2014 BMW 6 SERIES COUPE brake sensor

every time the engine is started using the
Start/Stop button:▷Front-end collision warning, refer to
page 109.▷Pedestrian warning, refer to page 115.
Note
Personal responsibility
The system does not serve as a substi‐
tute for the driver's personal judgment of the
traffic situation.
Be aware of the traffic situation and the vehi‐
cle's surroundings at all times, otherwise acci‐
dents are still possible despite all warnings.◀
At a glance
Button in the vehicle
Intelligent Safety button
Camera
The camera is found near the interior rearview
mirror.
Keep the windshield in the area behind the in‐
terior rearview mirror clean and clear.
Switching on/offThe Intelligent Safety systems are automati‐
cally active after every departure.
Press button: the systems are turned
off. The LED goes out.
Press button: the systems are turned on. The
LED lights up.
Settings can be made on the Control Display.
Front-end collision warning
Depending on the equipment, the collision
warning system consists of one of the two sys‐
tems:▷Front-end collision warning with City Brak‐
ing function, refer to page 112.▷Front-end collision warning with braking
function, refer to page 109.
Front-end collision warning
with braking function
The concept The ystem can help prevent accidents. If an
accident cannot be prevented, the system will help reduce the collision speed.
The system sounds a warning before an immi‐
nent collision and actuates brakes independ‐
ently if needed.
The automatic braking intervention may be
executed with maximum braking force and for
a brief period only as necessary.
If the vehicle is equipped with Active Cruise
Control with Stop & Go, the front-end collision
warning is controlled via the cruise control ra‐
dar sensor in conjunction with a camera.
Seite 109SafetyControls109
Online Edition for Part no. 01 40 2 956 387 - X/14

Above approx. 130 mph/210 km/h the braking
intervention occurs as a brief braking pressure.
No automatic delay occurs.
The braking intervention can be interrupted by
stepping on the accelerator pedal or by ac‐
tively moving the steering wheel.
Object detection can be restricted. Limitations
of the detection range and functional restric‐
tions are to be considered.
Tow-starting and towing
For towing the vehicle turn, switch off the
Intelligent Safety systems; otherwise malfunc‐
tions of the individual braking systems might
lead to accidents.◀
System limits Be alert
Due to system limitations, warnings may
be not issued at all, or may be issued late or
improperly. Therefore, always be alert and
ready to intervene; otherwise, there is the risk
of an accident.◀
Detection range
The system's detection potential is limited.
Thus a warning might not be issued or be is‐
sued late.
E. g. the following situations may not be de‐
tected:▷Slow moving vehicles when you approach
them at high speed.▷Vehicles that suddenly swerve in front of
you, or sharply decelerating vehicles.▷Vehicles with an unusual rear appearance.▷Two-wheeled vehicles ahead of you.
Functional limitations
The system may not be fully functional in the
following situations:
▷In heavy fog, rain, sprayed water or snow‐
fall.▷In tight curves.▷If the driving stability control systems are
limited or deactivated, e.g., DSC OFF.▷If, depending on the vehicle equipment
version, the field of view of the camera in
the mirror or the radar sensor is dirty or ob‐
scured.▷Up to 10 seconds after the start of the en‐
gine, via the Start/Stop knob.▷During calibration of the camera immedi‐
ately after vehicle shipment.▷If there is constant blinding effects be‐
cause of oncoming light, e.g., from the sun
low in the sky.
Warning sensitivity
The more sensitive the warning settings are,
the more warnings are displayed. However,
there may also be an excess of false warnings.
Front-end collision warning
with City Braking function
The concept The ystem can help prevent accidents. If an
accident cannot be prevented, the system will
help reduce the collision speed.
The system sounds a warning before an immi‐
nent collision and actuates brakes independ‐
ently if needed.
The automatic braking intervention is done
with limited force and duration.
A camera in the area of the rearview mirror
controls the system.
The front-end collision warning is available
even if cruise control has been deactivated.
With the vehicle approaching another vehicle
intentionally the collision warning is delayed
avoiding false alarm.
Seite 112ControlsSafety112
Online Edition for Part no. 01 40 2 956 387 - X/14

