2014 AUDI A5 CABRIOLET battery

220 Check ing and filling
- To r educe the danger of explosion, never
co nnect or disconn ect cha rger cables
wh ile the c harger is operating.
- Fast char ging a battery is dangerous and
shou ld on ly be attempted by a compe­
tent technician w ith the proper equip­
ment .
- Battery acid that may spill d uring charg­
ing should be washed
off with a solution
of warm water and baking soda to neu ­
tralize the acid.
(Q) Note
Never use a fast charger as a booster to
start the engine . This will seriously dam­
age sensitive electronic components, such
as control units, relays, rad io, etc., as we ll
as the battery charger.
Battery replacement
The new battery must have the same specif/·
cations and dimensions as the original equip­
ment battery.
In tell igent energy management in your veh i­
cle is respons ible for d istributing the e lectr i­
cal energy throughout you r vehicle
~ page 185. The intell igen t energy m anage­
men t system w ill keep the engine ba tte ry
charged better then vehicles w ithout this sys­
tem . To make sure the additional e lectrica l en­
ergy is available once again after you have
changed the battery, we recommend that you install batteries o f the same type and ma nu­
facture only (the same as those installed at
the time your vehicle was delivered). Specifi­
cations are listed on the battery hous ing. You r
author ized Audi dealer must code the battery
in the ene rgy managemen t system to enable
you to use the ene rgy management functions
correctly after replac ing the battery.
I f it is not poss ible to use a battery of this
type, the new bat tery m ust h ave the s ame ca­
pac ity, voltage ( 12-volts), amperage, con ­
struction and plug sea ling. When installing the battery, make su
re the ig ­
nition and a ll electrical consumers are turned
off.
(D Note
Make sure the ventilat ion hose on the side
of the battery is connected, otherwise
fumes or battery acid can leak out .
@ For the sake of the environment
Because o f the p rob lem of p roper disposal
of a battery, we recommend your author ­
i zed Audi dealer change the battery fo r
you. Batteries contain sulfur ic acid and
l ead and must always be disposed of prop­
erly in comp liance with all environmental
regula tions. Dispos ing of veh icle batter ies
i mprope rly is very dange rous to the envi­
r o nment .
Windshield/headlight*
washer container
Fig. 181 En gin e compa rt m en t: Cove r on the w ind·
s h iel d a nd h eadligh t• was he r fl uid conta in er
.., N
-~ (X) a,
The washer fluid conta iner is marked w ith the
symbol
O on its cap~ fig. 181, ~ page 208,
fig . 175.
.. Before yo u check any thing in the engine
compa rtment,
always read and heed all
WARNINGS q A in Working in the engine
compartment on page 206 .
.. Lift the fi ller cap tongue to add washer flu­
id. You can f ill the container to the top.
.. Press the cap back onto the filler neck after
fi lling the conta iner .
You can find the reservo ir
capacity in the table
in
q page 262. .,.

224 Tires and wheels
Gross Vehicle Weight Rating ("GVWR" )
means the maximum total loaded weight o f
the vehicle.
Groove
means the space between two adjacent tread
ribs.
Load rating (code)
means the maximum load that a tire is rated
to carry for a given inflat ion pressure. You
may not find this informat ion on all tires be­
cause it is not requ ired by law .
Ma ximum load rating
means the load rating for a t ire at the maxi­
mum permissible inflation pressure for that
tire .
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity we ight, and
(d) Production opt ions weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressure
to which a tire may be inflated . Also called
"maximum inflation pressure."
Normal occupant weight
means 150 lbs. (68 kilog rams) times the
number of occupants seated in the vehicle up
to the tota l seating capacity of your vehicle.
Occupant distribution
means dist ribution of occupants in a veh icle.
Outer diameter
means the overall diameter of an inflated new
tire.
Overall width
means the linear distance between the exteri ­
ors of the sidewalls of an inflated tire, includ­
ing elevations due to labeling, decorations, or
protective bands or ribs .
Ply
means a layer of rubbe r-coated parallel cords.
Production options weight
means the combined weight of those installed
regular production opt ions we ighing over 5
lbs. ( 2.3 kg) in excess of those standa rd items
wh ich they replace, not previously cons idered
in curb weight or accessory weight, including
heavy duty brakes, ride levelers, heavy duty
battery, and specia l trim .
Radial ply tire
means a pneumat ic tire in which the ply cords
that extend to the beads are laid at substa n­
tially 90 degrees to the centerline of the
tread.
Recommended inflation pressure
see <=;> page 223, Cold tire inflation pressure .
Reinforced tire
means a tire design to operate at higher loads
and at h igher inflation pressures than the cor­
responding standard tire. Reinforced tires
may be identified as "XL", "xl", "EXTRA LOAD",
or "RF" on the sidewal l.
Rim
means a metal support for a tire or a t ire and
tube assembly upon which the tire beads are
seated .
Rim diameter
means nominal diameter of the bead seat. If
you change your wheel s ize, you will have to
purchase new tires to match the new rim di­
ameter .
Rim size designation
means rim diameter and width.
Rim width
means nom inal d istance between rim flanges.
Sidewall
means that portion of a tire between the
tread and bead .

Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently
largecross section to carry the starter current
safely. Refer to the manufacturer's specifica­
tions.
Use only jumper cables with
insulated termi­
nal clamps which are distinctly marked:
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
Emergency situations 255
-A discharged battery can freeze at tem­
peratures just below 32 °F (0 °C). Before
connecting a jumper cable, you must
thaw the frozen battery completely, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to
start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with
a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery. Use of batteries of different voltage
or substantially different "Ah" rating
may cause an explosion and personal in­
jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The ca pa city (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
page 206.
(D Note
- Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc.
- There must be no electrical contact be­ tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,. •
•

256 Emergency situations
@ Tips
The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative post
because the batte ry manager system must
be able to detect the battery 's state of
charge. Always connect the negative
ground cab le to the negative ground post
of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below!
Fig. 201 Engine compartment: Connectors fo r jum per
cables and charger
Fig. 202 Jump sta rting wi th the battery of anot her ve ·
h ide :@ booster battery, @ disc harged vehicle battery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your vehicle .
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever
of automatic transmission to N (Neutral) or
P (Park) and set parking brake .
Connect POSITIVE(+) to POSITIVE(+)
(red)
.. Remove the cover above the jump start con­
nection .
.. Open the cover on the positive pole
¢fig. 201.
1. Connect one end of the red positive cable
on the
jump start bolt c::> fig. 202 @
(Bolts under cover= "positive") of the ve­
hicle to be started @.
2. Connect the other end to the positive ter-
minal @of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the b lack negative ca­
ble to the negative terminal @of the
booster battery @.
4. Connect the other end to the
jump start
bolt @
(Bolts with hex head= "negative")
of the vehicle to be started @.
Starting the engine
.. Start the engine of the vehicle with the
booster battery@. Run the engine at a
moderate speed.
.. Start engine with discharged vehicle battery
@ in the usual manner .
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds .
Wait for about 30 seconds and then try
again .
.. With eng ine running, remove jumper cables
from both vehicles in the exact
reverse or­
der .
.. Close the cover on the positive pole .
T he battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connect­
ed with their
metal parts in full contact with
the battery terminals.
A WARNING
--
To avoid serious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable manufac-
turer . If in doubt, call for road service . ..,.

-Jumper cables must be long enough so
that the vehicles do not t ouch.
- W hen connecting jumper ca bles, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment.
- Do not bend over the batteries - danger
of chemical burns!
- The battery ce ll locking screws must be
t ightened securely .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 206.
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI ­
TIVE(+), and NEGATIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
ce lls are screwed in firmly . If not, tighten
plugs p rior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
necting a jumper cable as described
above applies spec ifically to the case of
your vehicle be ing jump started. When
you are givi ng a jump start to another ve­
hicle, do
not connect the negat ive( -) ca­
ble to the negat ive( -) term inal on the
discharged battery @¢
fig. 20 2. In­
stead, securely connect the negative(- )
cable to e ither a solid metal component
that is firmly bolted to the engine block
or to the engine block itse lf. If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and explode!
Em erg en cy si tuation s 257
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow t ruck operators who know
how to operate their equipment safely.
- Never tow your Audi , towing will cause
damage to the engine a nd transmi ssion.
- Never wrap th e safet y chain s or winch c a­
ble s around th e brak e lin es.
- To prevent unne ce ss ary dam age, your Aud i
mu st be t ransp orted with a flat bed truck .
- To load th e vehi cle on to the fl at bed , use
the t owing loop found in the vehicle t ool s
and atta ch to the front or rear anch o rage
r=:> page 258 and ¢page 258 .
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.
-
•
•

