2014 AUDI S8 spare wheel

272 What do I do now ?
Spare wheel
App lies to vehicles: with spare wheel
The spare wheel is stored in the wheel well
underneath the floor panel in the luggage
compartment.
Fig. 220 L uggage compartment: spare wheel
Taking out the spare wheel
.,. Lift the cargo floor by the plastic handle
¢fig. 220.
.. Hook the hand le into the luggage compart­
ment weather strip .
.. Turn the large screw¢
fig. 220 counter­
clockwise.
.. Take out the spare tire.
.. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment ¢
page 141.
.,. Unhook the cargo floor before closing the
rear lid.
&_ WARNING
-
Loose items in the passenger compart ­
ment can cause serious personal injury
during hard braking or in an accident.
- Never store the spare wheel or jack and
tools in the passenger compartment.
(D Tips
Check the inflat ion pressure of the spare
tire periodically to keep the tire ready for
use.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel.
.. After you experience a tire failure, pull the
car well away from moving traffic and try to
reach
level ground before you stop ¢ .&_ .
.. All passengers should leave the car and
move to a safe location (for instance, behind
the guardra il)¢ .&_ .
.. Engage the
parking brake to prevent your
vehicle from rolling unintentionally¢ .&_.
.. Move
selector lever to position P ¢ A .
.. If you are towing a trailer, unhitch the trailer
from your vehicle .
.,. Take the
jack and the spare tire out of the
luggage compartment¢
page 270,
¢page 271.
&_ WARNING
You or you r passengers could be injured
while changing a wheel if you do not fol­
l ow these safety precautions:
-If you have a flat tire, move a safe dis­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists .
- Make sure that passengers wait in a safe
p lace away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possib ly slipping off the
jack, always fully set the parking brake
and block the wheel d iagonally opposite
the wheel be ing changed. When one
front wheel is lifted off the ground, plac­ ing the Automatic Transmission in "P"
(Par k) will
not prevent the vehicle from
mov ing.
- Before you change a wheel, be sure the
g rou nd is level and firm. If necessary,
use a sturdy board under the jack.
-

-Always store the vehicle tool ki t, the jack
and t he replaced t ire in the luggage com­
partment ¢
page 141 .
@ Tips
Before chang ing the wheel, you must acti­
vate the jacking mode, so that the auto­
mat ic controls for the Adaptive Air Sus­
pens ion do not make it more difficu lt to
lift the vehicle with the jack¢
page 2 75.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode
c:;.page275.
2. Remove the decorative whe el co ver* . For
mo re deta ils see also
c:;, page 2 73, Deco­
rative wheel covers
or c:;, page 2 7 4,
Wheels with wheel bolt caps.
3 . Loosen the wheel bo lts c:;, page 2 7 4.
4. Locate the proper mo unt ing po int for the
jack and align the jack below that point
c:;, page 2 75.
5 . Rai se the car w ith the jack c:;, page 275.
6. Remove the wheel with the flat tire and
then install
the spare c:;, page 2 76 .
7. Tighten all wheel bo lts light ly .
8 .
Lower the ve hicle w it h the jack.
9 . Use t he wheel bolt wre nch and
firmly
tighte n all whee l bolts c:;. page 274.
10. Rep lace the de corative wheel cover* .
11. D eactivate the vehicle jack mode in t he
MMI:
! CARI fu nction button > Car system s
control button > Servicing & che cks > Air
susp.: jack mode > Off .
The vehicle jack mode sw itches off automati ­
cally at speeds above 10 km/h.
A WARNING
Always read and follow all WARNINGS and
information
c:;, .&. in Raising the vehicle on
page 275
and c:;, page 277.
What do I d o now ? 273
After changing a wheel
A wheel change is not complete without the
doing the following.
.,. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment
c:;, page 141 .
.,. Check the tire pressure on the spare whee l
immed iate ly afte r mounting i t.
.,. As soon as poss ib le, have the
tight ening
torque s
on all wheel bolts checked w ith a
torque wrenc h. The co rrec t tighten ing tor­
que is 90 ft lb (120 Nm).
.,. Have the flat tire
replaced as soon as possi­
ble .
@ Tips
-If you notice that the wheel bo lts a re
corroded and difficult to turn while
chang ing a tire, they should be replaced
before you c heck the tightening torque.
- Drive at reduced speed until you have the tightening torques checked .
- After changing a whee l, the ti re press ure
in all four tires must be checked/correct­
ed and the tire press ure monitoring ind i­
cator must be sto red in the M MI
c:;. page268 .
Decorative wheel covers
Applies to veh icles: w ith decorative w hee l cove rs
The decorative wheel covers mus t be removed
first to access the wheel bolts.
Fi g. 22 1 Chang ing a whee l: Re moving th e w hee l cover
Removing
.,. Insert the hook (provided with the vehicle
t oo l kit) in the ho le in the whee l hub cover .
i,,.