This is displayed in the speedometer and
briefly in the instrument cluster. Displays in the
instrument cluster, refer to page 139.
When cruise control is maintained or stored,
DSC Dynamic Stability Control will be turned
on if needed.
Changing the speed
Press the rocker reel up or down repeatedly
until the desired speed is set.
If active, the displayed speed is stored and the vehicle reaches the stored speed when the
road is clear.▷Each time the rocker reel is pressed to the
point of resistance, the desired speed in‐
creases or decreases by approx.
1 mph/1 km/h.▷Each time the rocker reel is pressed past
the point of resistance, the desired speed
increases or decreases by a maximum of
5 mph/10 km/h.
Hold the rocker reel in position to repeat the
action.
Distance Select a distance
Adjust the distance according to the traf‐
fic and weather conditions; otherwise, there is
the risk of an accident. Maintain the prescribed
safety distance.◀
Reduce distance Press button repeatedly until the de‐
sired distance is set.
Instrument cluster will display selected dis‐
tance, refer to page 139.
Increase distance Press button repeatedly until the de‐
sired distance is set.
Instrument cluster will display selected dis‐
tance, refer to page 139.
Calling up the desired speed and
distance
While driving Press button with the system
switched on.
In the following cases, the stored speed value
is deleted and cannot be called up again:▷When the system is switched off.▷When the ignition is switched off.
While standing
The system brought the vehicle to a complete
standstill:
▷Green marking in the speedometer:
Your vehicle accelerates automatically as
soon as the vehicle in the range of the ra‐
dar sensor moves off.▷Speedometer markings turn orange: no au‐
tomatic driving off.
To accelerate to the desired speed auto‐
matically, press the accelerator or press
the RES or SET button.
Rolling bars in the distance display indicate
that the the vehicle detected by the radar sen‐
sor has driven off.
Your vehicle was brought down to a halt
through stepping on the brake pedal and it is
standing behind another vehicle:
1. Press button to call up a stored
desired speed.2.Release the brake pedal.3.Step on the accelerator briefly, or press the
RES rocker reel when the vehicle ahead of
you drives away.Seite 138ControlsDriving comfort138
Online Edition for Part no. 01 40 2 956 387 - X/14

▷Maximum distance to row of parked vehi‐
cles: 5 ft/1.5 m.
Suitable parking space
▷Gap between two objects with a minimum
length of approx. 5 ft/1.5 m.▷Min. length of gap between two objects:
your vehicle's length plus approx.
4 ft/1.2 m.▷Minimum depth: approx. 5 ft/1.5 m.
Regarding the parking procedure
▷Doors and trunk lid closed.▷Parking brake released.▷When parking in parking spaces on the
driver's side, the corresponding turn signal
must be set where applicable.
At a glance
Button in the vehicle
Parking assistant
Ultrasound sensors
The ultrasound sensors for measuring parking
spaces are located on the side of the vehicle.
To ensure full functionality:
▷Keep the sensors clean and free of ice.▷When using high-pressure washers, do not
spray the sensors for long periods and
maintain a distance of at least 12 in/30 cm.▷Do not put stickers over sensors.
Switching on/off
Switching on with the button Press button.
The LED lights up.
The current status of the parking space search
is indicated on the Control Display.
Parking assistant is activated automatically.
Switching on with the reverse gear
Shift into reverse.
The current status of the parking space search
is indicated on the Control Display.
To activate:
"Parking Assistant"
Switch off
The system can be deactivated as follows:
▷Press button.▷Switch off the ignition.Seite 153Driving comfortControls153
Online Edition for Part no. 01 40 2 956 387 - X/14

