2014 BMW ACTIVE HYBRID 3 sensor

HintsSufficient ventilation
When remaining in the vehicle for an ex‐
tended period of time, ensure sufficient exter‐
nal ventilation. Do not continuously use recir‐
culated-air mode; otherwise the air quality in
the interior continuously worsens.◀
Climate control functions in detail
Temperature Turn the ring to set the desired
temperature.
The automatic climate control reaches this
temperature as quickly as possible, if needed
by increasing the cooling or heating output,
and then keeps it constant.
Do not rapidly switch between different tem‐
perature settings. Otherwise, the automatic cli‐
mate control will not have sufficient time to ad‐
just the set temperature.
AUTO program Press button.
Air flow, air distribution and tempera‐
ture are controlled automatically.
Depending on the selected temperature,
AUTO intensity program and outside influen‐ ces, the air is directed to the windshield, side
windows, upper body, and into the footwell.
The cooling function, refer to page 151, is
switched on automatically with the AUTO pro‐
gram.
At the same time, a condensation sensor con‐
trols the program so as to prevent window
condensation as much as possible.Intensity of the AUTO program
With the AUTO program activated, the auto‐
matic intensity control can be changed.
Press the left or right side of the but‐
ton: decrease or increase the inten‐
sity.
The selected intensity is shown on the display
of the automatic climate control.
Maximum cooling Press button.
The system is set to the lowest tem‐
perature, optimum air flow and air circulation
mode.
Air flows out of the vents to the upper body re‐
gion. The vents need to be open for this.
The function is available above an external
temperature of approx. 32 ℉/0 ℃ and with the
engine running or when electrical drive readi‐ ness is indicated.
Adjust air flow with the program active.
Cooling function
The car's interior can be cooled with the en‐
gine running or switched off.
Press button.
The air will be cooled and dehumidi‐
fied and, depending on the temperature set‐
ting, warmed again.
Depending on the weather, the windshield and
side windows may fog up briefly when the en‐
gine is started.
The cooling function is switched on automati‐
cally with the AUTO program.
When using the automatic climate control,
condensation water, refer to page 174, devel‐
ops that exits underneath the vehicle.Seite 151Climate controlControls151
Online Edition for Part no. 01 40 2 956 725 - X/14

Automatic recirculated-air control/recirculated-air mode
You may respond to unpleasant odors or pollu‐ tants in the immediate environment by tempo‐
rarily suspending the supply of outside air. The
system then recirculates the air currently
within the vehicle.
Press button repeatedly to select an
operating mode:▷LEDs off: outside air flows in continuously.▷Left LED on, automatic recirculated-air
control: a sensor detects pollutants in the
outside air and shuts off automatically.▷Right LED on, recirculated-air mode: the
supply of outside air into the vehicle is per‐
manently blocked.
Recirculated air mode switches off automati‐
cally at low external temperatures after a cer‐
tain amount of time in order to avoid window
fogging.
If the windows are fogged over, reel off the re‐
circulated-air mode and press the AUTO but‐
ton to utilize the condensation sensor. Make
sure that air can flow to the windshield.
Sufficient ventilation
When remaining in the vehicle for an ex‐
tended period of time, ensure sufficient exter‐
nal ventilation. Do not continuously use recir‐
culated-air mode; otherwise the air quality in
the interior continuously worsens.◀
Manual air distribution Press button repeatedly to select a
program:
▷Upper body region.▷Upper body region and footwell.▷Footwell.▷Windows and footwell: driver's side only.▷Windows, upper body region and footwell:
driver's side only.If the windows are fogged over, press the
AUTO button to utilize the condensation sen‐
sor.
Air flow, manual
To manually adjust air flow turn off AUTO pro‐
gram first.
Press the left or right side of the but‐
ton: decrease or increase air flow.
The selected air flow is shown on the display of
the automatic climate control.
The air flow of the automatic climate control
may be reduced automatically to save battery
power.
Rear window defroster Press button.
