2014 AUDI A7 spare wheel

266 What do I do now?
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang ­
ing a wheel .
... After you experience a tire failure, pull the
car well away from moving traffic and try to
reach
level ground before you stop o ,&.
... All passengers should leave the car and
move to a safe location (for instance, behind
the guardrail)
o A-
.. Engage the parking brake to prevent your
vehicle from rolling unintentionally
o ,&.
... Move selector lever to position Po ,& .
• If you are towing a trailer, unhitch the trailer
from your vehicle .
... Take the
jack and the spare tire out of the
luggage compartment
o page 264,
o page265.
A WARNING
You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
- If you have a flat tire,
move a safe dis­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
sudden ly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed . When one
front wheel is lifted off the ground, plac­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm.
If necessary,
use a sturdy board under the jack.
-
-Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
opage 136.
@ Tips
Before changing the whee l, you must acti­
vate the jacking mode, so that the auto­
matic controls for the Adaptive Air Sus­
pension* do not make it more difficult to
lift the vehicle with the jack
o page 268 .
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order.
l. Activate the vehicle jack mode*
opage 268 .
2. Remove the decorative wheel cover* . For
more details see also
o page 267, Deco­
rative wheel covers
or o page 267,
Wheels with wheel bolt caps.
3. Loosen the wheel bolts o page 268.
4. Locate the proper mounting point for the
jack and align the jack below that point
opage 268.
5. Raise the car with the jack o page 268.
6. Remove the wheel with the flat tire and
then install
the spare opage 270.
7. Tighten all wheel bolts lightly .
8.
Lower the vehicle with the jack .
9 . Use the wheel bolt w rench and
firmly
tighten all wheel bolts o page 268.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode * in the
MMI:
I CARI function button > (Ca r)* sys­
tems
control button > Servicing & checks
> Air susp.: jack mode > Off.
The vehicle jack mode* switches off automati­
ca lly at speeds above 6 mph (10 km/h) .
A WARNING ,-
Always read and follow all WARNINGS and
in format ion
o .&. in Raising the vehicle on
page 269
and opage 271.

After changing a wheel
A wheel change is not complete without the doing the following .
• Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment
Q page 136.
• Check the tire pressure on the spare wheel
immediately after mou nting it.
• As soon as possible, have the
tightening
torques
on al l wheel bolts checked with a
torque wrench. The correct tightening tor­
que is 90 ft lb (120 Nm).
• Have the flat tire
replaced as soon as possi­
ble.
(D Tips
- If you notice that the wheel bolts are
corroded and difficult to turn wh ile
changing a tire, they should be replaced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n all four tires must be checked/correct­
ed and the tire pressure mon itor ing indi­
cator must be stored in the MMI
Qpage263 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 210 Ch ang ing a whee l: Removing the wheel cove r
Removing
.. Insert the hook (provided with the veh icle
tool kit) in the hole in the wheel hub cover.
What do I do now? 267
• Pull off th e decorative wheel cover
Qfig. 210.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fig. 211 C hanging a whee l: removing the wheel bolt
caps
Removing
• Push the plastic clip (provided with the vehi­
cle too l kit) over the wheel bo lt cap until the
inner retainers on the clip align w ith the
edge of the cover.
.. Remove the cap with the
plastic clip (veh icle
tool kit)
Qfig . 211 .
Refitting
• Place the caps over the whee l bolts and
push them back on.
The caps are to protect and keep the wheel
bo lts clean .

2 70 What do I do now ?
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 216 Changing a whee l: u sing the screwdriver han­
dle (w ith th e blade removed} to turn the bolts
Fig. 2 17 Changing a w hee l: a lignm en t pi n ins ide t he
top hole
Afte r you have loosened a ll wheel bolts and
r a ised the veh icle off the ground, remove a nd
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal soc ket in th e screwdriv­
er handl e
to complete ly remove the top­
most wheel bo lt and set it as ide on a
clean
s ur face qfig. 216 .
.. Screw the threaded end o f the alignment
pin
from the tool k it hand -tight into the
empty bolt hole
q fig. 217.
.. Then remove the other wheel bo lts as de­
scribed above .
.. Take off the wheel leav ing the alignment pin
in the bolt hole
c:> (D .
Putting on the spare whe el
.. Lift the spare wheel and ca refully slide it
over the a lignment pin to guide it in place
c:> Q).
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all whee l
bolts
slightly.
.. Remove the a lignment pi n and insert and
tighten the remaining wheel bolt slightly
like the rest .
.. Tu rn the jack hand le counter-clockwise to
lower the veh icle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts f irm ly
q page 268 . Tighten
them
crosswise, from one bolt to the (ap ­
proximately) opposite one, to keep the
wheel centered.
(D Note
When remov ing or installing the whee l,
the rim cou ld hit the b rake roto r and dam­
age the roto r. Work carefu lly and have a
second person help you .
(D Tips
Never use the hexagonal socket in the han­
d le of the screwdriver to loosen or tighten
the wheel bolts.
- Pull the reversible blade from the screw ­
dr iver before you use the hexagonal
socket in the hand le to turn the w heel
bolts .
- When mount ing tires w ith
unidirectional
tread design
make sure the tread pat­
t er n is po inted t he righ t way
~page 271.
-The wheel bolts shou ld be clean and easy
t o t urn . Check for dirt an d co rrosion on
the mat ing surfaces of both the w heel
an d t he hub . Remove all d irt from these
s urfa ce s be for e remou nting the whee l.

Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in
the right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire w ith a tread pattern
in tended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the tire will not be able to
achieve its optimum performance character­
istic s with rega rd to aquaplaning, noise and
wear.
- We recommend that you pay particular at­
tention to this fact during wet weather and
that you adjust your speed to match road
conditions.
- Replace the flat tire with a new one and
have it installed on your veh icle as soon as
possib le to restore the handling advantages
of a unid irectiona l tire .
Notes on wheel changing
Please read the information c:> page 254, New
tires and replacing tires and wheels
if you are
going to use a spare t ire which is different
from the tires on your veh icle.
After you change a tire :
-Check the tire pressure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm).
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque. What do I do now? 271
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then , drive with extra care and at re­
duced speeds.
A WARNING
-
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were factory installed, then be
sure to read the information<=>
page 254,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment .
- In an accident or sudden maneuver they
could fly forward, in juring anyone in the
veh icle.
- Always store damaged wheel, jack and
too ls securely in the luggage compa rt­
ment. Otherwise , in an accident or su d­
den maneuver they could fly forward,
causing injury to passengers in the vehi­
cle.
•
•

282 Technical data
Technical data
Vehicle identification
F ig. 23 1 Vehicle I dent ifica tion Num ber (VlN) pla te: lo·
cat ion on driver 's side dash pane l
XXXXX XX · X -XXXX XXX xx
r,"\__l f~ -11!111 · NII. ~ V!Hlll -llllll . NO.
IYP IT'fl'E
XXXXXXXX XX X XXXXXXXX
XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
®i ~~:f :l~~ XXXX XXX XXX
@+ ~~r= XXXX I XXXX XXX I XX M ,. AIIISl./ lflllllS
EOA 7D5 4 UB 6XM SSG 5RW
2E H JDZ llB l AS lBA
3FC 5MU 7Xl
FO A
9G3 OG7 O
YH OJF
TL6 3
KA BEH
UlA X9B QZ 7
l XW
8Q3 9Q8 82 4 020
7T6 CV 7 7KO 4X3 2K2
3L4 4 KC 3YO 4I3 502
lS A 7GB Q1A 4GQ
XX X
XX X XX X XXXX
Fig. 23 2 The ve hicle identi ficat ion label -inside the
luggage co mpa rtmen t
Vehicle Identification Number (VlN )
The Ve hicle Identific ation Number is located
in different p laces:
- under the w indshield on the driver's s ide
~fig . 231.
- in the MMI : Select: Function button ICAR I >
(Car) * syst ems > VIN number .
-on the veh icle identification label.
Vehicle identification label
The vehicle identification labe l is located in
the luggage compartment in the spare wheel
well. T
he label ~
fig. 232 shows the fo llowing vehi ­
cle data:
(D Vehicle Iden tificat io n Num ber (V IN)
@ . Vehicle type, engine o utput, transmission
® Engine and transm iss ion code
@ Pain t number and inte rior
® Optional equipment numbers
T he information of the vehicle identification
label can also be found i n your Warranty
&
Maintenance booklet.
Safety compliance sticker
The safety compliance sticker is your assur ­
ance that yo ur new veh icle complies with all
applicable Federa l Motor Vehicle Safety
Standards which we re in effect at the time the
vehicle was manufactured. You can find this
sticker on the door jamb on the driver's side.
It shows the mo nth and year of production
and the vehicle ident ificat io n number of your
vehicle (perfo rat io n) as well as the Gross Ve hi­
cl e Weig ht Rating (GVWR) a nd the Gross Ax le
Weig ht Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine
hood re lease . The spar k ign it ion sys tem com·
plies wi th the Ca nadian standard IC ES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle We ight Rat ing (GVWR), and
t h e Gross Axle Weight Rat ing (GAWR) for
fron t and rear are liste d on a sticker on the
doo r jamb on the d river's side .
T he Gross Vehicle We ight Rat ing includes the
weight of the bas ic vehicle plus f ull fuel tank,
o il and coo la nt, plus max imum load, which in­
cl udes passe nger we igh t (150 l bs/68 kg per
designate d sea ting posi tion) an d lugg age
weight ~&. - .,.