MaintenanceVehicle features and options
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems.
BMW maintenance system
The maintenance system indicates required
maintenance measures, and thereby provides
support in maintaining road safety and the op‐
erational reliability of the vehicle.
Condition Based Service
CBS
Sensors and special algorithms take into ac‐
count the driving conditions of your vehicle.
Based on this, Condition Based Service recog‐
nizes the maintenance requirements.
The system makes it possible to adapt the
amount of maintenance corresponding to your
user profile.
Details on the service requirements, refer to
page 86, can be displayed on the Control Dis‐
play.
Service data in the remote control Information on the required maintenance is
continuously stored in the remote control.
Your service center will read out this data and
suggest the right array of service procedures
for your vehicle.
Therefore, hand your service specialist the re‐
mote control with which the vehicle was driven
most recently.Storage periods
Storage periods during which the vehicle bat‐
tery was disconnected are not taken into ac‐
count.
If this occurs, have a service center update the
time-dependent maintenance procedures,
such as checking brake fluid and, if needed,
changing the engine oil and the microfilter/
activated-charcoal filter.
Service and Warranty
Information Booklet for US
models and Warranty and
Service Guide Booklet for
Canadian models
Please consult your Service and Warranty In‐
formation Booklet for US models and Warranty
and Service Guide Booklet for Canadian mod‐ els for additional information on service re‐
quirements.
Maintenance and repair should be performed
by your service center. Make sure to have reg‐
ular maintenance procedures recorded in the
vehicle's Service and Warranty Information
Booklet for US models, and in the Warranty
and Service Guide Booklet for Canadian mod‐
els. These entries are proof of regular mainte‐
nance.
Socket for OBD Onboard
Diagnosis
Note Socket for Onboard Diagnosis
The socket for onboard diagnostics may
only be used by the service center or a work‐
shop that operates in accordance with the
specifications of the vehicle manufacturer withSeite 209MaintenanceMobility209
Online Edition for Part no. 01 40 2 956 387 - X/14

Onboard vehicle tool kit 211
Opening/closing via door lock 39
Opening and closing 34
Opening and closing, without remote control 39
Opening and closing, with re‐ mote control 37
Operating concept, iDrive 18
Optional equipment, standard equipment 6
Outside air, refer to Auto‐ matic recirculated-air con‐
trol 157
Overheating of engine, refer to Coolant temperature 84
P Paint, vehicle 223
Parallel parking assistant 152
Park Distance Control PDC 144
Parked vehicle, condensa‐ tion 174
Parking aid, refer to PDC 144
Parking assistant 152
Parking brake 65
Parking lights 95
Parking lights and roadside parking lights, refer to Light-
emitting diodes, LEDs 213
Parking with Automatic Hold 66
Passenger side mirror, tilting downward 55
Pathway lines, rearview cam‐ era 147
PDC Park Distance Con‐ trol 144
Pedestrian detection, see Night Vision 117
Pedestrian warning with city braking function 115
Personal Profile 35 Personal Profile, exporting
profiles 36
Pinch protection system, glass sunroof 47
Pinch protection system, win‐ dows 45
Plastic, care 224
Power failure 215
Power sunroof, glass 46
Power windows 44
Pressure, tire air pres‐ sure 190
Pressure warning FTM, tires 107
Profile, refer to Personal Pro‐ file 35
Programmable memory but‐ tons, iDrive 23
Protective function, glass sunroof 47
Protective function, win‐ dows 45
Push-and-turn reel, refer to Controller 18
R Radiator fluid 207
Radio-operated key, refer to Remote control 34
Radio ready state 62
Radio, see user's manual for Navigation, Entertainment
and Communication
Rain sensor 69
Rear axle steering 131
Rear lights 213
Rearview camera 146
Rearview mirror 55
Rear window defroster 158
Recirculated-air mode 157
Recommended fuel grade 188
Recommended tire brands 199
Refueling 186 Remaining range 85
Remote control/key 34
Remote control, malfunc‐ tion 38
Remote control, parked-car heating/ventilation 160
Remote control, univer‐ sal 162
Replacement fuse 215
Replacing bulbs, see Lamp replacement 211
Replacing parts 211
Replacing wheels/tires 198
Reporting safety defects 9
RES button 138
RES button, see Active Cruise Control, ACC 135
RES button, see Cruise con‐ trol 142
Reserve warning, refer to Range 85
Reset, Tire Pressure Monitor TPM 104
Residual heat, automatic cli‐ mate control 158
Retaining straps, securing cargo 176
Retreaded tires 199
Reversing lamp, bulb replace‐ ment 214
Roadside parking lights 96
Roller sunblinds 45
Roll stabilization, refer to Adaptive Drive 130
Roll stabilization, refer to Dy‐ namic Drive 130
RON recommended fuel grade 188
Rope for tow-starting/ towing 220
RSC Run Flat System Com‐ ponent, refer to Run-flat
tires 200
Rubber components, care 224
Run-flat tires 200 Seite 238ReferenceEverything from A to Z238
Online Edition for Part no. 01 40 2 956 387 - X/14