The rear window defroster switches
off automatically after a certain period of time.
Defrosts windows and removes
condensation
Press button.
Ice and condensation are quickly re‐
moved from the windshield and the front side
windows.
For this purpose, point the side vents onto the
side windows as needed.
Adjust air flow with the program active.
If the windows are fogged over, you can also
reel on the cooling function or press the AUTO
button to utilize the condensation sensor.
Switching the system on/off Switch off Press the left button for the minimum
speed.Seite 152ControlsClimate control152
Online Edition for Part no. 01 40 2 956 725 - X/14

MaintenanceVehicle features and options
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems.
BMW maintenance system
The maintenance system indicates required
maintenance measures, and thereby provides
support in maintaining road safety and the op‐
erational reliability of the vehicle.
Condition Based Service
CBS
Sensors and special algorithms take into ac‐
count the driving conditions of your vehicle.
Based on this, Condition Based Service recog‐
nizes the maintenance requirements.
The system makes it possible to adapt the
amount of maintenance corresponding to your
user profile.
Detailed information on service requirements,
refer to page 88, can be displayed on the Con‐
trol Display.
For service data
Information on the required maintenance is
continuously stored in the remote control. Your service center will read out this data and
suggest the right array of service procedures for your vehicle.
Therefore, hand your service specialist the re‐
mote control with which the vehicle was driven
most recently.Storage periods
Storage periods during which the vehicle bat‐
tery was disconnected are not taken into ac‐
count.
If this occurs, have a service center update the
time-dependent maintenance procedures,
such as checking brake fluid and, if needed,
changing the engine oil and the microfilter/
activated-charcoal filter.
Service and Warranty
Information Booklet for US
models and Warranty and
Service Guide Booklet for
Canadian models
Please consult your Service and Warranty In‐
formation Booklet for US models and Warranty
and Service Guide Booklet for Canadian mod‐ els for additional information on service re‐
quirements.
Maintenance and repair should be performed
by your service center. Make sure to have reg‐
ular maintenance procedures recorded in the
vehicle's Service and Warranty Information
Booklet for US models, and in the Warranty
and Service Guide Booklet for Canadian mod‐
els. These entries are proof of regular mainte‐
nance.
Socket for OBD Onboard
Diagnosis
Note Socket for Onboard Diagnosis
The socket for onboard diagnostics may
only be used by the service center or a work‐
shop that operates in accordance with the
specifications of the vehicle manufacturer withSeite 204MobilityMaintenance204
Online Edition for Part no. 01 40 2 956 725 - X/14

CareVehicle features and optionsThis chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems.
Car washes
General information
Regularly remove foreign objects such as
leaves in the area below the windshield when
the hood is raised.
Wash your vehicle frequently, particularly in
winter. Intense soiling and road salt can dam‐
age the vehicle.
Hints Steam jets or high-pressure washers
When using steam jets or high-pressure
washers, hold them a sufficient distance away
and use a maximum temperature of
140 ℉/60 ℃.
If the vehicle has a glass sunroof, ensure that a
distance of at least 31.5 inches/80 cm is main‐
tained. Holding them too close or using exces‐
sively high pressures or temperatures can
cause damage or preliminary damage that may
then lead to long-term damage.
Follow the user's manual for the high-pressure
washer.◀
Cleaning sensors/cameras with high-
pressure washers
When using high-pressure washers, do not
spray the exterior sensors and cameras, e.g.,
Park Distance Control, for extended periods oftime and only from a distance of at least
12 in/30 cm.◀
Automatic car washes
Hints▷Give preference to cloth car washes or
those that use soft brushes in order to
avoid paint damage.▷Make sure that the wheels and tires are not
damaged by the transport mechanisms.▷Fold in the exterior mirrors; otherwise, they
may be damaged, depending on the width
of the vehicle.▷Deactivate the rain sensor, refer to
page 74, to avoid unintentional wiper acti‐
vation.▷In some cases, an unintentional alarm can
be triggered by the interior motion sensor
of the alarm system. Follow the instruc‐
tions on avoiding an unintentional alarm,
refer to page 47.
