2014 BMW ACTIVE HYBRID 3 trunk

Coasting to a standstill and braking phases are
used more often to recover energy.
eDRIVE electric driving and the Auto Start
Stop function will also be deactivated.
Fast charging
In exceptional cases it can be charged in place,
such as before extended idle phases in order
to prevent damage to the high-voltage battery.1.Start the engine.2.Engage transmission position P and set
parking brake.3.Press and hold down brake pedal.4.Use the accelerator pedal to maintain an
engine speed of approx. 2,000 rpm.
After a few minutes, the high-voltage battery is
fully charged again.
The battery charge indicator in the instrument
cluster, refer to page 81, is used to check the
status.
General driving notes
Closing the trunk lid Drive with the trunk lid closed
Only drive with the tailgate closed; other‐
wise, in the event of an accident or braking and
evasive maneuvers, passengers and other traf‐
fic may be injured, and the vehicle may be
damaged. In addition, exhaust fumes may en‐
ter the vehicle interior.◀
If driving with the tailgate open cannot be
avoided:
▷Close all windows and the glass sunroof.▷Greatly increase the air flow from the vents.▷Drive moderately.Hot exhaust system
Hot exhaust system
High temperatures are generated in the
exhaust system.
Do not remove the heat shields installed and
never apply undercoating to them. Make sure
that flammable materials, e. g. hay, leaves,
grass, etc. do not come in contact with the hot
exhaust system while driving, while in idle po‐
sition mode, or when parked. Such contact
could lead to a fire, resulting in an increased
risk of serious personal injury as well as prop‐
erty damage.
Do not touch hot exhaust pipes; otherwise,
there is a danger of getting burned.◀
Mobile communication devices in the
vehicle
Mobile communication devices in the ve‐
hicle
It is not recommended to use mobile phones,
such as mobile phones, in the vehicle interior
without a direct connection to an external aer‐
ial. Otherwise, the vehicle's electronics and
mobile communication devices can interfere
with each other. In addition, there is no assur‐
ance that the radiation generated during trans‐
mission will be conducted away from the vehi‐
cle interior.◀
Hydroplaning Hydroplaning
When driving on wet or slushy roads, re‐
duce your speed to prevent hydroplaning.◀
On wet or slushy roads, a wedge of water can
form between the tires and road surface.
This phenomenon is referred to as hydroplan‐
ing. It is characterized by a partial or complete
loss of contact between the tires and the road
surface, ultimately undermining your ability to
steer and brake the vehicle.Seite 172Driving tipsThings to remember when driving172
Online Edition for Part no. 01 40 2 956 725 - X/14

Securing cargo
Stow and secure the cargo as described
above; otherwise it may present a danger to
the occupants, e.g., during braking and evasive
maneuvers.◀
Roof-mounted luggage rack Note
Roof racks are available as special accessories.
Securing
Follow the installation instructions of the roof
rack.
Roof drip rail with flaps
The anchorage points are located in the roof
drip rail above the doors.
Fold the cover outward.
Loading Be sure that adequate clearance is maintained
for tilting and opening the glass sunroof.
Because roof racks raise the vehicle's center
of gravity when loaded, they have a major ef‐
fect on vehicle handling and steering re‐
sponse.
Therefore, note the following when loading
and driving:
▷Do not exceed the approved roof/axle
loads and the approved gross vehicle
weight.▷Distribute the roof load uniformly.▷The roof load should not extend past the
loading area.▷Always place the heaviest pieces on the
bottom.▷Secure the roof luggage firmly, e.g., tie
with ratchet straps.▷Do not let objects project into the opening
path of the trunk lid.▷Drive cautiously and avoid sudden acceler‐
ation and braking maneuvers. Take corners
gently.Seite 177LoadingDriving tips177
Online Edition for Part no. 01 40 2 956 725 - X/14