276 What do I do n ow ?
(D Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
{l) Tips
The vehicle jack mode switches off auto ­
mat ica lly at speeds above 10 km/h .
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fi g. 2 26 Cha ngin g a w hee l: u sing t he sc rewdrive r ha n·
dl e (w it h th e blade r emov ed) t o tu rn th e bolt s
F ig. 22 7 Chang ing a w hee l: a lig nm en t pi n inside t he
t op hole
After you have loosened a ll wheel bolts and
ra ised the ve hicle off the ground,
remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwdri v­
er handle
to comp letely remove the top·
most wheel bo lt and set it as ide on a
clean
surface ¢fig . 226 .
.. Sc rew the th readed end of the alignment
pin
from t he tool kit hand-tight into t he
empty bolt hole¢
fig. 22 7 .
.. Then remove the other whee l bolts as de­
scribed above.
.. Take off the whee l leaving the a lignment pin
in the bo lt hole
c::> (D .
Putting on the spare wheel
.. Lift the spare whee l and carefu lly s lide it
over the alignment p in to g uide it in place
¢ (D .
.. Use the hexagonal socket i n the screwdriver
ha ndle to screw in and tighten a ll whee l
bolts
slightly .
.. Remove the alignment pin and inse rt and
tighten the rem aining wheel bol t slightly
like the res t .
.. Turn the jack hand le co unter-cloc kwise to
lower the vehicle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
c;, page 2 74 . Tighten
them
crosswise, from one bolt to the (ap ­
proximately) opposite one, to keep the
wheel ce nte red.
(D Note
When remov ing or installing th e whe el,
th e rim cou ld hit the b rake ro to r and dam­
age the ro tor. W ork caref ully and have a
s eco nd pers on h elp yo u.
{i) Tips
N eve r use the he xagona l socket in the han­
d le of t he s crewdr iver to lo ose n or t igh ten
t he wheel bo lts .
- P ull the revers ible blade from the screw­
dr iver be fore y ou use the hexagon al
s o ck et in t he han dle to tur n t he w heel
bolts.
- W he n m oun tin g ti res w ith
unidirectional
tread design
make sure t he tre ad pat­
t er n is poin ted t he righ t way
c;, page277.
- Th e wheel bolts shou ld be clean and easy
to t urn. Check for dirt an d corrosion on
the mating surfaces of both the w heel

and the hub. R emove a ll dirt from these
su rfaces before remo unt ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread de sign must be
mounted with their tread pattern pointed in
the right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spa re tire w ith a tread patte rn
intended for use in a specific direction, please
note t he following:
- T he direction o f rotation is marked by an a r­
r ow on the side of the tire.
- If the sp are tire has to be install ed in the in­
correct di rection, use the spare tire only
temporar ily since the t ire wi ll not be a ble to
ac hieve its optimum performance character­
ist ics with regard to aquaplaning, noise and
wear.
- We recommend that you pay particular at­
tent ion to this fact during wet weat her and
t h at you adjust your speed to matc h road
condit ions .
- Replace the flat tire w ith a new one and
have it installed on your ve hicle as soon as
poss ib le to restore the hand ling advantages
of a uni direct io na l ti re.
Notes on wheel changing
Please read the information ¢ page 259, New
t ires and repl acing tires and wheels
if you are
goi ng to use a s pare t ire which is differen t
from the tires on your ve hicle.
Afte r you change a tire:
- Check the tire pressure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified s ervice station .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm). What do I do now? 277
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire , they should be replaced before you
check the t ightening torque.
- Replace the flat ti re with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then , drive with extra care and at re­
duced speeds.
A WARNING
- I f you are g oing to eq uip your vehicle
wit h tires o r rims which differ from those
which were factory installed, then be sure to read the information ¢
pag e 259,
N ew tires and replacing tir es and
w heels.
- Always ma ke sure t he damag ed wheel o r
even a fla t tire an d the jack a nd tool ki t
a re prope rly se cu red in t he luggage co m­
p art me nt and a re not loose in the p as­
senger compartment .
- I n an a ccide nt or sudde n maneuver they
could fly forward, injuring anyone in the
veh icle.
- Always s tore da mage d wheel, j ack and
t oo ls se curely in the lugg age comp art­
men t. Othe rwise, in an accident o r su d ­
den maneuver they co uld f ly forwa rd,
causing inju ry to passengers in the veh i­
cle. •
•

Technical Data
Vehicle identification
F ig. 2 42 Veh ide Identificat ion Numbe r (VlN) plate: lo ·
c ation on dri ver 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -IIOO -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JDZ 1LB lA S 18A
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1S A 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 243
T h e vehicle identification label - inside the
luggage co mpartment
Veh icle Id entifica tion Numb er (VlN )
The Veh icle Iden tifica tion Number is located
in different p laces :
- under the w indshield on the driver's side
~fig. 242.
- in the MMI: Select: Function button ICAR ! >
Car syste m s> VIN numb er.
- on the vehicle identification label.
V ehicle ident ific ation lab el
The vehicle identification label is located in
the luggage compartment in the spare wheel
well.
Te chni cal Data 289
The label ~ fig. 243 shows the fo llowing vehi ­
cle data :
(D Vehicle Ident ifi cat ion Number (V IN)
@ Vehicle type, engine output, transmission
@ Engine and transm ission code
@ Paint number and interior
® Optional equipment numbers
The information of the vehicle identification
label can also be found in your Warranty
&
Maintenance booklet.
Saf ety compliance sticker
T he safety compliance sticker is your assur ­
ance that your new veh icle complies with all
applicable Federa l Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured. You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and the vehicle ident ificat ion number of your
vehicle (perforat ion) as well as the Gross Veh i­
cle Weight Rating (GVWR) and the Gross Ax le
Weight Rating (GAWR) .
High volt age warning lab el
The high voltage warning label is located in
the engine compartment next to the engine
hood re lease. The spark ign ition system com­
plies with the Canadian standard IC ES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
doo r jamb on the driver's s ide.
The Gross Vehicle Weight Rat ing includes the
weight of the bas ic vehicle plus fu ll fuel tank,
o il and coo lant, plus maximum load , which in­
cludes passe nger we igh t (1 50 lbs/68 kg pe r
designated sea ting position) and luggage
weight ~.& -
II>

