2014 BMW ACTIVE HYBRID 7 service

Should it prove impossible to avoid mounting
the tow bar at an offset angle, please observe
the following:▷Maneuvering capability is limited going
around corners.▷The tow bar will generate lateral forces if it
is secured with an offset.
Tow rope
When starting to tow the vehicle, make sure
that the tow rope is taut.
To avoid jerking and the associated stresses
on the vehicle components when towing, al‐
ways use nylon ropes or nylon straps.
Tow fitting
The screw-in tow fitting should always be car‐
ried in the vehicle.
The tow fitting can be screwed in at the front
or rear of the BMW.
The tow fitting is located in the container on
the inside of the trunk lid.
Tow fitting, information on use
▷Use only the tow fitting provided with
the vehicle and screw it all the way in.▷Use the tow fitting for towing on paved
roads only.▷Use tow fitting located in the front only for
positioning the vehicle.▷Avoid lateral loading of the tow fitting, e.g.,
do not lift the vehicle by the tow fitting.
Otherwise, damage to the tow fitting and the
vehicle can occur.◀
Screw thread for tow fitting
Push out the cover by pressing on the top
edge.
Tow-starting
Note:
Do not tow-start the vehicle.
Tow-starting the engine is not possible due to
the Steptronic transmission.
Have the cause of the starting problems fixed.
Safety of the hybrid system Hybrid system workYour vehicle's hybrid system is a self-con‐
tained system. Safety is ensured as long as no
work is performed on the technical compo‐
nents.
Thus, have work on the vehicle, for instance
retrofitting accessories, performed by the
service center or a workshop that works ac‐
cording to BMW specifications with appropri‐
ately trained personnel.
Seite 232MobilityBreakdown assistance232
Online Edition for Part no. 01 40 2 956 056 - X/14

Maintenance and repairs
Have maintenance and repair work per‐
formed only by a service center or a workshop
that works according to BMW specifications
with appropriately trained personnel. Other‐
wise, there is the risk of fatal injury from elec‐
trocution due to the high-voltage system's
high voltage.◀
Hybrid system: contact with water The hybrid system is typically safe even in the
following example situations:▷Water in the footwell, for instance after a
rainstorm when sunroof was kept open.▷Vehicle is in water but only up to the al‐
lowed height.▷Liquid eslides in the cargo area.
In these cases there is no risk of injury from
electrocution. Other damage to the vehicle is
possible.
Hybrid system: automatic
deactivation
If an accident occurs, the hybrid system is
switched off automatically to prevent risk of
danger to occupants and other traffic.
Read the information on What to do after an
accident, refer to page 233.
What to do after an accident Hints After an accident
After an accident, do not touch any high-
voltage components such as orange colored
high-voltage cables or parts that are in contact
with exposed high-voltage cables. Otherwise,
there is the risk of fatal injury from electrocu‐
tion due to the system's high voltage.◀
Esliding fluids
Do not touch any fluids esliding from the
high-voltage battery, or the skin can sustain
chemical burns.◀
General information
If you are involved in an accident with your ve‐
hicle, compliance with the following additional
safety precautions is required with regard to
the high-voltage system:▷Secure the crash site.▷Immediately notify rescue forces, police, or
firefighters of the fact that your vehicle is
equipped with a high-voltage system.▷Engage selector lever position P, apply the
parking brake, and reel off the ignition or
deactivate drive readiness.▷Lock the vehicle after exiting.▷Do not inhale any gases esliding from the
high-voltage battery; if needed, maintain a
safe distance from the vehicle.Seite 233Breakdown assistanceMobility233
Online Edition for Part no. 01 40 2 956 056 - X/14