Technical Data
Vehicle identification
F ig. 210 Veh ide Identificat ion Number (VlN) plate: lo ·
c ation on d river 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -IIOO -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JDZ 1LB lA S 1BA
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824
D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413
50 2
1S A 7GB QlA 4GO
XX. X XX X XX X XXXX
Fig. 211
The vehicle identification label: ins ide the lu g·
ga ge compar tmen t
Vehicle Identification Number (VlN)
The Veh icle Iden tifica tion Number is located
in different p laces :
- under the windshield on the driver's side
9fig.
210.
- in the radio or in the MM!*: Select: ICARI
function button > Vehicle ID number (VIN)
or select: I CAR I function button> Car sys­
tems*
control button > Servicing & checks >
VIN number .
-on the vehicle identification label. Technical Data 261
Vehicle identification label
The
vehicle identification label is located in
the luggage compartment near the battery.
T he label 9fig.
211 shows the follow ing vehi­
cle data :
(D Vehicle Identificat ion Number (VIN)
@ Vehicle type, engine output, transm ission
@ Engine and transmission code
© Paint number and interior
® Optional equipment numbers
T he information of the vehicle identification
label can also be found in your Warranty
&
Maintenance booklet.
Safety compliance sticker
The safety compliance sticker is your assur­
ance that your new vehicle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured . You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and the vehicle identification number of your
vehicle (perforation) as well as the Gross Vehi­
cle Weight Rating (GVWR) and the Gross Ax le
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine hood release. The spark ign ition system com­
plies with the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
door jamb on the driver's s ide .
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oil and coo lan t, plus maximum load , which in­
cludes passenger we ight (150 lbs/68 kg per
designated seating position) and luggage
weight
9 ,&. .

270 Index
Automatic climate control Air vents ... ............... .. .... ..
71
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 70
Setup . .. ............... .. .. .... .. 72
Automatic power top ................. 42
Automatic Shift Lock (ASL) . . . . . . . . . . . .
86
Automatic transm ission . . . . . . . . . . . . . . . 85
Automatic Shift Lock (ASL) . . . . . . . . . . . 86
Driving .. .. ............. .. .. .. ... . 87
Emergency mode . . . . . . . . . . . . . . . . . . . 91
Emergency release . . . . . . . . . . . . . . . . . . 91
Kick-down . . . . . . . . . . . . . . . . . . . . . . . . . 90
Manual shift program ..... .. .. .. .. . . 89
Removal lock (ignition key) ... .. .. .. . . 74
Selector lever . . . . . . . . . . . . . . . . . . . . . .
85
Automatic wipers . . . . . . . . . . . . . . . . . . . . 56
Auto Safety Hotline ............ .... . 129
Average speed . . . . . . . . . . . . . . . . . . . . . . . 25
Avoid damaging the vehicle . . . . . . . . . . . 187
B
Battery . . . . . . . . . . . . . . . . . . . . . . . 17,217
Battery locat ion inside the luggage com-
partment ................. .. .... .
217
Charging ... .................. ... . 219
Important warn ings when working on
the battery . . . . . . . . . . . . . . . . . . . . . . .
217
Jump starting .............. .. .. .. . 255
Low . .. .. .. ... .......... .. .. .. .. . 185
Replacing the battery ........... .. . 220
State of charge ............ ... .... .
185
Winter operation .......... ... .... . 217
Working on the battery ............. 217
Before driving ............. .. .. .. .. . 121
Belt positioner .. .. ..... ..... .. .. .. . 135
Bio-ethanol (Fue l) ............ .. .... . 202
Blended gasoline .......... .. .. .. .. . 201
Blower (automatic climate control) . . . . . . 71
Booster seats .............. ... .... . 169
Brake fluid
Changing the brake fluid ........ ....
216
Check ing the brake fluid level . .. ..... 216
Reservoir .... ........... .. .. .. .. . 216
What is the correct brake fluid leve l? .. 216
What should I do if the brake fluid warn-
ing light comes on? ........ ..... .. .
216
Brake system .... .. ............. .... 216
Anti- lock braking system ............. 19
Brake assist system ................ 179
Brake fluid .... .. ............. .... 216
Brake fluid specifications for refill and re-
placement ...... ................ .
216
Brake light defective . . . . . . . . . . . . . . . . 21
Brake power assist unit ............. 182
Brakes .. .. .. .. . .............. .. .. 182
Ceramic brakes . .. ... .......... .. .. 182
Electromechanical parking brake ...... 79
Warning/indicator lights .......... .. . 15
Worn brake pads symbol . . . . . . . . . . . . . 20
Braking
Emerg ency braking funct ion ... .. .. .. .
81
braking guard . . . . . . . . . . . . . . . . . . . . . . . 93
Messages ........ ............... . 100
Settings ........ .. .............. . 100
Break-in period . . . . . . . . . . . . . . . . . . . . . 187
Tires . .. .. .. .. .. ............. .. .. 187
Bu lbs ..... ..... .. ............. .... 253
C
Californ ia Proposition 65 Warn ing . .... 207
Batte ry specific .. ... .......... .. .. 218
Capac1t1es ........ .. .............. . 262
Carbon parts
Cleaning . . . . . . . . . . . . . . . . . . . .
197,198
Care ... .. .. .. .. .. ............. .. .. 195
Cargo area
refer to Luggage compartment. .. 67, 127
Catalytic converter ................. . 188
Center armrest . . . . . . . . . . . . . . . . . . . . . . 63
Central locking ...................... 31
Central locking switch ............... 35
Convenience key .. .. ..... ........ .. . 35
Remote control key . . . . . . . . . . . . . . . . . 34
Ceramic brake rotors New brake pads .. ............. ....
182
Certification . ..... ................. 267
Changi ng a flat tire ................. . 244
Changing a wheel .. ............. .... 244
Changi ng engine oil ............. ....
212
Checking
Engine coolant level ................
213
Checking tire pressure ........... .... 228