Guide rails in car washes
Avoid car washes with guide rails higher
than 4 in/10 cm; otherwise, the vehicle body
could be damaged.◀
Before driving into a car wash In order to ensure that the vehicle can roll in a
car wash, take the following steps:
1.Drive into the car wash.2.Engage selector lever position N.3.Switch the engine off.
In this way, the ignition remains switched
on, and a Check-Control message is dis‐
played.Seite 223CareMobility223
Online Edition for Part no. 01 40 2 956 725 - X/14

Carpets and floor matsNo objects in the area around the pedals
Keep floor mats, carpets, and any other
objects out of the pedal area; otherwise, the
function of the pedals could be impeded while driving and create the risk of an accident.
Do not place additional floor mats over existing
mats or other objects.
Only use floor mats that have been approved
for the vehicle and can be properly attached to
floor.
Ensure that the floor mats are securely fas‐
tened again after they were removed for clean‐
ing, e.g.◀
Floor mats can be removed from the car's inte‐
rior for cleaning.
If the floor carpets are very dirty, clean with a microfiber cloth and water or a textile cleaner.
To prevent matting of the carpet, rub back and
forth in the direction of travel only.
Sensors/cameras
To clean sensors and cameras, use a cloth
moistened with a small amount of glass
cleaner.
Displays/monitors Cleaning displays and screens
Do not use any chemical or household
cleaning agents; otherwise, surfaces can be af‐
fected.◀
Keeping out moisture
Keep all fluids and moisture away from
the unit; otherwise, electrical components can
be damaged.◀
Avoid pressure
Avoid pressing too hard when cleaning
and do not use abrasive materials; otherwise,
damage can result.◀
Clean with a clean, antistatic microfiber cloth.Long-term For idle phases that last several weeks, park
the vehicle with a fully charged battery if possi‐
ble. Your service center can advise you on
what to consider when storing the vehicle for
longer than six weeks.
Do not allow the vehicle to sit idle for ex‐
tended periods with a low charging state
Before storing the vehicle for an extended pe‐
riod, check the battery charge indicator to en‐
sure that the high-voltage battery is fully
charged. If necessary, charge the high-voltage
battery by driving the vehicle. Check the
charge level regularly, and if needed recharge
the high-voltage battery by driving the vehicle.
Don't allow battery charge status to drop too
low - it will damage the battery.◀
Note Follow the instructions for discharging thehigh-voltage battery, refer to page 171.Seite 226MobilityCare226
Online Edition for Part no. 01 40 2 956 725 - X/14

Height, vehicle 230
High-beam Assistant 99
High beams 73
High beams/low beams, refer to High-beam Assistant 99
High-voltage battery, charge indicator 81
High-voltage battery, dis‐ charge 171
Hills 173
Hill start assistant, refer to Drive-off assistant 128
Hints 6
Holder for beverages 166
Hood 199
Horn 14
Hotel function, trunk lid 42
Hot exhaust system 172
HUD Head-up Display 95
Hybrid system, adapting to the course of the road 83
Hybrid system, at a glance 31
Hybrid system, automatic de‐ activation 222
Hybrid system, contact with water 222
Hybrid system, displays 81
Hybrid system, safety 221
Hydroplaning 172
I Ice warning, see External temperature warning 87
Icy roads, see External tem‐ perature warning 87
Identification marks, tires 192
Identification number, see ve‐ hicle identification num‐
ber 10
iDrive 18
Ignition key, refer to Remote control 36
Ignition off 67
Ignition on 67 Indication of a flat
tire 106 , 109