Tail lights, bulb replacement
At a glance1Turn signal2Reversing lamp3Inside brake lamp4Tail lights5Outside brake lamp
Bulb replacement, exterior tail lights General information
Follow general instructions, refer to page 206.
Turn signal: 21-watt bulb, P21WLL.
Outer brake lamp: 21-watt bulb, H21W.
The tail lights feature LED technology. Contact
your service center in the event of a malfunc‐
tion.
Use caution when replacing the bulb
Use caution and proceed one step at a
time when replacing the bulbs to prevent dam‐
age to the tail lights or the vehicle.◀
Removing the exterior tail lamp1.Open trunk lid.2.Use the screwdriver from the onboard ve‐
hicle tool kit to loosen the screw, arrow 1,
and remove the cover, arrow 2.3.Use the screwdriver handle to loosen the
two nuts, arrows 1 and 2, and remove. The
tail lamp is still attached to a rubber mount
on the outside.4.Grasp the inner edge of the tail lamp and
carefully swing it back and out of the rub‐
ber mount, arrow 1. Use your free hand to
hold it in place in order to prevent the tail
lamp from coming loose suddenly. Make
sure that the foam rubber sealing ring is on
the centering pin, arrow 2.Seite 212MobilityReplacing components212
Online Edition for Part no. 01 40 2 956 725 - X/14

5.Remove the connecting line from the clip
on the bulb holder.6.Press and hold the catch at the top on the
connector of the connecting line and re‐
move the connector from the bulb holder.
Replacing the bulbs
1.Loosen the four fasteners, arrow 1, on the
bulb holder and remove the bulb holder
from the tail lamp, arrow 2.2.Press the defective bulb gently into the
socket, turn counterclockwise and remove.3.Proceed in the reverse order to insert the
new bulb and attach the bulb holder. Make
sure that the bulb holder engages in all fas‐
teners.
Installing the tail lamp
1.Connect the connecting line to the tail
lamp and secure the bulb holder in the clip.2.Make sure that the foam rubber sealing
ring is on the centering pin, arrow 2, and is
not damaged.3.Position and firmly press the outer part of
the tail lamp onto the rubber mount, ar‐
row 1 and the inner part onto the centeringcomponent, arrow 2. Make sure that the
tail lamp engages in the rubber mount.4.Screw the tail lamp on with the two nuts.5.Insert and secure the cover. Make sure that
the tubular seal is not pinched.
Lights in the trunk lid
General information
Follow general instructions, refer to page 206.
Reversing lights: 16-watt bulb, PW16W.
Inner brake lights: 21-watt bulb, H21W
Accessing the lights
1.If needed, remove warning triangle, refer to
page 218, and bracket with the screw‐
driver from the onboard vehicle tool kit, re‐
fer to page 206.2.Use the screwdriver from the onboard ve‐
hicle tool kit to loosen and completely re‐
move the screws on the trim.3.Carefully loosen the trim from the trunk lid,
starting at the edge and working towardSeite 213Replacing componentsMobility213
Online Edition for Part no. 01 40 2 956 725 - X/14

the area around the recessed grips. Make
sure that the trim does not become stuck.4.Carefully swing out the trim.
Replacing the reversing lamp and inner
brake lamp
1.Loosen the two holders, arrow 1 and pull
down on the lamp holder to remove, ar‐
row 2.2.Unscrew the defective bulb of the revers‐
ing or brake lamp from its socket counter‐
clockwise.3.Insert the new bulb.
Installing the bulb holder
1.Slide the bulb holder onto the two guide
pins, arrow 1. Insert the two contacts, ar‐
row 2, into the connections, arrow 3.2.Press on the bulb holder. Make sure that
the two exterior holders latch into place.3.Swing the trim back onto the trunk lid and
secure.Rear lamp, license plate lamp and
central brake lamp
Follow general instructions, refer to page 206.
These lights are made using LED technology.
Contact your service center in the event of a
malfunction.
Changing wheels
Hints When using run-flat tires or sealants, a tire
does not need to be changed immediately in
the event of pressure loss due to a flat tire.
Which is why no spare tire is available.
The tools for changing wheels are available as
accessories from your service center.
Jacking points for the vehicle jack
The jacking points for the vehicle jack are lo‐
cated at the positions shown.
Position the vehicle jack only at the loca‐
tions shown
There are also hybrid components under the
vehicle that are faded by the underbody panel‐
ing.
Make sure not to damage any of the under‐
body paneling parts.
Otherwise, there is the risk of fatal injury from
electrocution due to damaged high-voltage
components.◀
Seite 214MobilityReplacing components214
Online Edition for Part no. 01 40 2 956 725 - X/14