Spare tire
refer to Compact spare tire
271
Spare wheel ....................... 272
Speedometer ....................... 27
Speed rating letter code .. ... .. .. .. .. . 260
Speed warn ing system ...... .. .. .. .. .. 91
Sport different ia l . ...... ... .. .. .. .. . 1 10
Indicator light . . . . . . . . . . . . . . . . . . . . . 23
S tart -Stop-System . . . . . . . . . . . . . . . . . . . 88
E ng ine does not switched off ... .. .. .. 89
Engine starts automatically . ... .. .. .. 89
Indicator lights . . . . . . . . . . . . . . . . . . . . 89
Messages ................... ...... 91
Starting/stopping the engine ......... 89
switch ing off/on .......... .. .. .. .. .. 90
S TART ENGINE STOP b utton ... .. .. .... 84
Start ing from rest . . . . . . . . . . . . . . . . . . . . 87
Starting off with a trailer .............. 88
S tarting the eng ine ..... ... .. .. .. .. .. 84
Steer ing whee l
Ad justing steering column ..... ...... 83
E asy en try featu re .................. 83
I ndicator ligh t . . . . . . . . . . . . . . . . . 17, 2 2
Shift paddles ... ...... ... .. .. .. .. . 119
Steering whee l heating . ... .. .. .. .. .. 82
Steps fo r determining co rrect load lim it . 257
Stopping the engine . . . . . . . . . . . . . . . . . . 84
S to rage ............................ 75
Sunroof ..... .. .. ........... .. .. .... 43
Sun shades Emergency closing (roof) ............. 45
Panoramic sunroof .................. 45
Reardoo~ ........................ 52
Rear window . . . . . . . . . . . . . . . . . . . . . . . 52
Sun visors ... .. ... ..... ... .. .. .. .... 51
Symbo ls
refer to W arning/Indica to r li gh ts ...... 11
T
Tachometer . . . . . . . . . . . . . . . . . . . . . 11, 24
Ta il lights
C leaning ......................... 217
TD I clean diese l
refer to Ad Blue .... .... ... .. .. .. ... 227
Techn ica l data ...................... 289
Technica l mod ifications .............. 295
Index 307
Temperat ure display . .. .. ..... ... .. .. . 24
T e ther anchors .. ................... 194
Tether strap . . . . . . . . . . . . . . . . . . . . . . . 194
T extiles
Cleaning . ... .. .. .. . ... ...... ... .. 219
The first 1,000 miles (1,500 km) and after-
wards ........ .. .... ............... 207
Tie-downs . . . . . . . . . . . . . . . . . . . . . 70, 142
T ips for the environmen t
Saving f uel .. .. .. .. . ... ...... ... .. . 73
tiptron ic (automatic t ransm ission) ..... 116
Tire pressure ....................... 254
T ire pressu re mon itor ing system ....... 266
L oss of air p ress ure .. .. ..... ... .. .. 267
Malfunction ....... . .. .. ..... ... .. 267
Resetting tire pressures . ..... ... .. .. 268
T ires .............................. 248
Serv ice life ....................... 258
speed ra ting lette r code ..... ... .. . .
Tire manu fact uring date ..... ... .. . .
Tire specifications . .. ... .... ... .. . .
Tread depth ..................... .
Uniform tire quality grading ........ .
W' t t' in er
ires ..................... . 2
60
260
260
258
262 263
T ires and vehicle load limi ts .... ... .. .. 256
Tires and wheels Check ing tire p ress ure .............. 254
Co ld tire infla tion pres sure .......... 252
D imens ions ....................... 259
General notes ...... . .. .. ..... ... .. 248
G lossary of tire and loading terminolo-
gy .............................. 249
Low aspect ratio tires ............... 265
New tires and wheels ............... 259
Rep laci ng ... .. ... ................ 260
S now cha ins ... ... ................ 264
Tires and veh icle load lim its ....... .. 256
Whee l bolts ...................... 265
Win ter tires ...................... 263
Tire service life .. .. .. . .. ....... ... .. 258
Too ls . ... .. .. .... .. . .. .. ..... ... .. 270
T o rn o r frayed safety belts ............ 148
Towing Tow truck procedures ............... 285
TPMS Tire pressure mo nitoring system ... .. 267
•
•