Take account of the legislation in force
in your country on the use of snow
chains and the maximum running speed
authorised.
Avoid driving on roads that have been
cleared of snow, to avoid damaging
your vehicle's tyres and the road
sur face. It is recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face. If
your vehicle is fitted with alloy wheels,
check that no part of the chain or its
fixings is in contact with the wheel rim.
Use only chains designed for fitment to the type
of road wheels on your vehicle:
Original equipment
tyre size Maximum link size
215/70 R16
12 mm
225/55 R18
Page 194 of 368
192
Practical information
1.
Third brake lamp (LEDs).
2.
Number plate lamps (W5W- 5W).
3.
Rear foglamp (W21W-21W)
.
4.
Reversing lamp ( W16W-16W ).
5.
Direction indicators ( W Y21W-21W ).
6.
Sidelamps / brake lamps (W21- 5W).
Rear lamps
These bulbs are changed from outside the
boot.
)
Open the boot.
)
Remove the two fixing screws.
)
Unclip the lamp unit carefully extract it
pulling it towards the rear.
)
Turn the bulb holder a quarter of a turn to
the left and pull it out.
)
Pull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.
Take care to align the pins on the lamp unit with
the locations on the bodywork.
Changing sidelamp / brake
lamp (6), direction indicator (5),
and foglamp (3) bulbs
)
Open the boot.
)
Insert a screwdriver into the aperture of the
cover and lever it open.
)
Turn the bulb holder a quarter of a turn to
the left.
)
Pull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.
You can also contact a CITROËN dealer or a
qualified workshop for the replacement of these
bulbs.
Changing reversing lamp
bulbs (4)
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specification and
colour.
Page 195 of 368
193
7
Practical information
Changing number plate lamp
bulbs (2)
)
Push the lens to the left and then down.
)
Turn the bulb holder a quarter turn to the
left and pull it out.
)
Remove the bulb and change it.
To refit, carry out these operations in reverse
order and press on the lens to clip it in place.
Third brake lamp (light emitting
diodes - LEDs) (1)
Contact a CITROËN dealer or qualified
workshop for the replacement of this type of
lamp.
Page 197 of 368
195
7
Practical information
Dashboard fuses
The fuses are located in the lower dashboard
behind the glove box.
Access to the fuses
)
Open the glove box.
)
Push the two opening guides towards the
middle to by-pass the first catch.
)
Hold the glove box lid and tilt it downwards.
Fuse N°
Rating
Functions
1*
30 A
Cabin fan.
2
15 A
Brake lamps, third brake lamp.
3
10 A
Rear foglamps.
4
30 A
Windscreen wiper, screenwash.
6
20 A
Central locking, electric door mirrors.
7
15 A
Audio equipment, telematics, USB unit, Bluetooth system.
8
7.5 A
Remote control key, air conditioning control unit, instrument
panel, electric windows, rain and sunshine sensors, alarm,
switch panel, steering mounted controls.
9
15 A
Instrument panel and cabin lighting.
10
15 A
Hazard warning lamps
11
15 A
Rear wiper.
12
7.5 A
Instrument panel, multifunction screen, parking sensors,
heated seats, heated rear screen, electric blind, automatic
headlamp adjustment.
13
15 A
Cigarette lighter, accessory socket.
15
20 A
Electric blind.
16
10 A
Door mirrors, audio equipment.