Indicator and alarm lamps, see Check Control 83
Indicator lamp, see Check Control 83
Individual air distribution 152
Individual settings, refer to Personal Profile 37
Inflation pressure, tires 190
Inflation pressure warning FTM, tires 109
Info display, refer to Com‐ puter 91
Initialize, Tire Pressure Moni‐ tor TPM 106
Initializing, Flat Tire Monitor FTM 109
Instrument cluster 80
Instrument cluster, electronic displays 80
Instrument lighting 100
Integrated key 36
Integrated Owner's Manual in the vehicle 29
Intelligent Emergency Re‐ quest 217
Intelligent Safety 110
Intensity, AUTO pro‐ gram 151
Interior equipment 156
Interior lights 100
Interior lights via remote con‐ trol 39
Interior motion sensor 47
Interior rearview mirror, auto‐ matic dimming feature 61
Interior rearview mirror, com‐ pass 158
Interior rearview mirror, man‐ ually dimmable 61
Interval display, service re‐ quirements 88 J
Jacking points for the vehicle jack 214
Joystick, Steptronic transmis‐ sion 76
Jump-starting 218
K
Key/remote control 36
Keyless Go, refer to Comfort Access 43
Key Memory, refer to Per‐ sonal Profile 37
Kickdown, Steptronic trans‐ mission 76
Knee airbag 103
L Lamp replacement 206
Lamp replacement, front 207
Lamp replacement, rear 212
Lane departure warning 119
Lane margin, warning 119
Language on Control Dis‐ play 94
Lashing eyes, securing cargo 176
LATCH child restraint sys‐ tem 64
Launch Control 78
Leather, care 224
LEDs, light-emitting di‐ odes 207
Length, vehicle 230
Letters and numbers, enter‐ ing 25
Light alloy wheels, care 225
Light control 98
Light-emitting diodes, LEDs 207
Lighter 160
Lighting 97 Seite 236ReferenceEverything from A to Z236
Online Edition for Part no. 01 40 2 956 725 - X/14

Opening and closing, withoutremote control 41
Opening and closing, with re‐ mote control 39
Opening the trunk lid with no- touch activation 44
Operating concept, iDrive 18
Optional equipment, standard equipment 6
Outside air, refer to Auto‐ matic recirculated-air con‐
trol 152
Overheating of engine, refer to Coolant temperature 87
P Paint, vehicle 224
Parallel parking assistant 145
Park Distance Control PDC 137
Parked-car ventilation 153
Parked vehicle, condensa‐ tion 174
Parking aid, refer to PDC 137
Parking assistant 145
Parking brake 71
Parking lights 97
Passenger side mirror, tilting downward 60
Pathway lines, rearview cam‐ era 141
PDC Park Distance Con‐ trol 137
Pedestrian warning with city braking function 117
Personal Profile 37
Personal Profile, exporting profiles 38
Personal Profile, importing profiles 38
Pinch protection system, glass sunroof 50
Pinch protection system, win‐ dows 48
Plastic, care 225 Power failure 215
Power sunroof, glass 49
Power windows 48
Pressure, tire air pres‐ sure 190
Pressure warning FTM, tires 109
Profile, refer to Personal Pro‐ file 37
Programmable memory but‐ tons, iDrive 24
Protective function, glass sunroof 50
Protective function, win‐ dows 48
Push-and-turn reel, refer to Controller 18, 19
R Radiator fluid 203
Radio-operated key, refer to Remote control 36
Radio ready state 67
Radio, see user's manual for Navigation, Entertainment
and Communication
Rain sensor 74
Rear lights 214
Rear socket 161
Rear turn signal, bulb replace‐ ment 212
Rearview camera 140
Rearview mirror 59
Rear window defroster 152
Recirculated-air filter 153
Recirculated-air mode 152
Recommended fuel grade 188
Recommended tire brands 195
Refueling 186
Remaining range 88
Remote control/key 36
Remote control, auxiliary air conditioning, key 155 Remote control, malfunc‐
tion 40
Remote control, univer‐ sal 156
Replacement fuse 215
Replacing parts 206
Replacing wheels/tires 195
