2014 Citroen C3 RHD bulb

.
.
direction indicators 99
Hazard warning lamps
9
9
Horn


10 0
Emergency or assistance call

1
00
Tyre under-inflation detection

1
01
Braking assistance systems

1
05
Trajectory control systems

1
06
Front seat belts

1
07
air

bags
1
09
Safety
Parking brake 1 13
6-speed manual gearbox
1
13
Electronic gearbox
1

14
au

tomatic gearbox
1
18
Gear ef ficiency indicator

1
22
Stop & Start

1
23
Hill start assist

1
26
Speed limiter

1
27
Cruise control

1
29
Rear parking sensors
1

31
Reversing camera
1

33
driving
eMyWay 19 7
Audio system
2
51
audio and telematics
al

phabetical index
Bonnet 13 5
Running out of fuel (
di
esel)
1
36
Petrol engines

1
37
di

esel engines
1
38
Checking levels

1
39
Checks
14

2
Checks
Temporary puncture repair kit 144
Changing a wheel
1
49
Snow chains

1
56
Changing a bulb

1
57
Changing a fuse
1

64
Battery
1

71
Energy economy mode

1
74
Changing a wiper blade

1
75
Towing the vehicle

1
76
Towing a trailer

1
78
a

udio pre-equipment
1
80
Accessories
1

82
Practical information Technical data
Petrol engines 1
84
Petrol weights
1
85
LPG engines

1
87
LPG weights

1
88
di

esel engines
1
89
Diesel weights

1
91
di

mensions

193
Identification markings
1

94
Emergency or assistance

1
95
Visual search
Contents

85
Rear parcel shelf
To remove the shelf:
F u nhook the two cords,
F

r
aise the shelf slightly, then unclip it on
each side.
Hooks
The hooks can be used to hold shopping bags.
Storage box
F Raise the boot carpet by pulling the strap upwards to gain access to the storage box.
This has areas for storing a temporary puncture
repair kit, a box of spare bulbs, a first aid kit,
two warning triangles, ...
F

r
efit the boot floor carpet by folding it
slightly in the middle.
6
Fittings

157
Changing a bulb
1. Direction indicators (PY21W amber).
2. Sidelamps (W5W).
3.
M

ain beam headlamps (H1-55W).
4.
D

ipped beam headlamps (H7-55W).
5.
L

ED daytime running lamps.
6.
F

ront foglamps (PSX24W).
Front lampsThe headlamps are fitted with
polycarbonate glass with a protective
coating:
F
d
o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u
se a sponge and soapy water or a
pH neutral product,
F

w
hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals. Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D
o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
11
Practical information

158
Changing direction indicator
bulbs
F Turn the bulb holder a quarter of a turn and extract it.
F

P
ull out the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Changing dipped beam headlamp
bulbs
F Remove the protective cover by pulling the tab.
F
d
i
sconnect the bulb connector.
F

S
pread the springs to release the bulb.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Rapid flashing of the direction indicator
warning lamp (right or left) indicates the
failure of a bulb on that side.
When refitting, close the protective
cover carefully to preserve the sealing
of the headlamp.am
ber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifications
and colour.
Practical information

159
Changing main beam headlamp
bulbs
F Remove the protective cover by pulling on the tab.
F
d
i
sconnect the bulb connector.
F

S
pread the springs to release the bulb.
F

R
emove the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Changing sidelamp bulbs
F Remove the protective cover by pulling on the tab.
F

P
ull the bulb holder pressing on the tabs on
both sides.
F

P
ull the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
11
Practical information

160
Changing integrated direction
indicator side repeaters
F Insert a screwdriver towards the centre of the repeater between the repeater and the
base of the door mirror.
F

T
ilt the screwdriver to extract the repeater
and remove it.
F
d
i
sconnect the repeater connector.
F

R
eplace the module.
To refit, carry out these operations in reverse
o r d e r.
Contact a CITR
oËn

dealer or
a qualified workshop to obtain a
replacement side repeater module.
Changing front foglamp bulbs
F access to the front foglamp is through the aperture below the bumper.
F
d
i
sconnect the black bulb holder
connector, by pressing on the tab at the
top.
F

R
emove the bulb-holder by pressing on the
2 clips (at the top and the bottom).
F

R
eplace the module.
To refit, carry out these operations in reverse
o r d e r. To obtain a replacement module,
contact your CITR
oËn

dealer or a
qualified workshop.
If you experience any difficulty in
replacing bulbs, contact your CITR
oËn


dealer or a qualified workshop.
Practical information

161
Rear lamps
1. Brake / sidelamps (P21/5W).
2. Direction indicators (PY21W amber) .
3.
F

oglamp, right-hand side (PR21W red)
R

eversing lamp, left-hand side (P21W).Changing bulbs
These four bulbs are changed from inside the
boot: F

s
pread the four tabs and remove the bulb
h o l d e r,
F

t
urn the bulb a quarter of a turn and change
it.
To refit, carry out these operations in reverse
o r d e r.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
F

o
pen the boot,
F

r
emove the access flap from the
corresponding side trim panel,
F

u
nscrew the butter fly nut securing the lamp
unit,
F

u
nclip the lamp unit connector,
F

e
xtract the lamp unit carefully pulling in its
middle towards the outside,
am

ber or red bulbs, such as those
for the direction indicators and rear
foglamp, must be replaced by bulbs of
the same rating and colour.
The lamps on the tailgate are dummy
units. They are there for aesthetic
purposes only.
11
Practical information

162
Changing the number plate lamp
bulbs (W5W)
F Insert a thin screwdriver into one of the outer holes of the lens.
F

P
ush it outwards to unclip.
F

R
emove the lens.
F

P
ull the bulb out and change it.
Third brake lamp
(4 W5W bulbs)
F open the boot.
F R emove the plugs A on the inner panel.
F

P
ush on the centre of the lamp using
two
screwdrivers to lever it outwards.
F
d
i
sconnect the connector and if necessary
the screenwash pipe from the lamp.
F

T
urn the bulb holder for the faulty bulb a
quarter of a turn.
F

P
ull out the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Practical information