2014 AUDI S8 key

@ Tips
-In fo rmati on re g arding convenience
opening/closing ¢
page 34.
-The panoramic sunroof wi ll only open at
temperatures above -4 °F (-20 °C).
- To preven t both roof segments from co l­
lid ing with one another, you do not need
to
- tilt the rear roof segme nt if the front
roof segment is a lready open .
- close the front roof segment if the rear roof segment is already ti lted .
Opening/closing the sun shade
App lies to vehicles: with pa noramic sunroof
© Front sun shade
.. To open the sun shade completely, slide the
button
G;J back to just before the second lev­
el ¢
page 44, fig. 35 .
.. To close the sun shade comple tely, slide the
button
G;J forwa rd b riefly to the second lev­
el.
.. To se lect a partially ope n position, slide the
button ~ to the first level until t he des ired
pos ition is reached.
© Rear sun shade
.. To open the s un shade completely, press the
button
G;J in the rear door briefly to the sec­
ond leve l¢
page 44, fig. 36 .
.. To close the sun shade completely, p ull the
button ~ up to the second level¢
A .
.. To select a partially ope n position, press/
pull the button
G;J to the first level unti l the
d esired position is reached . O r
.. To ope rate the s un shade from the cockpit,
press the
I REAR MODE I but ton ¢ page 44 ,
fig . 35 . You can now open/close the rea r sun
shade using the button ~ in the headliner.
A WARNING
-
Be ca reful when closi ng the pa noramic
sunroof -otherwise ser ious injury cou ld re­
sult! For this reason, a lways take the ign i­
tion key with yo u when leav ing the vehicle .
Opening and clo sin g 45
Roof segment/sun shade emergency
closing
App lies to vehicles : wi th pano ra mi c sunroof
If the roof segment or sun shade detects an
ob ject in its path w hen it is closing, it will
open again automatically . In this case, you
can then close it with the power emergency
closing func tion .
.. Withi n five seconds after the roof segment
or sun shade opens a utomatica lly, pull the
sw itch until it closes.

.. Turn the knob to the desired vehicle area
and press the knob . The bar that appears in­
dicates the selected brightness.
.. To increase or reduce the brightness, turn
the knob and press it.
Se lecting a color profile*
.. Se lect in the MMI: !CAR ! function b utton >
Ca r sys tems control button > Vehi cle se t­
tings
> In terior light ing > Colo r profile .
The amb ience lighti ng turns on when the
function is activated in the MMI and when you
turn the headlights on whi le the ignition is
switched on.
Adjusting the b rightness
You can ad just the brightness for the four
zones
F ront top , Fr ont f ootwell , Rear top and
Rear footwell o r for All area s at the same
time.
Selecting a color pr ofile
You ca n select from the Ivory , Polar and Ru ­
b y/ Polar
color profiles .
(I) Tips
The settings are automati cally sto red and
a ssigne d to the remote con tro l key that is
in use.
Instrument illumination
You can adjust the brightness of the instru­
ment and display illumina tion.
F ig. 43 In strument ill um ination
.. Press the knob to release it .
.,. Turn the knob toward"-" or"+" to reduce or
i ncrease the brightness .
Clear vision 51
.. Press the knob again to return it to its origi ­
na l position .
(D Tips
The instrumen t illum ina tion (for d ials an d
needles) lights o n when the ignition is
switched on and the vehicle lights are
turned off. As the daylight fades, the illu­ mination of the dials likewise d ims auto­
matically and wi ll go out completely when
the outs ide light is very low. Th is feature is
meant to rem ind you to sw itch on the
headlights whe n outs ide ligh t conditions
be come poo r.
Vision
Sun visors
E ]
-
F ig . 44 Sun visor
The sun visors fo r the driver and passenger
can be re leased from their brackets and
turned toward the doo rs
c:> fig . 44 @. They
can also be moved back and forth lengthwise
in this position.
The m irror light switches on when the cover
over the vanity mirror @opens .
T he re is a shade be twee n the dr iver's and pas­
senger 's s un v isors that can be used to cover
the gap above the rearview mirro r.