Tail and brake lights 213
Tail lights 213
Tail lights, bulb replace‐ ment 213
Technical changes, refer to Safety 7
Technical data 228
Telephone, see user's manual for Navigation, Entertain‐
ment and Communication
Temperature, automatic cli‐ mate control 156
Temperature display for ex‐ ternal temperature 84
Temperature, engine oil 84
Terminal, starting aid 219
Text message, supplemen‐ tary 83
Theft alarm system, refer to Alarm system 43
Thermal camera, see Night Vision 117
Thigh support 49
Tilt alarm sensor 44
Tilt glass roof 46
Tilt, seats 48
Time of arrival 90
Tire damage 198
Tire identification marks 196
Tire inflation pressure 190
Tire inflation pressure moni‐ tor, refer to FTM 107
Tire Pressure Monitor TPM 103
Tires, changing 198
Tires, everything on wheels and tires 190
Tires, run-flat tires 200
Tire tread 197
Tone, see user's manual for Navigation, Entertainment
and Communication
Tool 211
Top View 150
Total vehicle weight 229
Touchpad 21 Tow fitting 221
Towing 220
Tow lug, see tow fitting 221
Tow-starting 220
TPM Tire Pressure Moni‐ tor 103
Traction control 128
TRACTION, driving dynam‐ ics 128
TRACTION program, Dy‐ namic Driving Control 132
Transmission lock, electronic unlocking 74
Transmission, see Steptronic transmission 71
Transporting children safely 58
Tread, tires 197
Trip computer 90
Triple turn signal activa‐ tion 68
Trip odometer 84
Trunk lid closing 40
Trunk lid, emergency unlock‐ ing 40
Trunk lid, hotel function 40
Trunk lid opening 39
Trunk lid via remote con‐ trol 38
Turning circle 228
Turning circle lines, rearview camera 148
Turn signals, operation 68
Turn signals, rear, bulb re‐ placement 213
U
Unintentional alarm 44
Units of measure 92
Universal remote control 162
Unlock button, Steptronic transmission 72
Unlocking/locking via door lock 39 Unlocking/locking with re‐
mote control 37
Unlocking, settings 42
Updates made after the edito‐ rial deadline 6
Upholstery care 224
USB interface 167
V
Vanity mirror 164
Variable steering, Integral Ac‐ tive Steering 131
Vehicle battery 215
Vehicle battery, replac‐ ing 215
Vehicle, break-in 172
Vehicle care 223
Vehicle features and op‐ tions 6
Vehicle identification num‐ ber 9
Vehicle jack 214
Vehicle paint 223
Vehicle storage 225
Vehicle wash 222
Ventilation 159
Venting, see ventilation 159
Vent, see ventilation 159
VIN, see vehicle identification number 9
Voice activation system 26
W Warning and indicator lamps, see Check Control 80
Warning displays, see Check Control 80
Warning messages, see Check Control 80
Warning triangle 218
Washer fluid 70
Washer fluid reservoir, ca‐ pacity 230 Seite 240ReferenceEverything from A to Z240
Online Edition for Part no. 01 40 2 956 387 - X/14