steps to help you under certain circum‐
stances.
For this, data are transmitted to the BMW
Response Center which serve to deter‐
mine the necessary rescue measures. E. g.
the current position of the vehicle, if it can
be established.▷If the LED is flashing green, but the BMW
Response Center can no longer be heard
via the speaker, you can nevertheless still
be heard at the BMW Response Center.
Initiating an Emergency Request
automatically
Under certain conditions, an Emergency Re‐
quest is automatically initiated immediately af‐
ter a severe accident. Automatic Collision Noti‐
fication is not affected by pressing the SOS
button.
Warning triangle
The warning triangle is located on the inside of
the trunk lid.
To remove, loosen the bracket.
First aid kit NoteSome of the articles have a limited service life.
Check the expiration dates of the contents
regularly and replace any expired items
promptly.
Storage
The first aid kit is located in a compartment un‐
der the cargo floor panel.
Roadside Assistance Service availability
Roadside Assistance can be reached around
the clock in many countries. You can obtain as‐
sistance there in the event of a vehicle break‐
down.
Roadside Assistance The Roadside Assistance phone number can
be viewed on the iDrive or a connection to
Roadside Assistance can be established di‐
rectly.
For additional information, see user's manual
for Navigation, Entertainment and Communi‐
cation.
Jump-starting
Hints
If the battery is discharged, an engine can be
started using the battery of another vehicle
and two jumper cables. Only use jumper ca‐
bles with fully insulated clamp handles.
To prevent personal injury or damage to both
vehicles, adhere strictly to the following proce‐
dure.
Seite 218MobilityBreakdown assistance218
Online Edition for Part no. 01 40 2 956 725 - X/14

Emergency unlocking, trunklid 43
Energy recovery, CHARGE 71
Engine, automatic off 69
Engine compartment 198
Engine compartment, work‐ ing in 199
Engine coolant 203
Engine oil 200
Engine oil, adding 201
Engine oil additives 201
Engine oil change 202
Engine oil filler neck 201
Engine oil temperature 87
Engine oil types, alterna‐ tive 202
Engine oil types, ap‐ proved 202
Engine start during malfunc‐ tion 37
Engine start, jump-start‐ ing 218
Engine temperature 87
Entering a car wash 223
Equipment, interior 156
Error displays, see Check Control 83
ESP Electronic Stability Pro‐ gram, refer to DSC 124
Exchanging wheels/tires 195
Exhaust system 172
Exterior mirror, automatic dimming feature 60
Exterior mirrors 59
External start 218
External temperature dis‐ play 87
External temperature warn‐ ing 87
Eyes for securing cargo 176
F
Failure message, see Check Control 83 False alarm, refer to Uninten‐
tional alarm 47
Fan, refer to Air flow 152
Filler neck for engine oil 201
Fine wood, care 225
First aid kit 218
Fitting for towing, see tow fit‐ ting 221
Flat tire, changing wheels 214
Flat Tire Monitor FTM 109
Flat tire, Tire Pressure Moni‐ tor TPM 105
Flat tire, warning lamp 106, 109
Flooding 173
Floor carpet, care 226
Floor mats, care 226
Fold down the rear seat back‐ rest, see Though-loading
system 162
Fold-out position, wiper 75
Foot brake 173
Front airbags 102
Front-end collision warning with braking function 114
Front-end collision warning with City Braking func‐
tion 111
Front fog lights 100
Front fog lights, front, bulb re‐ placement 211
Front lights 207
front-seat passenger airbags, automatic deactivation 104
Front-seat passenger airbags, indicator lamp 104
FTM Flat Tire Monitor 109
Fuel 188
Fuel consumption, refer to Average fuel consump‐
tion 92
Fuel filler flap 186
Fuel gauge 87
Fuel lid 186
Fuel quality 188 Fuel recommendation 188
Fuel, tank capacity 231
Functions, hybrid system 31
Fuse 215
G
Garage door opener, refer to Universal Integrated Remote
Control 156
Gasoline 188
Gear change, Steptronic transmission 76
Gear shift indicator 89
General driving notes 172
Glare shield 160
Glass sunroof, powered 49
Glove compartment 164
Gross vehicle weight, ap‐ proved 231
H
Handbrake, refer to parking brake 71
Hand-held transmitter, alter‐ nating code 157
Hazard warning flashers 217
Head airbags 102
Headlight control, auto‐ matic 98
Headlight courtesy delay fea‐ ture 97
Headlight courtesy delay fea‐ ture, remote control 46
Headlight flasher 73
Headlight glass 207
Headlights 207
Headlights, care 224
Headlight washer system 73
Head restraints 52
Head restraints, front 56
Head restraints, rear 57
Head-up Display 95
Head-up Display, care 226
Heavy cargo, stowing 176 Seite 235Everything from A to ZReference235
Online Edition for Part no. 01 40 2 956 725 - X/14