29 2 Index
Certification ...... ..... ... .. .. .... . 288
Changing a wheel .............. .. ... 266
Changing engine oi l ........ .. .. .. .. . 233
Chec king
Engine coolant leve l .... ... .. .. .... . 235
Tire pressure ... .. ..... ... .. .. .... . 249
Ch ild restra ints
Da nger of us ing ch ild restra ints in the
front seat . . . . . . . . . . . . . . . . . . . . . . . . 151
Where can I get additional information
about child restraints and their use? .. 193
Ch ild restra int system anchors ... ..... 189
Ch ild safety .. ..... ........ .. .. .... . 175
Convertible locking retractor . . . . . . . . . 186
Important safety instructions for using
ch ild safety seats ........... .. .. .. . 179
I mportant th ings to know when dr iving
with ch ildren . ............. .. .... . 175
Tether anchors .................... 192
Tether straps .. ... ...... ... .. .... . 192
Ch ild safety lock
Rear doors . .............. ... .. .... 40
Child safety seats .............. .... . 181
Boo ster se ats . . . . . . . . . . . . . . . . . . . . . 184
Convertible child seats ............. 182
Conve rtible locking retractor ......... 186
H ow do I properly install a child safety
seat in my vehicle? ...... .. .. .. .. .. . 179
I nfant sea ts ............. .. .. .. .. . 181
I nstall ing .... ............. ...... . 186
I nstalling a child restraint using the
L ATCH system .. .. ..... ... .. .. .... . 191
LATCH system ... .. .... ... .. .. .. .. . 19 1
Lower anchorages ............ .... . 190
Mount ing and releasing the anchorage
hook .. .. .. ... .... ...... ... ... .. . 191
Safety instructions . . . . . . . . . . . . . . . . . 179
Unused safety belts on the rear seat .. 181
C igarette lighter . . . . . . . . . . . . . . . . . . . . . 59
C le a ning .. .. .. . .......... .. .. .. .. . 213
Climate control Air vents ... ... .... ...... ... ... .. .. 71
Climate controls . . . . . . . . . . . . . . . . . . . . . 69
C limate con trol system
Supp lementary hea ter ... .. .. .. .... . . 74
Climate control (four-zone)
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 72 Climate control (three
-zone)
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 70
Clock .............................. 28
Closing Rear lid ........................... 38
Sl id ing/tilting sunroof ............. .. 42
Co ld tire inflation pressure ..... ... .. .. 247
Coming home ... .. ............. .... . 46
Compact spare tire .............. .... 265
Compartments . . . . . . . . . . . . . . . . . . . . . . 60
Compliance . . . . . . . . . . . . . . . . . . . . . . . . 288
Consumer Information . . . . . . . . . . 138, 285
Consumption (fuel) ... .......... .. .. . 25
Co ntacting NHTSA . ................ . 138
Controls Cleaning . ..... .. .. ... ..... ... .. .. 215
Co nvenience key . . . . . . . . . . . . . . . . . . . . . 36
Star ting the engine ............ .. .. . 76
Stopping the eng ine (START ENG IN E
STOP button) . . . . . . . . . . . . . . . . . . . . . . 77
Switching the ignition on .... ... .. .. . 76
Un locking and locking vehicle ......... 36
Converti ble child sa fe ty seats ..... .... 182
Co nvertib le locking retractor
Activati ng .... .... ............... . 188
Deact ivat ing . .. .. .......... ...... . 188
U si ng to secu re a child safety seat 1.86, 188
Coolant
refer to Engine coolant ............ . 234
Cooling mode (automatic climate control) 72
Cooling mode (climate control) ......... 70
Cruise contro l
Changi ng speed .. .. ... ....... ... .. . 85
Presett ing your speed ............... 85
Switching off .. .................... 85
Switch ing on . .. .. ... .......... .. .. . 84
Warning/ind icator lights ........ .. .. . 24
(upholder .. .. ... . .. .... .... ... .. .. . 60
C u rve light . ..... .. ... .. ..... .... . .. 102
Cylinder on demand System ........... 27
D
Data recorder ... ................... 196
Date disp lay . ..... .. .... .... ... .. .. . 28
Daytime run ning lights ........... .. .. . 44