52 Clear vis ion
Sun Shade
F ig. 45 Cockp it: Sun shade switch
Fig. 46 Rear door: S un shade button
Exte ndi ng/retr acting the r ea r window
shade*
~ To extend or retract the sun shade fr om the
cockpit ,
press the r.t.l button in the center
console
c> fig . 45.
~ To extend or ret ract the s un shade from the
r e ar of th e vehicle ,
press the rn button in
the door
c> fig. 46.
Extending the rear door sun shades*
~ Close the window in the rear door.
~ To extend t he sun shade from th e driv er's
s eat ,
pull the left/r ight rear power window
switch~ in the driver's door.
~ To extend the sun shade from the rear of
th e vehi cle,
pull the power window sw itch
11:. in the left/right rear door.
Retracting the rea r door sun shades*
~ To retract the sun shade from th e dri ver's
seat ,
press the left/ right rear power window
swit ch~ in the driver's door.
~ T o retract the sun shade from the rear of the
v ehicle ,
press the power window switch~
i n the left/ right rear door. You can adjust the sett
ings for the rear sun
shade so the shade retracts automatically
when you select the reverse gear . Select:
C AR
funct ion button > Car system s control button
> Vehicle settin gs > Automatic rear blind >
On . The settings are automatically stored and
ass igned to the remote control key. The sun
shade extends aga in as soon as the vehicle be­
gins trave ling fo rward a t a speed greater t han
9 mph (1S km/h), as long a s the ign ition has
not been sw itched off in the meantime .
_&. WARNING ~
When lowering or raising the sunshade,
make sure there is noth ing in its way and
that it has a free path to travel. Th is could
cause personal injury.
(D Tips
-
- Pressing the button~ severa l times
consecutive ly can trigger the overload
protection. The sun shade can only be ex­
tended/retracted again after a brief wait­ ing period.
- The rear window sun shade only func­ tions when the vehicle interio r is warmer
than 14°F (-10°().
· Vanity mirror in the rear
Applies to vehicles: with vanity mirrors in the rear
Fig . 47 Rear headliner: vanity mirror
~ Press the b utton to fold the mirror open .
The mirror lighting turns on automatically.
~ To change the mirror's ang le, move it for­
ward/back w ith your hand.

-To help prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipers by hand .
@ Tips
-Commercial hot waxes applied by auto ­
matic car washes affect the cleanability
of the windshield.
- You can also use the service position, for
example, if you want to protect the
windshield from icing by using a cover.
- You cannot activate the service pos ition
when the hood is open.
Mirrors
Adjusting the exterior mirrors
Fig. SO Fo rwar d section of driver's armrest: power mir­
ro r contro ls
Turn the knob to the desired position :
Q/P -In this position, you can adjust the
driver's and front passenger's exter ior mirrors
by turn ing the knob in the desired direction.
@ -The mirrors are heated depending on the
outside temperature .
8 -The exterior mirrors fo ld in. In the MMI,
you can select if the mirrors fold in automati­
cally when you lock the vehicle
c:> page 34.
Tilt function for the passenger's mirror
To help you see the curb when backing into a
parking space, the surface of the mirror tilts
slightly. The knob must be in the P position
for this to happen .
You can adjust the tilted mirror surface by
turning the knob in the desired direction.
When you move out of reverse and into anoth- Clear vi
sion 55
er gear, the new m irror position is stored and
assigned to the key you are using .
T he m irror goes back into its orig inal position
once you drive forward faster than 9 mph (15
km/h) o r switch the ignition off .
A WARNING
-
-Curved (i.e . convex) m irror surfaces in­
crease your field of view. Remember that
veh icles or other objects will appear
smaller and fart her away than when seen
in a flat mirror. If you use th is mirror to
estimate distances of following veh icles
when changing lanes, you could estimate
incor re ctl y and cause an accident.
(D Note
-If the mirror housing is moved uninten­
tionally (for examp le, while pa rking your
vehicle), then you must first fold the m ir­
ror elect rically. Do not readj ust the mir­
ror housing man ually. You could damage
the motor which controls the mirror .
-If you wash the vehicle in an automatic
car wash, you must fold the ex ter ior mir­
rors in to reduce the risk of damage to
the mirrors . Never fold power fo lding ex­
terior mirrors by hand . On ly fold them in
and out using the power controls.
(D Tips
- Th e exterior mirror settings are stored
w ith the memory function*
c::> page 66.
- If there is a malfunction in the electrical
system, you can still adjust the exterior
mirrors by pressing the edge of the m ir­
ror.

