2014 Citroen C3 PICASSO RHD Owner's Manual

135
Programming
F Turn dial 1 to the "CRUISE" position:
the cruise control mode is selected
but is not switched on (PAUSE).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results in
flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the speed.
Return to normal driving
F Turn dial 1 to the "0" position: the cruise control mode is
deselected. The display returns to the distance recorder.
Operating fault
In the event of a cruise control malfunction,
the speed is cleared resulting in flashing of
the


dashes.
Have it checked by a CITR
oËn

dealer or a
qualified workshop.
F

S

et the programmed speed by
accelerating to the required speed,
then press button 2 or 3 (e.g.: 70 mph
(110 km/h)).
F

S

witch off the cruise control by pressing button 4 :
this is confirmed in the screen (P
aU

SE).
F

S

witch the cruise control back on by pressing button 4 again.
You can then change the programmed speed using buttons 2 and 3
:
-

b

y + or - 1 mph (km/h) = short press,
-

b

y + or - 5 mph (km/h) = long press,
-

i

n steps of + or - 5 mph (km/h) = maintained press. When the cruise control is switched on,
be careful if you maintain the pressure
on one of the programmed speed
changing buttons: this may result in a
very rapid change in the speed of your
vehicle.
do n

ot use the cruise control on
slippery roads or in heavy traffic.
on a s

teep descent, the cruise control
will not be able to prevent the vehicle
from exceeding the programmed speed.
To avoid any risk of jamming of the
pedals:
-

e
nsure that the mat is secured
c o r r e c t l y,
-

n
ever fit one mat on top of another.
9
Driving

136
Rear parking sensorsSystem comprising four proximity sensors, located in the rear bumper.
This detects obstacles (person, vehicle, tree,
gate, etc.) behind the vehicle. However, it
cannot detect obstacles located just below
the bumper.
Activation
The system is activated as soon as reverse
gear is engaged, accompanied by an audible
signal. The proximity information is given by:
-
a
n audible signal, which becomes more
rapid as the vehicle approaches the
obstacle,
-

a g
raphic in the multifunction screen, with
blocks which become increasingly closer to
the vehicle (depending on version).
Detection zoneWhen the distance between the rear of the vehicle
and the obstacle is less than thirty centimetres,
the audible signal becomes continuous and the
"
da

nger" symbol appears in the multifunction
screen.
On completion of the manoeuvre, when you exit
reverse gear, the system becomes inactive.
An object, such as a stake, a roadworks
cone or any other similar object may
be detected at the beginning of the
manoeuvre, but may no longer be detected
when the vehicle comes close to it. The parking sensors system cannot in
any circumstances take the place of
vigilance on the part of the driver.
driving

137
DeactivationReactivation
With the engine running, press button A to
deactivate the system permanently. The
indicator lamp in the button comes on.
The system will be deactivated
automatically when towing a trailer or
when a bicycle carrier is fitted (vehicle
fitted with a towbar or bicycle carrier
recommended by CITR
oËn)

.In bad or wintry weather, ensure that
the sensors are not covered with mud,
frost or snow.
Press button A again to reactivate the system.
The indicator lamp in the button goes off.
If there is an operating fault, when reverse gear
is engaged, the service warning lamp comes
on, accompanied by an audible signal (short
beep) and a message in the multifunction
screen.
9
Driving

138
Reversing camera
a reversing camera is activated automatically
w hen reverse gear is engaged.
The colour image is provided in the navigation
screen. The space between the blue lines represents
the width of your vehicle except for the door
mirrors.
The blue lines represent the general direction
of the vehicle.
The red line represents a distance of about
30 cm beyond the edge of your vehicle's
rear bumper. The audible signal becomes
continuous from this limit.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper.
Clean the reversing camera regularly
using a soft, dry cloth.
The reversing camera cannot in any
circumstances be a substitute for
vigilance on the part of the driver.
driving

139
ToTaL & CITRoËn
Partners in performance and
protecting the environment
Innovation in the search for
performance
For over 40 year, the TOTAL Research and development departments have developed for
CITR
oËn, l

ubricants to match the latest technical
innovations on CITR
oËn

vehicles, both for
competition and for everyday motoring.
For you, this is an assurance that you will obtain of the
best performance for your engine.
Optimum protection
for your engine
by having your CITRoËn vehicle
serviced with TOTAL lubricants, you are
contributing towards improving the life
and per formances of your engine, while
also protecting the environment.
prefers
10
Checks

140
bonnet
F Push the exterior safety catch B to the left and raise the bonnet.
F

U
nclip the stay C from its housing.
F

F
ix the stay in the notch to hold the bonnet
open.
Closing
F Take the stay out of the support notch.
F C lip the stay in its housing.
F

L
ower the bonnet and release it at the end
of its travel.
F

P
ull on the bonnet to check that it is
secured correctly.
F
o
p

en the front left door.
F

P

ull the interior bonnet release lever A ,
located at the bottom of the door aperture.
Opening
before doing anything under the
bonnet, switch off the Stop & Start
system to avoid any risk of injury
resulting from an automatic change to
S T
a
R
T m o d e .
The location of the interior bonnet
release lever prevents opening of the
bonnet while the front left door is closed. Do not open the bonnet in high winds.
When the engine is hot, handle the
exterior safety catch and the bonnet
stay with care (risk of burns).
Checks

141
Running out of fuel
(
die
sel)
F Fill the fuel tank with at least five litres of die
sel.
F
o
p
en the bonnet.
F
d
e
pending on version, unclip the cover to
gain access to the priming pump.
F

S
queeze and release the priming pump
until resistance is felt (could be from the
first application) and fuel appears in the
transparent pipe with the green connector.
F
o
p
erate the starter until the engine starts.
F
d
e
pending on version, put the cover back
in position and clip it in place.
F

C
lose the bonnet.If the engine does not start at the first
attempt, do not try again.
op

erate the priming pump again, then
the starter.
If your vehicle is fitted with an HDI engine,
the fuel system must be primed if you run out
of fuel.
This system consists of a priming pump and a
transparent pipe under the bonnet.
10
Checks

142
Petrol engines
1. Screenwash fluid reservoir.
2. Coolant header tank.
3.


a
i
r f i l t e r.
4.


b
r
ake fluid reservoir.
5.
bat

tery.
6.
F

usebox.
7.
E

ngine oil dipstick.
8.
E

ngine oil filler cap.
To avoid damaging the electrical units,
the use of a high pressure washer
in the engine compartment is strictly
prohibited .
Checks