In this way, the ignition remains switched
on, and a Check-Control message is dis‐
played.
Do not turn off the ignition in the car
wash
Do not turn off the ignition in the car wash;
otherwise, selector lever position P is en‐
gaged and damages can result.◀
The vehicle cannot be locked from the outside
when in selector lever position N. A signal
sounds when an attempt is made to lock the
vehicle.
For activation of drive readiness:
1.Depress the brake pedal.2.Press the Start/Stop button.
Pressing the Start/Stop button without step‐
ping on the brake turns the ignition off.
Selector lever positionSelector lever position P is engaged automati‐
cally:
▷When the ignition is switched off.▷After approx. 15 minutes.
Headlights
▷Do not rub dry and do not use abrasive or
acidic cleansers.▷Soak areas that have been dirtied e. g.,
from insects, with shampoo and wash off
with water.▷Thaw ice with de-icing spray; do not use an
ice scraper.
After washing the vehicle
After washing the vehicle, apply the brakes
briefly to dry them; otherwise, braking action
can be reduced and corrosion of the brake
discs can occur.
Completely remove all residues on the win‐
dows, to minimize loss of visibility due to
smearing and to reduce wiper noises and
wiper blade wear.
Vehicle care
Car care productsBMW recommends using care and cleaning
products from BMW, since these have been
tested and approved.
Car care and cleaning products
Follow the instructions on the container.
When cleaning the interior, open the doors or
windows.
Only use products intended for cleaning vehi‐ cles.
Cleansers can contain substances that are
dangerous and harmful to your health.◀
Vehicle paint Regular care contributes to driving safety and
value retention. Environmental influences in
areas with elevated air pollution or natural con‐
taminants, such as tree resin or pollen can af‐
fect the vehicle's paintwork. Tailor the fre‐
quency and extent of your car care to these
influences.
Aggressive substances such as spilled fuel, oil,
grease or bird droppings, must be removed im‐
mediately to prevent the finish from being al‐
tered or discolored.
Only use respectively approved cleaning and
care products for vehicles with matte finish.
Suitable care products for matte finishes are
available from the service center.
Leather care Remove dust from the leather often, using a
cloth or vacuum cleaner.
Otherwise, particles of dust and road grime
chafe in pores and folds, and lead to increased
wear and premature degradation of the leather
surface.
To guard against discoloration, such as from
clothing, provide leather care roughly every
two months.Seite 235CareMobility235
Online Edition for Part no. 01 40 2 956 056 - X/14

Clean light-colored leather more frequently be‐
cause soiling on such surfaces is substantially
more visible.
Use leather care products; otherwise, dirt and
grease will gradually break down the protective
layer of the leather surface.
Suitable care products are available from the
service center.
Upholstery material care Vacuum regularly with a vacuum cleaner.
If upholstery is very dirty, e.g., with beverage
stains, use a soft sponge or microfiber cloth
with a suitable interior cleaner.
Clean the upholstery down to the seams using
large sweeping motions. Avoid rubbing the
material vigorously.
Damage from Velcro® fasteners
Open Velcro® fasteners on pants or
other articles of clothing can damage the seat
covers. Ensure that any Velcro® fasteners are
closed.◀
Caring for special components
Light-alloy wheels When cleaning the vehicle, use only neutral
wheel cleaners having a pH value from 5 to 9.
Do not use abrasive cleaning agents or steam
jets above 140 ℉/60 ℃. Follow the manufac‐
turer's instructions.
Aggressive, acidic or alkaline cleaning agents
can destroy the protective layer of adjacent
components, such as the brake disk.
Chrome surfaces Carefully clean components such as the radia‐
tor grille or door handles with an ample supply of water, possibly with shampoo added, partic‐
ularly when they have been exposed to road
salt.Rubber components
Aside from water, treat only with rubber
cleansers.
When cleaning rubber seals, do not use any
silicon-containing car care products in order to
avoid damage or noises.
Fine wood partsClean fine wood facing and fine wood compo‐
nents only with a moist rag. Then dry with a
soft cloth.
Plastic components
These include:▷Imitation leather surfaces.▷Roofliner.▷Lamp lenses.▷Instrument cluster cover.▷Matt black spray-coated components.▷Painted parts in the interior.
Clean with a microfiber cloth.
Dampen cloth lightly with water.
Do not soak the roofliner.
No cleansers that contain alcohol or sol‐
vents
Do not use cleansers that contain alcohol or
solvents, such as lacquer thinners, heavy-duty
grease removers, fuel, or such; this could lead
to surface damage.◀
Safety belts
Dirty belt straps impede the reeling action and
thus have a negative impact on safety.
Chemical cleaning
Do not clean chemically; this can destroy
the webbing.◀
Use only a mild soapy solution, with the safety
belts clipped into their buckles.
Do not allow the reels to retract the safety
belts until they are dry.
Seite 236MobilityCare236
Online Edition for Part no. 01 40 2 956 056 - X/14