66 Seats and storage
Seat memory
Description
Applies to vehicles: wit h memory fu nctio n
The memory function allows you to quickly
and eas ily store and recall personal seating
p rofiles for the dr iver, front passenger and
outer rear seats*. The memory function is op­
erated through the master key and the memo­ ry buttons in the driver's/front passenger's
doors and the rear doors*.
The driver's seating profi le is stored and as ­
signed to the master key each time the vehicle
is locked . The seating profile is recalled auto­
matically when the vehicle is unlocked. If two
Remote control
master key
Driver
Seat X
Head restraint X
Steering wheel* X
Safety belt* X
Both exterior rear-X
view mirrors*
There are two additional buttons in the rea r
doors* that can be used to recall two stored
seating profiles
r:=;,page 67.
Remote control key
Appl ies to vehicles: with memory function
To assign the driver's seat settings to the re­
mote contro l key when locking the vehicle, the
function must be switched on .
.. Se lect :
I CAR I function button > Car systems
control button > Vehicle settings > Seats >
Driver seat > Remote control key> On.
@ Tips
If you do not want another driver's set­
tings to be assigned to the remote control
key, switch off the memory function using
the MMI or the
! OF F! button r:=;, page 67. people
use one vehicle, it is recommended
that each person always uses "their own"
master key.
Two seating profiles can be stored in each of
the driver's/front passenger's doors and one
seat ing profile in each of the rear doors*.
Once stored, these seat ing profiles can be re­
ca lled at any time.
T he following sett ings are stored:
Memory button
Driver Front passenger Outer rear seats*
X
X X
X X
X
X
X
X

68 Seats and storage
Full-length center
console
Overview
Appl ies to vehicles: with full-len gth ce nter console
Fig. 65 Rear: full -length center console
@ · 115 volt socket ¢ page 68
@ · cupholder <=> page 75
© · 12 volt socket c:> page 7 4
@ · Folding table ¢ page 69
® ·center armrest and storage com part ·
ments: to open the deep compartment, press
the r ight button and fo ld the center armrest
upward. To open the compartment fo r the
massage func tion remote con trol*
c:> page 64
and fo r the telephone* , press the left button
and fo ld the center armrest upward.
115-volt socket
App lies to vehicles: with 115 -vo lt socket
The 115-vo lt socket can only be used when
the engine is running¢
A. When you push
the connector all the way into the socket, the
child safety mechan ism releases and current
flows through the socket .
Equipm ent that can be conn ected
Electrical devices can be connected to the 115
volt socket in the veh icle. Power consumption
at the 115-volt socket must not exceed 150
watts (300 watts peak) . Check the power con·
sumpt ion of the equipment on the model
p late .
LED on th e socket
- The socket is ready for use when the L ED is
green.
- If the LED blin ks red, there is a ma lf u nction.
The socket wi ll swi tch off automa tica lly due
to overcu rrent or overheating. The socke t
will switch on again automatica lly after a
coo l-down period. Any devices that are con­
nected and switched on will activate again
automatically
c:> A .
A WARNING
-
- The sockets and the electr ical accessories
connec ted to them operate only when
the ignition is switched on. Incorrect us­
age can lead to ser ious injuries or burns.
To reduce the risk of injuries, neve r leave
chi ldren unattended in the veh icle with
the vehicle key .
- H eavy equipment or plugs with in tegrat­
ed power s upply units can damage the
socket and lead to injur ies .
- Sto re a ll connected e quipment securely
while the veh icle is moving so that they
cannot be thrown through the veh icle in
the event of a braking maneuver or an
accident.
- Never sp ill any liquids on the socket . If
any mo isture gets into the socket, make
certain that all the moisture has dried up before using the socket again.
- Equipment that is connected to the vehi·
cle socket can heat up more than it does
when connected to the public gr id .
- When us ing adapters and extens ion
cords, the child safety for the 115-volt
socket is d isabled and the socket is live.
- Never insert anything other than the
p lug of an appropriate e lectr ical accesso·
ry in to the socket, especially th ings that
conduct e lectr icity, e.g . meta l pens, kn it­
ting needles, etc. in to the cont acts of the
1 15-volt so cket.
- Turn the electrical equ ipment off if the
socket has switc hed off because of over·
heat ing.