Height, vehicle 230
High-beam Assistant 99
High beams 73
High beams/low beams, refer to High-beam Assistant 99
High-voltage battery, charge indicator 81
High-voltage battery, dis‐ charge 171
Hills 173
Hill start assistant, refer to Drive-off assistant 128
Hints 6
Holder for beverages 166
Hood 199
Horn 14
Hotel function, trunk lid 42
Hot exhaust system 172
HUD Head-up Display 95
Hybrid system, adapting to the course of the road 83
Hybrid system, at a glance 31
Hybrid system, automatic de‐ activation 222
Hybrid system, contact with water 222
Hybrid system, displays 81
Hybrid system, safety 221
Hydroplaning 172
I Ice warning, see External temperature warning 87
Icy roads, see External tem‐ perature warning 87
Identification marks, tires 192
Identification number, see ve‐ hicle identification num‐
ber 10
iDrive 18
Ignition key, refer to Remote control 36
Ignition off 67
Ignition on 67 Indication of a flat
tire 106 , 109
Indicator and alarm lamps, see Check Control 83
Indicator lamp, see Check Control 83
Individual air distribution 152
Individual settings, refer to Personal Profile 37
Inflation pressure, tires 190
Inflation pressure warning FTM, tires 109
Info display, refer to Com‐ puter 91
Initialize, Tire Pressure Moni‐ tor TPM 106
Initializing, Flat Tire Monitor FTM 109
Instrument cluster 80
Instrument cluster, electronic displays 80
Instrument lighting 100
Integrated key 36
Integrated Owner's Manual in the vehicle 29
Intelligent Emergency Re‐ quest 217
Intelligent Safety 110
Intensity, AUTO pro‐ gram 151
Interior equipment 156
Interior lights 100
Interior lights via remote con‐ trol 39
Interior motion sensor 47
Interior rearview mirror, auto‐ matic dimming feature 61
Interior rearview mirror, com‐ pass 158
Interior rearview mirror, man‐ ually dimmable 61
Interval display, service re‐ quirements 88 J
Jacking points for the vehicle jack 214
Joystick, Steptronic transmis‐ sion 76
Jump-starting 218
K
Key/remote control 36
Keyless Go, refer to Comfort Access 43
Key Memory, refer to Per‐ sonal Profile 37
Kickdown, Steptronic trans‐ mission 76
Knee airbag 103
L Lamp replacement 206
Lamp replacement, front 207
Lamp replacement, rear 212
Lane departure warning 119
Lane margin, warning 119
Language on Control Dis‐ play 94
Lashing eyes, securing cargo 176
LATCH child restraint sys‐ tem 64
Launch Control 78
Leather, care 224
LEDs, light-emitting di‐ odes 207
Length, vehicle 230
Letters and numbers, enter‐ ing 25
Light alloy wheels, care 225
Light control 98
Light-emitting diodes, LEDs 207
Lighter 160
Lighting 97 Seite 236ReferenceEverything from A to Z236
Online Edition for Part no. 01 40 2 956 725 - X/14