Carpets and floor matsNo objects in the area around the pedals
Keep floor mats, carpets, and any other
objects out of the pedal area; otherwise, the
function of the pedals could be impeded while driving and create the risk of an accident.
Do not place additional floor mats over existing
mats or other objects.
Only use floor mats that have been approved
for the vehicle and can be properly attached to
floor.
Ensure that the floor mats are securely fas‐
tened again after they were removed for clean‐
ing, e.g.◀
Floor mats can be removed from the car's inte‐
rior for cleaning.
If the floor carpets are very dirty, clean with a microfiber cloth and water or a textile cleaner.
To prevent matting of the carpet, rub back and
forth in the direction of travel only.
Sensors/cameras
To clean sensors and cameras, use a cloth
moistened with a small amount of glass
cleaner.
Displays/monitors Cleaning displays and screens
Do not use any chemical or household
cleaning agents; otherwise, surfaces can be af‐
fected.◀
Keeping out moisture
Keep all fluids and moisture away from
the unit; otherwise, electrical components can
be damaged.◀
Avoid pressure
Avoid pressing too hard when cleaning
and do not use abrasive materials; otherwise,
damage can result.◀
Clean with a clean, antistatic microfiber cloth.Long-term For idle phases that last several weeks, park
the vehicle with a fully charged battery if possi‐
ble. Your service center can advise you on
what to consider when storing the vehicle for
longer than six weeks.
Do not allow the vehicle to sit idle for ex‐
tended periods with a low charging state
Before storing the vehicle for an extended pe‐
riod, check the battery charge indicator to en‐
sure that the high-voltage battery is fully
charged. If necessary, charge the high-voltage
battery by driving the vehicle. Check the
charge level regularly, and if needed recharge
the high-voltage battery by driving the vehicle.
Don't allow battery charge status to drop too
low - it will damage the battery.◀
Note Follow the instructions for discharging thehigh-voltage battery, refer to page 187.Seite 237CareMobility237
Online Edition for Part no. 01 40 2 956 056 - X/14

Technical dataVehicle features and options
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are notnecessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems.
Note
The technical data and specifications in this
Owner's Manual are used as guidance values.
The vehicle-specific data can deviate from this,
for example, due to the selected special equip‐
ment, country version or country-specific
measurement method. Detailed values can befound in the approval documents, on informa‐
tion signs on the vehicle or can be obtained
from the service center.
The information in the vehicle documents al‐
ways has priority.
Dimensions
Note
The dimensions can vary depending on the
model version, equipment or country-specific
measurement method.
The specified heights do not take into account
attached parts, for example, a roof antenna,roof racks or spoiler. The heights can deviate,
for example, due to the selected special equip‐
ment, tires, load and chassis version. ActiveHybrid 7Width with mirrorsinches/mm84.3/2,142Width without mirrorsinches/mm74.9/1,902Height L-modelsinches/mm58.3/1,481Length L-modelsinches/mm205.5/5,220Wheelbase L-modelsinches/mm126.4/3,210Smallest turning radius diam. L-modelsft/m41.7/12.7Seite 240ReferenceTechnical data240
Online Edition for Part no. 01 40 2 956 056 - X/14

Coasting 78
Combination reel, refer to Turn signals 83
Combination reel, refer to Wiper system 84
Combustion engine, start‐ ing 76
COMFORT+ program, Driving Dynamics Control 142
Comfort Access 45
COMFORT program, Driving Dynamics Control 142
Computer 101
Condensation on win‐ dows 166
Condensation under the vehi‐ cle 190
Condition Based Service CBS 219
Confirmation signal 49
ConnectedDrive, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
ConnectedDrive Services
Contact with water, hybrid system 233
Continued driving with a flat tire 116 , 119
Control Display 18
Control Display, settings 104
Controller 18
Control systems, driving sta‐ bility 138
Convenient opening with the remote control 39
Coolant 217
Coolant level 217
Coolant temperature 97
Cooling function 167
Cooling, maximum 167
Cooling system 217
Corrosion on brake discs 190
Cosmetic mirror 175
Cruise control 151 Cruise control, active with
Stop & Go 144
Cruise Control, refer to Active Cruise Control 144
Cruising range 98
Cupholder 181
Curb weight 241
D
Damage, tires 208
Damping control, dy‐ namic 140
Data, technical 240
Date 98
Daytime running lights 108
Deactivating drive readi‐ ness 77
Defrosting, refer to Windows, defrosting 166
Dehumidifying, air 167
Deleting personal data 24
Deletion of personal data 24
Departure time, parked-car ventilation 171
Destination distance 102
Digital clock 98
Dimensions 240
Dimmable exterior mirrors 68
Dimmable interior rearview mirror 69
Direction indicator, refer to Turn signals 83
Display, electronic, instru‐ ment cluster 90
Display in windshield 105
Display lighting, refer to In‐ strument lighting 110
Displays, cleaning 237
Displays, hybrid system 91
Disposal, coolant 218
Disposal, vehicle battery 227
Distance control, refer to PDC 153
Distance to destination 102 Divided screen view, split
screen 23
Door lock 41
Door lock, refer to Remote control 36
Doors, Automatic Soft Clos‐ ing 42
DRIVE, Driving with combus‐ tion engine 79
Drive-off assistant 138
Drive-off assistant, refer to DSC 138
Driver assistance, refer to In‐ telligent Safety 120
Drive readiness in detail 76
Drive readiness states 75
Driving Assistant, refer to In‐ telligent Safety 120
Driving Dynamics Con‐ trol 140
Driving instructions, break- in 186
Driving instructions, hybrid system 186
Driving mode 140
Driving notes, general 188
Driving stability control sys‐ tems 138
Driving tips 188
Driving with combustion en‐ gine, DRIVE 79
DSC Dynamic Stability Con‐ trol 138
DTC Dynamic Traction Con‐ trol 139
Dynamic Damping Con‐ trol 140
Dynamic Stability Control DSC 138
Dynamic Traction Control DTC 139
E
eBOOST, assistance for the combustion engine 79 Seite 244ReferenceEverything from A to Z244
Online Edition for Part no. 01 40 2 956 056 - X/14