272 Index
Homelink universal remote contro l 267
Remote control key ...... ... .. .... . 267
Decorative parts/trim
C leaning . .. ............. .. .. .. .. . 197
Defective light bulb warning . . . . . . . . . . . 21
Defrosting (windows) ........ ... .... .. 71
Determining correct load limit ..... .. . 231
Digita l clock .............. .. .. ...... 12
Digital compass ............. .. .... .. 58
Dimensions .. .. .. ...... .... ... .. .. . 262
Dimming the rearview mirror . ..... .. .. 55
Displays Cleaning . ... ............ .. .. .. .. . 197
Doors emergency lock ing .. ...... .. .. .. .. .. 36
Driver information system Open door or front lid warning . . . . . . . . 24
Outside temperature display .. .. .. .... 24
Sound system display . . . . . . . . . . . . . . . 24
Driver seat
refer to Seating position ............ 122
Driving safely ........... .. .. .. .. .. . 121
Driving through water ...... .. .. .... . 187
Driving time . . . . . . . . . . . . . . . . . . . . . . . . 25
Dust filter
refer to Pollutant filter (automatic AC
system) ................. .... ...... 69
Dynamic steering . . . . . . . . . . . . . . 106, 184
E
E85 (Fuel) . ................. .. .. .. . 202
Easy entry function ......... .... .... .. 62
Efficiency program ........... .. .. ... . 27
Fuel economy messages . ........ .. .. 27
Memory levels . . . . . . . . . . . . . . . . . . . . . 25
Other equipment ........... .. .. .. .. 27
Electro-mechanical power assist .. .. .. . 184
Electromechanical parking brake
Emergency braking ........ ... .... . . 81
Indicator light . . . . . . . . . . . . . . . . . . . . . 79
Parking ...... ........... .. .. .... .. 80
Releasing and closing ......... .. .... 79
Starting ass ist .. .. .... ... .. .. .. .. .. 80
Starting from rest ........ .. .. .. .. .. 80
Starting off with a tra ile r ... .. .. .. .. . . 81
War ning/ indicator l ights ... .... .... .. 16 Electronic
differential lock
Warning/indicator lights ............. 18
El ectronic differential lock (ED L) ... .... 179
Warning/indicator lights .......... .. . 19
Electronic immob ilizer . . . . . . . . . . . . 12, 37
E lectronic power control
(EPC) warning/indicator light . . . . . . . . . 20
Electronic speed limiter .............. . 29
Electronic stabilization control Sport mode ..... ... ....... ... .. .. 181
E lectronic Stabilization Contro l (ESC) ... 179
Warning/indicator lights ............. 18
Emergency actuation
Doors .... .. .. . .............. .... . 36
Ignition key ..... ................ .. 34
Emergency braking . ... .. ..... ... .. .. . 81
Emergency flasher . . . . . . . . . . . . . . . . . . . 53 Warning/indicator lights ............ . 23
Emergency key . . . . . . . . . . . . . . . . . . . . . . 32
Starting engine . . . . . . . . . . . . . . . . . . . . 76
Emergency operation
Emergency braking funct ion (pa rking
brake) .. .. .. .. .. ................. . 81
Luggage compartment lid . . . . . . . . . . . . 38
Power top . . . . . . . . . . . . . . . . . . . . . . . . . 46
Emergency starting ... ....... ... .. .. 255
Emergency towing .................. 257
Energy management . . . . . . . . . . . . . . . . 185
Battery power . . . . . . . . . . . . . . . . . . . . . 17
Driver notification . . . . . . . . . . . . . . . . . . 17
Engine Compartment ................... .. 208
Coolant ..... .. .. .. ........... .... 213
Data ......... .. .. ............ ... 263
Hood ............................ 206
Starting . . . . . . . . . . . . . . . . . . . . . . 7 4, 77
Starting with jumper cables ......... 255
Stopping . . . . . . . . . . . . . . . . . . . . . . 76, 78
Engine compartment
Safety instructions ................. 206
Working the engine compartment 206
Engine coolant
Indicator light . .. ............... ... 17
Engine coolant system ..... ...... .... 213
Adding coolant . .. ... .. ..... ... .. .. 214
Checking coolant level . ...... ... .. .. 213