7 4 Seats and storage
- Never exceed the maximum perm issible
load carrying capacity of the roof o f your
vehicle, the permissible axle weights and
the permissible total weight of your veh i­
cle
c::, page 289, Weights .
@ For the sake of the environment
As a result of the increased wind resist­
ance created by a roof rack, your vehicle is
using fuel unnecessarily. So remove the
roof rack after using it.
12-volt sockets
Applies to vehicles: 12-volt soc kets
Electrical accessories can be connected to ev­
ery 12-volt socket.
Fig. 75 Sect io n of the trim panel o f th e luggage com­
part ment : 12 -vol t socket
Fig. 76 Rear center conso le: 12-vo lt socket
... Open the socket cover c::, fig . 75 or c::, fig . 76 .
... Inse rt the p lug of the e lectrical device into
the socket.
There is an additional 12 vo lt socket in the
fro nt center console
c::> page 75, fig. 77.
The 12 volt sockets can be used for electr ica l
accessories . Th e power input must not exceed
120 watts . Before you purchase any accessories
, always
read and follow the information in
c::, page 294, Additional accessories and parts
replacemen t.
A WARNING
The sockets and the electrical accessories
connected to them operate only when the
i gnition is switched on . Incorrect usage
ca n lead to ser ious injuries or burns. To re­
duce the risk of inj uries, never leave ch il­
dren unattended in t he vehicle with the ve­
hicle key .
(D Note
To avoid damaging the socket, only use
plugs that fit p roperly.
- Never connect equ ipment that generates
elect rical current, such as a solar panel
or battery charger, to the 12 vol t socket .
T his could damage the vehicle 's elect ri­
cal sys tem .
- The 12 volt socket shou ld only be used
for a short per iod of t i me as a power
so urce for electrical equ ipment . Please
use the electrical sockets in the vehicle
when connecting equipment for longer periods.
@ Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat­
tery can still be drained.

Storage
(upholder
Fig. 77 Center console: front cupho lder
Fig. 78 Section of the rear bench seat: rear cupholder
Front cupholder
.,. To open the cupholder, tap the cover
Q fig . 77, Q &,.
Rear cupholder
.,. To open the cupholder, tap the front strip
Q fig. 18, QA .
In vehicles with a full-length center console in
the rear, the cupholder is located at @
Qpage 68, fig. 65.
A WARNING
Spilled hot liquid can cause an accident
and personal injury .
- Never carry any beverage containers with
hot liquids, such as hot coffee or hot tea,
in the vehicle while it is moving. In case
of an accident, sudden braking or other
vehicle movement, hot liquid could spill, causing scalding burns. Spilled hot liquid
can also cause an accident and personal
injury.
Seats and storage 75
-Use on ly soft cups in the cupholder. Hard
cups and glasses can cause injury in an
accident.
(D Note
Only drink containers with lids should be
carried in the cupholder. Liquid could spill
out and damage your vehicle's electronic
equipment or stain the upholstery, etc.
Cooled glove compartment
The cooled glove compartment only functions
when the AIC system is switched on.
Fig. 79 Glove compar tment: switching cooling mode
on/off
.,. Turn the knob@ counterclockwise to switch
cooling on. The symbols on the knob indi­
cate the correct position
~ fig. 79 .
.,. Turn the knob @ clockwise to switch cooling
off .
The glove compartment cooling mode only
functions when the vehicle A/C system is
switc hed on. If the heating is switched on,
switching the glove compartment cooling mode off is recommended .
A WARNING
Always leave the lid on the glove compart­
ment cover closed while dr iving to reduce
the risk of injury.
a) Tips
The glove compartment can be locked us­
i ng the mechanical key
Q page 32.