ECO PRO 195
ECO PRO, bonus range 196
ECO PRO display 195
ECO PRO driving mode 195
ECO PRO mode 195
ECO PRO Tip - driving in‐ struction 197
eDRIVE, electric driving 78
Electric drive readiness, Si‐ lent Start 76
Electric driving, eDRIVE 78
Electronic displays, instru‐ ment cluster 90
Electronic oil measure‐ ment 214
Electronic Stability Program ESP, refer to DSC 138
Emergency detection, remote control 37
Emergency release, fuel filler flap 200
Emergency release, parking brake 82
Emergency Request 228
Emergency service, refer to Roadside Assistance 229
Emergency start function, en‐ gine start 37
Emergency unlocking, trans‐ mission lock 89
Emergency unlocking, trunk lid 45
Energy recovery, CHARGE 79
Engine, automatic off 77
Engine compartment 212
Engine compartment, work‐ ing in 212
Engine coolant 217
Engine oil 214
Engine oil, adding 215
Engine oil additives 215
Engine oil change 216
Engine oil filler neck 215
Engine oil temperature 97 Engine oil types, alterna‐
tive 216
Engine oil types, ap‐ proved 216
Engine start during malfunc‐ tion 37
Engine start, jump-start‐ ing 229
Engine temperature 97
Entering/exiting vehicle, as‐ sistance, steering wheel 70
Entering a car wash 234
Equipment, interior 173
Error displays, see Check Control 93
ESP Electronic Stability Pro‐ gram, refer to DSC 138
Exchanging wheels/tires 209
Exhaust system 188
Exterior mirror, automatic dimming feature 68
Exterior mirrors 67
External start 229
External temperature dis‐ play 97
External temperature warn‐ ing 97
Eyes for securing cargo 192
F
Failure message, see Check Control 93
False alarm, refer to Uninten‐ tional alarm 51
Fan, refer to Air flow 166
Filler neck for engine oil 215
Fine wood, care 236
First aid kit 229
Fitting for towing, see tow fit‐ ting 232
Flat tire, changing wheels 225
Flat Tire Monitor FTM 115
Flat tire, Tire Pressure Moni‐ tor TPM 117 Flat tire, warning
lamp 116, 118
Flooding 189
Floor carpet, care 237
Floor mats, care 237
Fold-out position, wiper 86
Foot brake 189
Front airbags 112
Front-end collision warning with braking function 124
Front-end collision warning with City Braking func‐
tion 121
Front fog lights 110
Front fog lights, bulb replace‐ ment 224
Front passenger seat, adjust‐ ing 58
front-seat passenger airbags, automatic deactivation 114
Front-seat passenger airbags, indicator lamp 114
Front seats 56
Front turn signals, refer to Light-emitting diodes,
LEDs 223
FTM Flat Tire Monitor 115
Fuel 202
Fuel consumption, refer to Average fuel consump‐
tion 102
Fuel filler flap 200
Fuel gauge 97
Fuel lid 200
Fuel quality 202
Fuel recommendation 202
Fuel, tank capacity 241
Functions, hybrid system 31
Fuse 227
G
Garage door opener, refer to Universal Integrated Remote
Control 173
Gasoline 202 Seite 245Everything from A to ZReference245
Online Edition for Part no. 01 40 2 956 056 - X/14