Reporting safety defects 10
RES button 132
RES button, see Active Cruise Control, ACC 129
RES button, see Cruise con‐ trol 135
Reserve warning, refer to Range 88
Reset, Tire Pressure Monitor TPM 106
Residual cooling 154
Retaining straps, securing cargo 176
Retreaded tires 195
Roadside parking lights 98
Roller sunblinds 49
RON recommended fuel grade 188
Roofliner 17
Roof load lidacity 231
Roof-mounted luggage rack 177
Rope for tow-starting/ towing 220
RSC Run Flat System Com‐ ponent, refer to Run-flat
tires 196
Rubber components, care 225
Run-flat tires 196
S Safe braking 173
Safety 7
Safety belt reminder for driv‐ er's seat and front passen‐
ger seat 56
Safety belts 55 Seite 238ReferenceEverything from A to Z238
Online Edition for Part no. 01 40 2 956 725 - X/14

Safety belts, care 225
Safety of the hybrid sys‐ tem 221
Safety reel, windows 49
Safety systems, airbags 102
Saving fuel 178
Screen, refer to Control Dis‐ play 18
Screwdriver, see Onboard ve‐ hicle tool kit 206
Screw thread, see screw thread for tow fitting, screw
thread for tow fitting 221
Seat and mirror memory 58
Seat belts, refer to Safety belts 55
Seat heating, front 55
Seat heating, rear 55
Seating position for chil‐ dren 62
Seats 52
Selection list in instrument cluster 91
Selector lever, Steptronic transmission 76
Sensors, care 226
Service and warranty 8
Service requirements, Condi‐ tion Based Service
CBS 204
Service requirements, dis‐ play 88
Service, Roadside Assis‐ tance 218
Services, ConnectedDrive
Servotronic 128
SET button, see Active Cruise Control, ACC 129
SET button, see Cruise con‐ trol 135
Settings, locking/unlock‐ ing 45
Settings on Control Dis‐ play 94
Settings, storing for seat, mir‐ ror 58 Shift paddles on steering
wheel 78
Side airbags 102
Side View 142
Signaling, horn 14
Signals when unlocking 45
Silent Start, electric drive readiness 68
Sitting safely 52
Size 230
Slide/tilt glass roof 49
Smallest turning radius 230
Snow chains 196
Socket 160
Socket, OBD Onboard Diag‐ nostics 204
SOS button 217
Spare fuse 215
Specified engine oil types 202
Speed, average 92
Speed limit detection, com‐ puter 92
Speed limiter, display 89
Speed Limit Information 89
Speed warning 93
Split screen 23
SPORT+ - program, Dynamic Driving Control 127
Sport displays, torque dis‐ play, performance dis‐
play 93
SPORT program, Dynamic Driving Control 127
Sport program, transmis‐ sion 77
Sport steering, variable 126
Stability control systems 124
Standing air conditioning, re‐ mote control 46
Start/Stop button 67
Start function during malfunc‐ tion 37
Starting the combustion en‐ gine 68 Status control display,
tires 106
Status information, iDrive 23
Status of Owner's Manual 7
Steering assistance 128
Steering wheel, adjusting 61
Steering wheel heating 61
Steptronic Sport transmis‐ sion 78
Steptronic transmission 76
Storage compartments 164
Storage compartments, loca‐ tions 164
Storage, tires 196
Storing the vehicle 226
Summer tires, tread 194
Sun visor 160
Supplementary text mes‐ sage 86
Surround View 140
Switch for Dynamic Driv‐ ing 126
Switch-on times, parked-car ventilation 154
Switch, refer to Cockpit 14
Symbols 6
Symbols in the status field 23
T Tachometer 87
Tail lights 212
Technical changes, refer to Safety 7
Technical data 230
Telephone, see user's manual for Navigation, Entertain‐
ment and Communication
Temperature, automatic cli‐ mate control 151
Temperature display for ex‐ ternal temperature 87
Temperature, engine oil 87
Tempomat, refer to Active Cruise Control 129
Terminal, starting aid 219 Seite 239Everything from A to ZReference239
Online Edition for Part no. 01 40 2 956 725 - X/14